Instrukcja obsługi QSC AD-S402T

QSC głośnik AD-S402T

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla QSC AD-S402T (4 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

1TD-001597-01-A

AD-S402T

Quick Start Guide

NOTE:

The AD-S402T is UL listed (1480A) for indoor use only

Installation

AD-S402T passive column loudspeaker systems require ampliﬁed audio signals. A pass-through on each loudspeaker permits connection to multiple loudspeakers.

The pluggable “Eurostyle” connectors allow the installer to pre-wire the audio system on site before the loudspeakers are installed.

TD-001597-01-A

*TD-001597-01*

The loudspeaker comes with a weather cover for the input cup to protect the input connections and switches from

precipitation and other weather hazards (Figure 1). Use the weather cover for all non-UL outdoor installations or any

applications where the loudspeaker may be exposed to moisture. To ensure a good seal in the cable gland, use outdoor-rated

cable with a round jacket between 5.5 mm and 9.4 mm in diameter.

To use the weather cover:

1. Loosen the nut on the cable gland.

2. Pass the cable all the way through the nut and the rest of the gland.

3. Attach the input connector to the wires (see

Input Connector

, below).

4. Once the loudspeaker enclosure is installed, plug the input connector into the loudspeaker's input cup. Secure the

connector to the loudspeaker using the two captive retaining screws, one on each end.

5. Make sure that the transformer tap selection switch is set properly.

6. Place the cover onto the loudspeaker's input cup and attach it using the four screws, lock washers, and ﬂat washers

provided.

7. Dress the cable so there is no undue strain on it. Tighten the gland nut until the grommet inside the gland has made a

tight seal onto the cable jacket.

Input Connector

AD-S402T Weather Cover

Diameter

up to

0.37 in

9.4 mm

— Figure 1 –

Strip wire

¼ in

6.3 mm

Up to

10 GAW

6 mm²



Turn screw fully

counterclockwise.



Insert wire fully.



Turn screw clockwise

to clamp wire tightly.

— Figure 2 –

INPUT

THRU To other

loudspeaker(s),

if necessary

— Figure 3 –

The pluggable “Eurostyle” input connector (Figure 2) has four terminals to facilitate connection on a distributed

line. It also allows the installer to pre-wire the venue before the loudspeakers themselves are installed. The

connector accommodates wire up to 10 AWG or 6 mm2. Be sure of proper and consistent polarity at each connector

(Figure 3). If one or more loudspeakers is out of polarity with others, the acoustic performance will suffer. Always

secure the connector to the loudspeaker using the retaining screws at both ends.

Mounting

Tilt/Swivel Bracket

The bracket provided with the loudspeaker allows 0, 5,

10, 15, and 20 degrees of downward tilt (Figure 4), and

up to ±55 degrees of horizontal panning (Figure 5).

These angles may be constrained by the loudspeaker

enclosure and adjacent walls or other structural elements.

In addition, the bracket can be inverted, which allows the

loudspeaker to be tilted up.

— Figure 4 –

— Figure 5 –

TD-001597-01-A

For mounting that requires no panning left or right, the bracket kit includes a zero-

pan locking screw to keep the loudspeaker securely in place.

The AD-S402T has three attachment locations for the bracket. Figure 6 shows their

center points, including distances from the bottom edge of the enclosure. Two M6 ×

20 screws with ﬂat washers are included for attaching the bracket to the rear panel of

the enclosure. Inverting the bracket offers three more conﬁgurations to choose from

and allows the loudspeaker to be tilted up instead of down (Figure 7). In addition,

the loudspeaker enclosure itself can be inverted, which doubles the total number of

mounting possibilities—exclusive of tilt—to 12.

An M6 eyebolt is included with the loudspeaker for attaching a safety tether, as may

be required by building codes in your jurisdiction. Attach the eyebolt securely to the

end mounting hole or to one of the unused ones.

The table below describes the pan range for different bracket positions and tilt angles.

AD-S402T Maximum Pan Range

Bracket

Position 0° tilt 5° tilt 10° tilt 15° tilt 20° tilt

Tilt bracket

removed

1 ±55° ±55° ±55° ±54° ±54° N/A

2 ±55° ±54° ±53° ±51° ±49° ±50°

3 ±55° ±51° ±46° ±40° ±32° ±50°

4 (1 inverted) ±55° ±45° ±29° ±7° N/A N/A

5 (2 inverted) ±55° ±46° ±33° ±15° N/A N/A

6 (3 inverted) ±55° ±50° ±43° ±33° ±22° ±50°

Attaching the wall piece

Attach the wall piece to the wall or other mounting surface. Figure 8 is a full-size

template. Consult a structural engineer for guidance in selecting mounting locations

and appropriate fasteners.

73.0 mm

2.88 in

Position 1 or

92.9 mm

3.66 in

150.9 mm

5.94 in

Position 2 or

Position 3 or

Eyebolt

position

— Figure 6 – — Figure 7 —

3.35 in

85.0 mm

5.30 in

134.5 mm

0.33 in

8.4 mm

×2

1.57 in

40.0 mm

Use 8 mm

or 5/16 in

screws

— Figure 8 —

NOTE:

To use Figure 8 as a template, print

this page at (i.e., with no scaling).actual size

3TD-001597-01-A

Attaching the loudspeaker bracket pieces to allow tilting

1. Select the appropriate attachment location for the bracket on the enclosure

rear panel. Note that because of the wall or mounting surface, in most cases

the lowest attachment location offers the widest range of tilt options, while

the highest offers few, if any, tilt options.

2. Use two M6×20 screws and their washers to secure the bracket to the

enclosure. Note that the bracket has four mounting holes; some attachment

locations use the long-spaced holes and some use the shorter ones.

NOTE: For convenience reasons we recommend conﬁguring the tilt angle

(Figure 9) before the loudspeaker and bracket are attached to the wall piece.

However, you can adjust the tilt later, even after the loudspeaker has been

installed.

3. Continue to Attaching the loudspeaker to the wall piece.

Attaching the loudspeaker bracket pieces for no-tilt

mounting

If the application does not require tilting the loudspeaker, you can either

conﬁgure it for 0 degrees or you can simplify the mounting bracket.

To simplify the mounting bracket, follow these steps

1. Omit these parts of the bracket kit, shown in Figure 10.

2. Attach this remaining part of the bracket directly to the loudspeaker enclosure

(see below left), using the two M6 × 20 screws (Figure 11).

3. Continue to Attaching the loudspeaker to the wall piece.

M5 × 42,

M4 × 9 shoulder screw

(2 places)

M4 ﬂange nut

(2 places)

20°

15°

10°

5°

0°

Zero-pan

lock screw

M8 stud, washer,

and cap nut

(2 places)

— Figure 9 –

— Figure 10 –

M6 × 20

— Figure 11 –

Attaching the loudspeaker to the wall piece

1. The wall piece has a stud on the top and the loudspeaker bracket piece has a stud on the bottom.

Set the hole in the loudspeaker bracket piece over the wall piece's stud and guide the loudspeaker

bracket's stud through the hole in the wall piece (Figure 12).

2. Set the loudspeaker onto the wall piece.

3. Install a washer and cap nut on each stud and tighten them ﬁnger tight.

4. Adjust the horizontal pan of the loudspeaker as needed.

5. If the loudspeaker's desired horizontal angle is perpendicular to the wall, you may install the zero-

pan locking screw to keep it from moving out of position. Make sure that the threaded hole in the

loudspeaker bracket piece lines up with the hole in the wall piece, then insert and tighten the screw.

6. Tighten the cap nuts securely.

— Figure 12 –

Specyfikacje produktu

Marka:	QSC
Kategoria:	głośnik
Model:	AD-S402T
Kolor produktu:	Biały
Materiał obudowy:	Aluminium
Wysokość produktu:	126.1 mm
Szerokość produktu:	131.3 mm
Głębokość produktu:	327.5 mm
Waga produktu:	3400 g
Szerokość opakowania:	310 mm
Wysokość opakowania:	244 mm
Głębokość opakowania:	544 mm
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS
Rekomendowane użycie:	Dom
Technologia łączności:	Przewodowa
Impedancja:	16 Ω
Moc wyjściowa (RMS):	60 W
Certyfikaty:	EASE, CLF, CAD, BIM
Zakres temperatur (eksploatacja):	-20 - 50 °C
Kanały wyjścia audio:	- kan.
Waga wraz z opakowaniem:	5000 g
Stopień ochrony IP:	IP54
Zasięg częstotliwości:	110 - 20000 Hz
Rozmieszczenie głośników:	Surface-mountable, Wall-mountable
Ilość przetworników:	4
Głośnik niskotonowy:	Tak
Średnica sterownika:	69.8 mm
Czułość:	85 dB
Typ głośnika:	Pełny zasięg
Uchwyty mocowania dołączone:	Tak
Zgodność z zasadami zrównoważonego rozwoju:	Tak
Liczba głośników niskotonowych:	4
Maksymalny poziom natężenia dźwięku:	111 dB
Rekomendowana moc wzmacniacza (maks):	120 W