Instrukcja obsługi QTX HIPAR-100

QTX Ulga HIPAR-100

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla QTX HIPAR-100 (6 stron) w kategorii Ulga. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
HIPAR-100
OUTDOOR LED PAR CAN RGBWA
Item ref: 154.323UK
User Manual
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
Powered by TCPDF (www.tcpdf.org)
154.323UK User Manual
Introduction
Thank you for your purchase of the QTX HIPAR-100 outdoor LED PAR light. This fixture has been designed to
provide powerful and colourful light coverage to a wide area for indoor or outdoor areas Please read and keep
this manual for reference to gain the best results from this product and avoid damage through misuse.
SAFETY SYMBOL AND MESSAGE CONVENTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
This symbol indicates that dangerous voltage constituting a risk of
electric shock is present within this unit
This symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this unit.
Warning
To prevent the risk of fire or electric shock, ensure all power connections are watertight.
No user serviceable parts inside – Do not open the case – refer all servicing to qualified service personnel.
Safety
Check for correct mains voltage and condition of power lead before connecting to a power outlet.
Placement
• Use the included dual mounting bracket to fix to a stand/truss or free-standing on a stable surface
• Use secondary safety fixings if mounting overhead.
• Ensure adequate airflow around the fixture housings
• Ensure adequate access to controls and connections
Cleaning
• Use a soft cloth with a neutral detergent to clean the casing as required
• Do not use strong solvents for cleaning the unit
In the box
Please open the package carefully and check that all contents are present and in good condition.
Contact your retailer if any part is missing or broken.
• HIPAR-100 LED PAR can
• Dual mounting bracket
• UK mains plug to waterproof socket lead
• DMX XLR plug to waterproof socket lead
154.323UK User Manual
Rear panel
Installation
The HIPAR-100 is supplied with a dual hanging bracket, which can also be used as a free-standing support.
When installing the fixture, ensure all fixings are secure, controls and connections are accessible and allow
enough space for air to circulate around the housing. Do not aim directly in line of sight or very close to
people where the extremely bright output of the fixture may be harmful to eyesight.
The HIPAR-100 is IP65 weatherproof and all electrical connections are hard-wired with waterproof connectors.
An XLR to waterproof connector is provided for adapting the DMX input lead to a standard DMX signal input.
A mains plug to waterproof connector is provided to adapt the power input lead to a standard mains supply.
Connect the waterproof connectors securely, ensuring that the notches are aligned for correct polarity.
The waterproof plugs have a threaded collar which must be fully tightened onto the waterproof socket.
The HIPAR-100 also has DMX through and power through leads for connecting onto further HIPAR cans in a
daisy-chain manner. Ensure that the mains power supply is capable of the total load of all cans connected.
Setting up
Check all connections are properly made and power up the HIPAR-100 can.
The LED display will light and show the current mode or status.
Use the control panel keys to adjust the stand-alone or DMX control settings.
Press MENU to step through the menu options and press ENTER when you reach the required page.
Press UP and DOWN keys to adjust the value of the parameter and press ENTER again to confirm.
Press MENU again to go back to stepping through menu options.
Please see the table on the following page for the full list of menu options.

Specyfikacje produktu

Marka: QTX
Kategoria: Ulga
Model: HIPAR-100

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z QTX HIPAR-100, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Ulga QTX

QTX

QTX DM-X12 Instrukcja

15 Października 2024
QTX

QTX HPWash100 Instrukcja

6 Października 2024
QTX

QTX Moonglow Instrukcja

6 Października 2024
QTX

QTX Recharge Performer Instrukcja

27 Września 2024
QTX

QTX Wash & Beam Instrukcja

27 Września 2024
QTX

QTX TetraCube Instrukcja

27 Września 2024
QTX

QTX BATPAR-18W Instrukcja

27 Września 2024
QTX

QTX TinyMover Instrukcja

27 Września 2024
QTX

QTX Recharge DJ Instrukcja

27 Września 2024
QTX

QTX Multi-Bar Instrukcja

27 Września 2024

Instrukcje Ulga

Najnowsze instrukcje dla Ulga

Goobay

Goobay 30780 Instrukcja

15 Października 2024
Livarno

Livarno IAN 94799 Instrukcja

15 Października 2024
Astro

Astro Denia Instrukcja

13 Października 2024
AFX

AFX Grace GRCP07CBBK Instrukcja

12 Października 2024
AFX

AFX Point PNTP0107L30D1BK Instrukcja

12 Października 2024
Neewer

Neewer TL97C Instrukcja

9 Października 2024
Neewer

Neewer SRP18C Instrukcja

9 Października 2024
Ikea

Ikea STRÅLA 005.824.56 Instrukcja

9 Października 2024
Ikea

Ikea STRÅLA 705.829.38 Instrukcja

9 Października 2024
Ikea

Ikea STRÅLA 105.632.59 Instrukcja

9 Października 2024