Instrukcja obsługi Pyle PLUTV58BKA

Pyle odbiornik PLUTV58BKA

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pyle PLUTV58BKA (15 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/15
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
+ 2 Ch. Rated Amplifier +Wireless BT Audio Controller
ATV, UTV, 4x4, Jeep, Wired RCA, for Boat Stereo Speaker
and Other Watercraft (1000W)
PRECAUTIONS
• This unit is designed for negative ground 12-14.50 Volts (DC) operation only.
• Use speakers with an impedance of 4 Ohms
• Avoid installing the unit where:
• It would be subject to high temperatures, such as from direct sunlight or hot air
from the heater.
• It would be exposed to rain or moisture.
• It would be subject to dust or dirt.
• If your vehicle or boat is parked in direct sunlight and there is a considerable
rise in temperature inside the car, allow the unit to cool off before operation.
• When installing the unit horizontally, be sure not to cover the heatsink ns with
the oor carpet.
• If this unit is placed too close to the resources radio, an interference may occur.
In this case, separate the amplier from the car radio.
• This power amplier employs a protection circuit to protect the transistors and
speakers if the amplier malfunctions. Do not attempt to test the protection
circuits by covering the heatsink or connecting improper loads.
• Do not use the unit with a weak auto battery as its optimum performance
depends on a normal battery supply voltage.
• For safety reasons, keep the volume of your audio system moderate so that you
can still hear normal traffic sounds in a reasonable distance.
WIRING INSTRUCTIONS
POWER CONNECTION
The battery terminal (BATT) must be connected directly to the positive terminal of
the vehicle battery to provide an adequate voltage source and minimize noise.
Connecting the battery terminal lead to any other point (such as the fuse block) will
reduce the power output and may cause noise and distortion. Use only #12 gauge or
thicker (smaller gauge #) wire for this lead and connect it to the terminal of the
battery after all other wiring is completed.
GROUND CONNECTION
The ground terminal (GND) connection is also critical to the correct operation of the
amplier. Use a wire of the same gauge as the power connection (#8 or thicker) and
connect it between the ground terminal (GND) of the amplier and a metal part of
the vehicle close to the mounting location. This wire should be as short as possible
and any paint or rust at the grounding point should be scraped away to provide a
clean metal surface to which the end of the ground wire can be screwed or bolted.
REMOTE TURN-ON CONNECTION
The amplier is turned on by applying +12V to the remote turn-on terminal (REM).
The wire lead to this terminal should be connected to the "Auto-Antenna" lead from
the vehicle/or boat stereo resources which will provide the +12V only when the
stereo resources is turned on. If the car stereo does not provide an "Auto-Antenna"
lead, the remote turn-on lead may be wired to an "Accessory" or "Radio" terminal in
the vehicle’s/or boat’s fuse block. This will turn the amplier on and off with the
ignition key, regardless of whether the stereo resources is on or off.
The remote turn-on lead does not carry large currents. So #16 gauge wire may be
used for this application.
SPEAKER CONNECTIONS
Depending on the type and number of speakers used with the amplier wire them
to the speaker terminals as per the appropriate wiring diagram. For most applications
#18 gauge wire should be used for the speaker leads but in no case thinner than
#16 gauge. For leads is excess of 10 feet #12 gauge is recommended. When wiring
the speakers, pay careful attention to the polarity of the terminals on the speakers
and make certain they correspond to the polarity of the corresponding terminals on
the amplier. Do not ground any speaker leads to the chassis of the vehicle/or boat.
OPERATION
After the amplier has been installed and all connections have been made carefully
and securely, turn the radio on so that the amplier is switched on automatically.
After a short power-on period, the amplier reaches its full performance. Now turn
up the volume slowly using the volume control of the radio. If there is no sound or
only a distorted replay, switch off the radio immediately - the amplier will also
switch off automatically - and check if all connections have been made correctly.
GND (-) = GROUND CONNECTION
Connect the GND terminal to the chassis ground of your vehicle/or boat and take
care of best electric and mechanic contact. In doing so, drill a hole into the vehicle/or
boat chassis near the amplier then remove color, dirt or any other substance from
the ground point. Thereafter fasten the cable end with added ring terminal by using
a screw. Ensure that the ground connection is as short as possible and that the cable
diameter is sufficient (min 4mm). Route the ground cables from the radio and all
other equipment parts, like equalizer, active crossover network or other ampliers, to
the same ground point.
www.PyleUSA.com
2www.PyleUSA.com 3

Specyfikacje produktu

Marka: Pyle
Kategoria: odbiornik
Model: PLUTV58BKA

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Pyle PLUTV58BKA, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odbiornik Pyle

Pyle

Pyle Pro PTAU23 Instrukcja

8 Października 2024
Pyle

Pyle PLAM2001D Instrukcja

2 Października 2024
Pyle

Pyle PT1100 Instrukcja

2 Października 2024
Pyle

Pyle PFA100 Instrukcja

2 Października 2024
Pyle

Pyle PDA35BT Instrukcja

2 Października 2024
Pyle

Pyle PLA2200 Instrukcja

30 Września 2024
Pyle

Pyle PHDA6BT Instrukcja

29 Września 2024
Pyle

Pyle PDA77BU Instrukcja

29 Września 2024
Pyle

Pyle PT865BT Instrukcja

29 Września 2024
Pyle

Pyle PWMA3003BT Instrukcja

21 Września 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Denon

Denon AVR-S900W Instrukcja

15 Października 2024
Pro-Ject

Pro-Ject Amp Box DS2 Instrukcja

15 Października 2024
AKG

AKG HP12U Instrukcja

15 Października 2024
Apart

Apart SBR160 Instrukcja

14 Października 2024
American Audio

American Audio VLP 600 Instrukcja

14 Października 2024
Chord

Chord Anni Instrukcja

14 Października 2024
Sennheiser

Sennheiser EM 9046 SU Instrukcja

14 Października 2024
Yamaha

Yamaha MusicCast RX-V481 Instrukcja

13 Października 2024
JL Audio

JL Audio VX600/6i Instrukcja

12 Października 2024
Pioneer

Pioneer SX-303RDS Instrukcja

10 Października 2024