Instrukcja obsługi Pyle PLUTV471AR

Pyle głośnik PLUTV471AR

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pyle PLUTV471AR (12 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 28 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
4’’ Waterproof Rated Off-Road Speakers
800 Watt Compact PowerSport Vehicle Speaker System
for ATV, UTV, 4x4, Jeep with RGB Lights
and Remote Control (2 Pair)
PLUTV471AR
www.PyleUSA.com
2www.PyleUSA.com 3
PRECAUTIONS
• This unit is designed for negative ground 12-14.50 Volts (DC) operation only.
• Use speakers with an impedance of 4 Ohms
• Avoid installing the unit where:
• It would be subject to high temperatures, such as from direct sunlight or hot air
from the heater.
• It would be exposed to rain or moisture.
• It would be subject to dust or dirt.
• If your vehicle or boat is parked in direct sunlight and there is a considerable rise
in temperature inside the car, allow the unit to cool off before operation.
• When installing the unit horizontally, be sure not to cover the heatsink ns with
the oor carpet.
• If this unit is placed too close to the resources radio, an interference may occur.
In this case, separate the amplier from the car radio.
• This power amplier employs a protection circuit to protect the transistors and
speakers if the amplier malfunctions. Do not attempt to test the protection
circuits by covering the heatsink or connecting improper loads.
• Do not use the unit with a weak auto battery as its optimum performance depends
on a normal battery supply voltage.
• For safety reasons, keep the volume of your audio system moderate so that you
can still hear normal traffic sounds in a reasonable distance.
WIRING INSTRUCTIONS
POWER CONNECTION
The battery terminal (BATT ) must be connected directly to the positive terminal
of the vehicle battery to provide an adequate voltage source and minimize noise.
Connecting the battery terminal lead to any other point (such as the fuse block)
will reduce the power output and may cause noise and distortion. Use only #12
gauge or thicker (smaller gauge #) wire for this lead and connect it to the terminal
of the battery after all other wiring is completed.
GROUND CONNECTION
The ground terminal (GND) connection is also critical to the correct operation of
the amplier. Use a wire of the same gauge as the power connection (#8 or thicker)
and connect it between the ground terminal (GND) of the amplier and a metal
part of the vehicle close to the mounting location. This wire should be as short as
possible and any paint or rust at the grounding point should be scraped away to
provide a clean metal surface to which the end of the ground wire can be screwed
or bolted.
REMOTE TURN-ON CONNECTION
The amplier is turned on by applying +12V to the remote turn-on terminal (REM).
The wire lead to this terminal should be connected to the "Auto-Antenna" lead from
the vehicle/or boat stereo resources which will provide the +12V only when the
stereo resources is turned on. If the car stereo does not provide an "Auto-Antenna"
lead, the remote turn-on lead may be wired to an "Accessory Radio" or " " terminal
in the vehicle’s/or boat’s fuse block. This will turn the amplier on and off with the
ignition key, regardless of whether the stereo resources is on or off.
The remote turn-on lead does not carry large currents. So #16 gauge wire may be
used for this application.
SPEAKER CONNECTIONS
Depending on the type and number of speakers used with the amplier wire them
to the speaker terminals as per the appropriate wiring diagram. For most applications
#18 gauge wire should be used for the speaker leads but in no case thinner than
#16 gauge. For leads is excess of 10 feet #12 gauge is recommended. When wiring
the speakers, pay careful attention to the polarity of the terminals on the speakers
and make certain they correspond to the polarity of the corresponding terminals
on the amplier. Do not ground any speaker leads to the chassis of the vehicle/or
boat.
OPERATION
After the amplier has been installed and all connectios have been made carefully
and securely, turn the radio on so that the amplier is switched on automatically.
After a short power-on period, the amplier reaches its full performance.
Now turn up the volume slowly using the volume control of the radio. If there is
no sound or only a distorted replay, switch off the radio immediately - the amplier
will also switch off automatically - and check if all connections have been made
correctly.
GND (-) = GROUND CONNECTION
Connect the GND terminal to the chassis ground of your vehicle/or boat and take
care of best electric and mechanic contact. In doing so, drill a hole into the vehicle/
or boat chassis near the amplier then remove color, dirt or any other substance
from the ground point. Thereafter fasten the cable end with added ring terminal
by using a screw. Ensure that the ground connection is as short as possible and
that the cable diameter is sufficient (min 4mm). Route the ground cables from the
radio and all other equipment parts, like equalizer, active crossover network or
other ampliers, to the same ground point.

Specyfikacje produktu

Marka: Pyle
Kategoria: głośnik
Model: PLUTV471AR

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Pyle PLUTV471AR, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Pyle

Pyle

Pyle PLRGSW64BK Instrukcja

15 Stycznia 2025
Pyle

Pyle Cycle PLMCA40 Instrukcja

3 Stycznia 2025
Pyle

Pyle PDIC61RD Instrukcja

30 Grudnia 2025
Pyle

Pyle PDIC1681RD Instrukcja

6 Grudnia 2024
Pyle

Pyle PHSP6K Instrukcja

6 Grudnia 2024
Pyle

Pyle PDIW67 Instrukcja

6 Grudnia 2024
Pyle

Pyle PDIC60 Instrukcja

6 Grudnia 2024
Pyle

Pyle PLATV65BT Instrukcja

6 Grudnia 2024
Pyle

Pyle PDIC81RD Instrukcja

6 Grudnia 2024
Pyle

Pyle PDWR40W Instrukcja

6 Grudnia 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Bowers & Wilkins

Bowers & Wilkins LCR3 Instrukcja

15 Stycznia 2025
Hifonics

Hifonics Vulcan VX6.2E Instrukcja

15 Stycznia 2025
ION

ION Insta Sound Instrukcja

15 Stycznia 2025
Pure Acoustics

Pure Acoustics QBT-340 Instrukcja

15 Stycznia 2025
Yamaha

Yamaha WX-010 Instrukcja

15 Stycznia 2025
Polk

Polk REACT SOUND BAR 1 Instrukcja

15 Stycznia 2025
Sennheiser

Sennheiser AMBEO Soundbar Plus SB02M Instrukcja

15 Stycznia 2025
Klipsch

Klipsch Reference RB-25 Instrukcja

15 Stycznia 2025
Klipsch

Klipsch Reference RB-35 Instrukcja

15 Stycznia 2025
Klipsch

Klipsch PIC-525-T-SC Instrukcja

15 Stycznia 2025