Instrukcja obsługi Pyle PS1000

Pyle odbiornik PS1000

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pyle PS1000 (5 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/5
Stage & Studio Power Sequence Conditioner
PS1000 - PS1200
Pro Audio AV Digital Power Sequencer Controller
with Voltage & Temperature Readout, Rack Mount
www.PyleUSA.com
1www.PyleUSA.com 2
CAUTION!
RISK OF ELECTRIC SHOCK. DO NOT OPEN
TO PREVENT ELECTRIC SHOCK DO NOT REMOVE TOP OR BOTTOM COVERS.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DISCONNECT POWER CORD BEFORE REMOVING BACK PANEL COVER
TO ACCESS GAIN SWITCH.
WARNING!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
MAGNETIC FIELD
CAUTION! Do not locate sensitive high-gain equipment such as preampliers or
tape decks directly above or below the unit. Because this amplier has a high
power density, it has a strong magnetic eld which can induce hum into
unshielded devices that are located nearby. The eld is strongest just above and
below the unit. If an equipment rack is used, we recommend locating the
amplier(s) in the bottom of the rack and the preamplier or other sensitive
equipment at the top.
WATCH FOR THESE SYMBOLS:
The exclamation point triangle is used to alert the user
to important operating or maintenance instructions.
The lightning bolt triangle is used to alert the user to
the risk of electric shock.
Introduction & Features
This amazing professional audio processor has a built-in high performance Micro
Controller for precise electrical timing. This unit provides clean lters AC power
with built in two stage EMI lter for each output. 8 channel cut-switch rear panel
American Standard outputs and 1 constant un-switched front panel.
Other voltage outputs: 1 DC 12 Volt. You can link more than 100 units together
with automatic master unit display. The display shows AC voltage, ambient
temperature, wiring and ground status all in real time. 8 Segment display for
step Time and various LEDs cover output, master, bypass, power, voltage and
sequence.
Front Panel Introduction
1. Outlet Sequence Power ON/OFF: Push up or down to start the sequence
switch or automatically one by one.ON OFF
2. LED For Sequence Power ON/OFF
3. DISPLAY WINDOW: Displays voltage or temperature (both in Fahrenheit &
Centigrade)
4. Temperature: Adjust the temperature slightly if the real display is dierent
from the real one.
5. Mode Select: Button switch for Fahrenheit/Centigrade temperature or
Voltage display on the LED window.
6. BYPASS Switch: Push to make all the outlets work at one time. Can't be
adjusted by other control.
7. CH 1 Only: After starting the power sequence, control only the Ch1 or ON OFF.
8. One touch key and LED: ON/OFF Press to power . The LED indicates ON/OFF
the related outlet's status.
9. Choose the internal power sequence delay Internal delay time selector:
time: 0.5 seconds or 2 seconds.
10. USB Charge (5V/2A): Charge for Mobile phone (5VI2A) each.
11. Power switch for the assistance light: Power the light according to ON/OFF
the switch position.
12. Assistance light connector: BNC This is connector, it can supply 12V/0.5A
power, use a gooseneck light to connect.
13. Always Power Outlet: Assistant power outlet, connects to the AC input
directly, power always valid.
Rear Panel Introduction
1. Main power supply with standard American plug
2. Input Voltage Selective: Power Supply Switch at 115V/60Hz or 230V/50Hz
3. Power outlet can carry 15AMP (RMS) each outlet, Outlets OUT1-OUT8:
otherwise the unit is not safe.
4. Remote Control link: You can set a extra switch to replace the power switch
to achieve the long distance control.
5. LED for remote control: Indicates the unit status, use it with Remote control.
6. Many unit works via link, if you want to link next unit, the lower unit Link out:
should be connected here.
7. Many unit works via link, if you need to link up, then the upper unit Link in:
should be connected here.
www.PyleUSA.com
3www.PyleUSA.com 4
BlOCK DIAGRAM
Filter Schematic Diagram

Specyfikacje produktu

Marka: Pyle
Kategoria: odbiornik
Model: PS1000

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Pyle PS1000, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odbiornik Pyle

Pyle

Pyle Pro PTAU23 Instrukcja

8 Października 2024
Pyle

Pyle PLAM2001D Instrukcja

2 Października 2024
Pyle

Pyle PT1100 Instrukcja

2 Października 2024
Pyle

Pyle PFA100 Instrukcja

2 Października 2024
Pyle

Pyle PDA35BT Instrukcja

2 Października 2024
Pyle

Pyle PLA2200 Instrukcja

30 Września 2024
Pyle

Pyle PHDA6BT Instrukcja

29 Września 2024
Pyle

Pyle PDA77BU Instrukcja

29 Września 2024
Pyle

Pyle PT865BT Instrukcja

29 Września 2024
Pyle

Pyle PWMA3003BT Instrukcja

21 Września 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Denon

Denon AVR-S900W Instrukcja

15 Października 2024
Pro-Ject

Pro-Ject Amp Box DS2 Instrukcja

15 Października 2024
AKG

AKG HP12U Instrukcja

15 Października 2024
Apart

Apart SBR160 Instrukcja

14 Października 2024
American Audio

American Audio VLP 600 Instrukcja

14 Października 2024
Chord

Chord Anni Instrukcja

14 Października 2024
Sennheiser

Sennheiser EM 9046 SU Instrukcja

14 Października 2024
Yamaha

Yamaha MusicCast RX-V481 Instrukcja

13 Października 2024
JL Audio

JL Audio VX600/6i Instrukcja

12 Października 2024
Pioneer

Pioneer SX-303RDS Instrukcja

10 Października 2024