Instrukcja obsługi QSC ADP-P.SUB

QSC głośnik ADP-P.SUB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla QSC ADP-P.SUB (11 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/11
Acoustic Design Series
Quick Start Guide
AD-P.SUB
AD-P.SAT
TD-001564-01
*TD-001564-01* 1
EXPLANATION OF SYMBOLS
The term “WARNING” indicates instructions regarding personal safety. Failure to follow them may result in bodily injury or death.
The term indicates instructions regarding possible damage to physical equipment. equipment damage “CAUTION” Failure to follow them may result in
to equipment that may not be covered under the warranty.
The term “IMPORTANT” indicates instructions or information that are vital to the successful completion of theprocedure.
The term indicates additional useful information.“NOTE”
The lightning flash with arrowhead symbol in a triangle alerts the user to the presence of uninsulated dangerous voltage within the product’s
enclosure that may constitute a risk of electric shock to humans.
The exclamation point within a triangle alerts the user to important safety, operating, and maintenance instructions in this manual.
1. Read these instructions and keep a copy for future reference.
2. Strictly follow and heed all instructions and warnings.
3. Consult a licensed and qualified professional engineer to devise and/or review an appropriate pendant mounting scheme.
4. Do not use or submerge this loudspeaker product in or near water or liquids.
5. Clean only with a dry cloth. Do not use any aerosol spray, cleaner, disinfectant or fumigant on, near, or into the loudspeaker product.
6. Do not block any ventilation opening. Install in accordance with the manufacturer’s instructions.
7. Do not install the loudspeaker near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers).
8. Do not use any attachments, accessories, mounts, or brackets that are not specified or approved by QSC, LLC.
9. Refer all service to qualified personnel. Service is required if the hanging mechanism or loudspeaker have been damaged in any way, such as liquid
having been spilled or objects have fallen into the loudspeaker or the loudspeaker has been exposed to rain or moisture, does not operate normally,
or has been dropped.
10. Observe all applicable local codes.
11. Consult a licensed, professional engineer when any doubt or questions arise regarding a physical equipment installation.
Maintenance and Repair
Advanced technology—e.g., the use of modern materials and powerful electronics—requires specially adapted maintenance and repair methods. To
avoid subsequent damage to the equipment, personal injury, and/or creation of additional safety hazards, have all maintenance or repair work on the
equipment performed only by a QSC authorized service station or an authorized QSC International Distributor. QSC is not responsible for any injury, harm,
or related damages that arise from any failure of the customer, owner, or user of the equipment to facilitate those repairs.
Warranty
For a copy of the QSC Limited Warranty, visit the QSC website at www.qsc.com
IMPORTANT SAFETY INSTRUCTIONS
TD-001564-01 2
Suspend the Subwoofer
WARNING!: Do not attach the snap hook to
the loudspeaker or any other load until the
hanger cable has been anchored to a suitable
structural member.
1. Insert the wire cable into the appropriate hole in the slip-lock fastener
(see Figure 1). The fastener’s two holes are directional, so cable will
only insert one way; if it will not go through, the cable is inserted into
the wrong hole.
2. Loop the cable over the structural member where the subwoofer is
to hang. The structure must be capable of supporting at least 5× the
weight of the subwoofer—AD-P.SUB: 17.5 lb or 8 kg.
NOTE: Building codes in some jurisdictions
may require higher safety factors.
Note that the subwoofer uses two hanger cables.
3. Insert the cable through the other hole in the fastener.
4. Adjust the length of the cable hang so the snap hook is at the desired
height. To shorten the hang, simply pull the cable further through one
or both holes in the fastener (Figure 2). To lengthen the hang or to
remove the cable from the structural member, insert the release key
into the appropriate release key hole; this will unlock that hole in the
fastener and allow the cable to move in the other direction (Figure3).
WARNING!: Never insert the release key while
there is a load on the hanger cable.
5. Repeat for the other hanger cables.
6. Attach both snap hooks to the suspension tab on the subwoofer
(Figure 4). Make sure the safety latch on the hook closes fully with the
subwoofer attached before you transfer the weight of the subwoofer to
the cables.
Install the AD-P.SUB Subwoofer
What’s in the AD-P.SUB Box
— Figure 1 —
Insert cable
here
Release
key hole
End view
— Figure 2 — — Figure 3 —
Structural
member
Pull cable to
shorten hang.
Insert release
key to lengthen
hang or remove.
Insert cable
here
Release
key hole
End view
Structural
member
Structural
member
1×
AD-P.SUB
1×
Cover 1
1×
Cover 2
8×
Screw
2×
Hanger cable
with slip-lock
fastener
3×
Euro-style plug
1×
Magnetic
grille
1×
Warranty
1×
Quick Start
Guide
TD-001547
TD-001564-01 3
Wire the Subwoofer
We recommend using insulated twisted pair stranded copper wire of an
adequate gauge to minimize resistive losses. To facilitate connection,
the AD-P.SUB loudspeakers have a four-pole connector for the input and
two more for the high-pass outputs to as many as four 16Ω satellite
loudspeakers (Figure 5). Each subwoofer comes with three Euro-style four-
pole pluggable connectors with clamping screws for securing to the wire
conductors.
1. Remove the magnetic grille and set the transformer tap switch to the
desired power (in watts) or to 4Ω for low-impedance operation (Figure
6). Reattach the grille. This setting can always be readjusted in the
future as needed.
2. On the top of the enclosure, remove the two protective covers over
the input and output connectors. The smaller cover has one gland
(protective cable pass-through) and the larger one has two.
3. Route the wires coming from the amplifier through the gland in the
smaller cover. Route the wires for the satellte loudspeakers through one
or both glands on the larger cover.
4. Strip the wire ends about 6 mm or about 1/4 inch.
5. Connect the pairs of wires to the + and - terminals of the Euro-style
connectors as shown in Figure 7. Tighten the clamping screws to hold
the wires securely.
To daisy-chain forward to another loudspeaker, route a second wire
pair through the gland and attach them to the THRU terminals of the
input Euro-style connector. Be mindful of polarity when connecting
multiple loudspeakers; always connect to and to .+ + – –
6. Plug the connectors into their respective locations and tighten their
retaining screws. Reinstall the protective covers and tighten the gland
nuts to secure the wires.
7. To strain-relieve the wires, secure them to a hanger cable using the
tie-wraps provided.
WARNING!: Install the system in accordance
with local building codes and regulations. Some
jurisdictions may require additional suspension
points.
Use a licensed contractor or professional
engineer. QSC is not responsible for damages
that result from negligent installation of any
bracket, hanger, or loudspeaker.
— Figure 4 —
100
50
4Ω
25
12.5
25
50
100
N/A
4Ω
70
Volts
100
Volt
s
— Figure 6 —
AD-P.SUB
ACOUST IC DESIGN
PENDANT SUBWO OFER
INPUT: 70V, 100V, Z (4Ω)LOW-
MAXIMUM POWER RAT ING: 100 W RMS/200 W PROGRAM
HI-PASS FILTERED (200Hz-20kHz )
OUT PUT S 16Ω TEL LIT E SPEAKERSTO SA
SA SAT 1 T 2 SAT 3 T 4SA
— Figure 5 —
To
SA
T
1 T
o
SA
T 2 To SAT 3
(if needed)
To SAT 4
(if needed)
Amp
To other subwoofers
THRU
— Figure 7 —

Specyfikacje produktu

Marka: QSC
Kategoria: głośnik
Model: ADP-P.SUB

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z QSC ADP-P.SUB, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik QSC

QSC

QSC AD-DWL.180 Instrukcja

13 Września 2024
QSC

QSC SR-5152 Instrukcja

13 Września 2024
QSC

QSC SC-1120 Instrukcja

13 Września 2024
QSC

QSC AD-P6T Instrukcja

13 Września 2024
QSC

QSC GP218-sw Instrukcja

13 Września 2024
QSC

QSC AcousticDesign AD-C821 Instrukcja

13 Września 2024
QSC

QSC AD-S282H Instrukcja

13 Września 2024
QSC

QSC AcousticDesign AD-S.SAT Instrukcja

13 Września 2024
QSC

QSC K12 Instrukcja

13 Września 2024
QSC

QSC AD-DWL.SUB Instrukcja

12 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Harman Kardon

Harman Kardon Citation One Instrukcja

14 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024