Instrukcja obsługi QSC SC-2150

QSC głośnik SC-2150

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla QSC SC-2150 (7 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/7
TD-001624-01-A
*TD-001624-01*
SC-2150
Quick Start Guide
SC-2150 Screen Channel Loudspeaker System
®
2
TD-001624-01-A
EXPLANATION OF SYMBOLS
The term
“WARNING!”
indicates instructions regarding personal safety. If the instructions are not followed the result may be bodily injury or death.
The term
“CAUTION!”
indicates instructions regarding possible damage to physical equipment. If these instructions are not followed, it may result
in damage to the equipment that may not be covered under the warranty.
The term IMPORTANT! indicates instructions or information that are vital to the successful completion of theprocedure.
The term
"NOTE"
is used to indicate additional useful information.
The intent of the exclamation point within an equilateral triangle is to alert the user to the presence of important safety, and
operating and maintenance instructions in this manual.
IMPORTANT SAFETY INSTRUCTIONS_____
Refer to TD-000142 Safety Precautions contained in the shipping carton.
Warranty
For a copy of the QSC Limited Warranty, visit the QSC website at www.qsc.com
Introduction
The SC-2150 is a 3-way, selectable passive full-range or bi-amplified screen channel loudspeaker system comprised of two main units. These
units are shipped in separate cartons.
DCS-2150-HF Mid-High Frequency Loudspeaker System
Part Quantity
DCS-2150-HF Loudspeaker System 1
Wiring Harness *
TD-000142 Safety Precautions 1
TD-000453 Warranty 1
* Part of the HF Loudspeaker System
DCS-2150-LF Low-Frequency Enclosure
Part Quantity
DCS-2150-LF Loudspeaker Enclosure 1
Hex-head Screw 3
Flat Washer 3
Split Washer 3
TD-000142 Safety Precautions 1
TD-000453 Warranty 1
— Figure 1 —
DCS-2150-HF
DCS-2150-LF
3
TD-001624-01-A
Assemble the SC-2150
This procedure assumes that both items and associated hardware is unpacked and the two
units are placed on a solid flat surface near the installation location.
Refer to — Figure 2
1. Place the HF horn assembly (1) on top of the LF enclosure (2) with the three holes in
the pan-and-tilt bracket (not visible in the illustration), aligned with the three holes (3)
in the top of the LF enclosure.
2. Assemble the three bolts (4a), split washers (4b), and flat washers (4c) and install
through the pan-and-tilt bracket into the LF enclosure.
3. Tighten the bolts. Be careful not to over tighten.
Refer to — Figure 3
4. Connect the Neutrik SpeakON NL4 plug (1) (end of the wiring harness coming from the
HF System) to the LF Enclosure connector plate NL4 receptacle (2).
NOTE:The NL4 is a keyed plug/receptacle that can only go in one way.
5. After engaging the plug all the way, twist the plug clockwise until it locks.
6. Use the Mode switch (3) to select Bi Amp or Passive.
Passive Mode
– (— Figure 4) a single amplifier channel drives the entire system. The
Mode Switch (3) must be in the PASSIVE position and only the right-side pair of terminals
are used to connect the amplifier to the loudspeaker system.
Bi-Amp Mode
– (— Figure 5) two amplifier channels are required. One for the LF
enclosure and one for the Mid-Hi system.
CAUTION!
An active crossover must be used to protect the loudspeaker from
damage. It is highly recommended to use a QSC processor with factory DSP
presets for the SC-2150 for best results.
The Mode Switch must be in the BI-AMP position and all four terminals are used to connect the amplifier to the loudspeaker. The Low
Frequency amplifier connects to the left pair of terminals and the High Frequency amplifier connects to the right pair of terminals.
CAUTION!
In all cases, be sure to observe proper polarity when making connections. The “+” terminal of the amplifier
should connect to the “+” terminal of the loudspeaker.
In Bi-Amp mode, be sure that LF and HF connections are not reversed. HF drivers can be damaged if they are connected
to the low frequency amplifier.
— Figure 2 —
1
2
3
4
4a
4b
4c
DCS-2150-HF
DCS-2150-LF
— Figure 3 —
To Mid-High System
1
2
3
®
— Figure 4 —
To amplier channel
— Figure 5 —
To amplier channel two (HF)
To amplier channel one (LF)


Specyfikacje produktu

Marka: QSC
Kategoria: głośnik
Model: SC-2150

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z QSC SC-2150, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje głośnik QSC

QSC

QSC HF-63X1 Instrukcja

7 Stycznia 2025
QSC

QSC WL115-sw Instrukcja

7 Stycznia 2025
QSC

QSC AD-C42T Instrukcja

7 Stycznia 2025
QSC

QSC SR-18 Instrukcja

7 Stycznia 2025
QSC

QSC SC-312X Instrukcja

7 Stycznia 2025
QSC

QSC SR-26 Instrukcja

7 Stycznia 2025
QSC

QSC SC-312 Instrukcja

7 Stycznia 2025
QSC

QSC SC-422 Instrukcja

7 Stycznia 2025
QSC

QSC SC-423 Instrukcja

7 Stycznia 2025
QSC

QSC AD-C6T-HC Instrukcja

7 Stycznia 2025

Instrukcje głośnik

Najnowsze instrukcje dla głośnik