Instrukcja obsługi QSC AcousticPerformance AP-4122m

QSC głośnik AcousticPerformance AP-4122m

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla QSC AcousticPerformance AP-4122m (4 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

Input Configuration Trapezoid Models

AcousticPerformance™ Series

Quick Start Guide

AcousticPerformance trapezoid models have the ability to switch between Passive and Bi-amp modes. Look at the Setting ports, below the input

connectors, to determine the current mode.

Yellow in the Setting port indicates the current mode.

Refer toFigure 1 and Figure 2

Note: The default mode is PASSIVE

– Figure 1 –

– Figure 2 –

– Figure 3 –

– Figure 4 –

Changing from Passive to Bi-amp mode

To change from Passive to Bi-amp or Bi-amp to Passive mode: Refer to Figure 3 and Figure 4.

1. Remove the six screws holding the input cup in place.

2. Remove the input cup, being careful not to place excess stress on the connecting wiring harness.

3. Remove the wiring harness plug from the receptacle at the bottom of the cup.

4. Insert the wiring harness plug into the desired mode receptacle at the bottom of the cup.

5. Turn the input cup over and verify that yellow is visible in the proper SETTING port. If not, move the plug to desired receptacle.

6. Carefully place the input cup back into position on the enclosure, being careful not to bind or pinch any of the wiring.

7. Secure the input cup with the six screws removed in step 1.

TD-000506-00-A

Passive mode Bi-Amp mode

Passive Mode

HPF

N/C

LPF LF

NL4 /

Barrier Strip

NL4 /

Barrier Strip

Bi-Amp Mode

1 -

2 -

Passive

Bi-Amp

TD-000506-00-A

Input Configuration Subwoofer Models

Wiring Examples

AcousticPerformance subwoofer (sw) models feature two NL4 connectors in a

crossed conguration. The subwoofers input uses pins 1+/-, leaving pins 2+/-

available for pass through to top boxes. The pass through output returns pins

2+/- back onto pins 1+/- for convenient cabling. A single NL4 cable may be

used for both sub and top box without the need for a custom turn cable. Refer

to Figure 6 and Figure 7.

Input Configuration Multipurpose Models

AcousticPerformance multipurpose (m) models feature two NL4 connectors

in parallel conguration for convenient pass through. For Bi-amp capable

models, LF is on pins 1+/- and HF on pins 2+/-. For passive fullrange

operation, ensure passive mode setting and use pins 1+/- with pins 2+/-

being available for pass through. Refer to Figure 5.

Ensure proper mode setting on Bi-amp capable models.

Passive models do not feature mode settings.

– Figure 7 –

– Figure 5 –

– Passive Models – – Bi-amp Models –

– Figure 6 –

– Subwoofer Models –

– Sub to Top –

MP CH1

SUB

AMP CH2

TOP

Sub Top

– Parallel Sub to Sub –

MP CH1

SUB

Sub 1 Sub 2

– Discrete Sub to Sub –

MP CH1

SUB 1

AMP CH2

SUB 2

Sub 1 Sub 2

3TD-000506-00-A

Using Yoke Mounts

AcousticPerformance Loudspeakers can be installed using a yoke mount

attached to the M10 Integrated Suspension Points. A 6 mm hex key is

required.

• Model AP-5102 (10") uses the AP-YM10 Yoke Mount

• Model AP-5122 (12") uses the AP-YM12 Yoke Mount

• Model AP-5122m (12" multi-purpose) uses the AP-YM12m

YokeMount

• Model AP-4122m (12" multi-purpose coaxial) uses the AP-YM12m

Yoke Mount

NOTE:

The multi-purpose models mount perpendicular to

the yoke. RefertoFigure 2.

WARNING!:

Consult a structural engineer before mounting the Yoke Mounts to any surface. Be sure the surface

can support the weight of the loudspeaker, and that the proper bolts are used to secure the yoke to the surface.

1. Properly secure the yoke mount bracket to the selected surface.

2. Refer to Figure 1 and Figure 2

3. Remove the center M10 hex plugs from the top and bottom of the loudspeaker

enclosure. You may discard or recycle the plugs.

4. Using proper lifting techniques place the loudspeaker in the yoke with the two

circular pads between the top and bottom of the loudspeaker enclosure and

theyoke.

5. Install the M10 socket head cap screw, lock washer, and at washer through the

yoke and pad, and into the Integrated Suspension point. Repeat for the other end

of the loudspeaker enclosure. Do not fully tighten the screws at this point.

6. Adjust the angle of the loudspeaker as required.

7. To prevent rattling with installation models in a vertical orientation, install the

two rectangular pads between the loudspeaker enclosure and the yokemount.

8. Torque the M10 cap screws to 60 in/lbs.

NOTE:

If you reposition the loudspeaker be sure to check that the

rectangular pads are in the proper positions.

M10 Cap Screw

Pads

Hex Plug

Split Washer

Washer

– Figure 2 –

M10 Cap Screw

Pads

Hex Plug

Split Washer

Washer

– Figure 1 –

Specyfikacje produktu

Marka:	QSC
Kategoria:	głośnik
Model:	AcousticPerformance AP-4122m
Kolor produktu:	Czarny
Wysokość produktu:	510 mm
Szerokość produktu:	385 mm
Głębokość produktu:	370 mm
Waga produktu:	18100 g
Ilość na paczkę:	1 szt.
Rekomendowane użycie:	Uniwersalne
Technologia łączności:	Przewodowa
Bluetooth:	Nie
Impedancja:	4 Ω
Moc wyjściowa (RMS):	325 W
Kanały wyjścia audio:	- kan.
Rodzaj opakowania:	Pudełko
Stosunek sygnału do szumu:	127 dB
Zasięg częstotliwości:	55 - 20000 Hz
Rozmieszczenie głośników:	Podłoga
Średnica sterownika:	305 mm
Czułość:	96 dB