Instrukcja obsługi Pyle PLMTR4A

Pyle odbiornik PLMTR4A

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pyle PLMTR4A (2 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

4-Ch. Waterproof Rated Amplifier

Marine Grade PowerSport Amp for ATV,

UTV, 4x4, Jeep (1500 Watt)

PLMTR4A

www.PyleUSA.com www.PyleUSA.com www.PyleUSA.com

INTRODUCTION

This power amplier has been designed to provide high quality performance with a minimum of maintenance.

However, it's performance will only be as good as the care and quality of components with which is installed.

We therefore advise that you read these instructions very carefully to familiarize yourself with the product and

it's features. Before installing the power amplier please read this instruction manual carefully. The instructions

for mounting and connecting the set have to be followed precisely. If nec essary, a service center should be

consulted. All connections for DC power, signal input and speaker outputs can be carried out easily and safely

by way of RCA and screwed terminals.

INSTALLATION INSTRUCTIONS

Please choose a mounting place without any direct weather inuences. Note that the amplier generates heat

so that a well ventilated place is necessary. According to your vehicle's and marine boat's construction the set

can be made very carefully in order to ensure the amplier's full performance and reliability.

Keep the wire connections as short as possible with sucient dimensions in order to minimize power losses

and provide a higher audio output of the system. For safety reasons route all power and speaker wiring by

using the exiting wire channels. To minim ize damage to the cables, take care that they do not pass sharp

edged metal. Lay all cables as far away as possible from the ignition cables, modules in the boot and under the

key dashboard, as this create interference. Add a fuse into the (+) power cable in a distance of not more than 30

cm from the positive battery pole. Keep the length of the power wires as short as possible. It is better to use

power cables which are short and then longer speaker cables. In order to reduce interference, also pay

attention to the instructions.

PRECAUTIONS

• This unit is designed for negative ground 12-14.50 Volts (DC) operation only.

• Use speakers with an impedance of 4 Ohms

• Avoid installing the unit where:

• It would be subject to high temperatures, such as from direct sunlight or hot air from the heater.

• It would be exposed to rain or moisture.

1 2 3

• It would be subject to dust or dirt.

• If your vehicle or boat is parked in direct sunlight and there is a considerable rise in temperature inside the

car, allow the unit to cool o before operation.

• When installing the unit horizontally, be sure not to cover the heatsink ns with the oor carpet.

• If this unit is placed too close to the resources radio, an interference may occur. In this case, separate the

amplier from the car radio.

• This power amplier employs a protection circuit to protect the transistors and speakers if the amplier

malfunctions. Do not attempt to test the protection circuits by covering the heatsink or connecting improper

loads.

• Do not use the unit with a weak auto battery as its optimum performance depends on a normal battery

supply voltage.

• For safety reasons, keep the volume of your audio system moderate so that you can still hear normal trac

sounds in a reasonable distance.

WIRING INSTRUCTIONS

POWER CONNECTION

• The battery terminal (BATT) must be connected directly to the positive terminal of the vehicle battery to

provide an adequate voltage source and minimize noise. Connecting the battery terminal lead to any other

point (such as the fuse block) will reduce the power output and may cause noise and distortion. Use only #12

gauge or thicker (smaller gauge #) wire for this lead and connect it to the terminal of the battery after all other

wiring is completed.

GROUND CONNECTION

• The ground terminal (GND) connection is also critical to the correct operation of the amplier. Use a wire of

the same gauge as the power connection (#8 or thicker) and connect it between the ground terminal(GND) of

the amplier and a metal part of the vehicle close to the mounting location. This wire should be as short as

possible and any paint or rust at the grounding point should be scraped away to provide a clean metal

surface to which the end of the ground wire can be screwed or bolted.

REMOTE TURN-ON CONNECTION

• The amplier is turned on by applying +12V to the remote turn-on terminal (REM). The wire lead to this

terminal should be connected to the "Auto-Antenna" lead from the vehicle/or boat stereo resources which

will provide the +12V only when the stereo resources is turned on . If the car stereo does not provide an

"Auto-Antenna" lead, the remote turn-on lead may be wired to an "Accessory" or "Radio" terminal in the

vehicle's/or boat's fuse block. This will turn the amplier on and o with the ignition key, regardless of

whether the stereo resources is on or o. The remote turn-on lead does not carry large currents. So #16

gauge wire may be used for this application.

SPEAKER CONNECTIONS

• Depending on the type and number of speakers used with the amplier wire them to the speaker terminals

as per the appropriate wiring diagram. For most applications # 18 gauge wire should be used for the speaker

leads but in no case thinner than # 16 gauge. For leads is excess of 10 feet #12 gauge is recommended. When

wiring the speakers, pay careful attention to the polarity of the terminals on the speakers and make certain

they correspond to the polarity of the corresponding terminals on the amplier. Do not ground any speaker

leads to the chassis of the vehicle/or boat.

Features:

• Pro Audio PowerSport Amplier

• 4-Channel Audio Amp System

• Marine Grade Rugged Construction

• Waterproof Rated & Weather-Resistant Connectors

• Integrated Power Wiring Harness

• Perfect for Custom Installations & Applications

• Ability to Connect & Stream Audio from External Devices

• Wired Mini 3.5mm AUX Audio Input

• Speaker Wiring Connectivity

• Pre-Amp RCA Out to Any OEM /

Factory Made Universal

Mono Block/or Full Range Amplier

• Anti-Thump Turn-On

• Soft Turn On / O

• Overload & Power Protection Circuitry

• Used for Watercraft

& Portable Mobile Vehicle Sound Systems

www.PyleUSA.com

Technical Specs:

• Power Output: 1500 Watt MAX

• MAX Power: 4 x 375 Watt @ 4 Ohm (4 x 190 Watt)

• Marine Grade Waterproof Rating: IP-65

• T.H.D: 0.1%

• S/N Ratio : > 95 dB

• Channel Separation : > 65 dB

OPERATION

After the amplier has been installed and all connections have been made carefully and securely, turn the radio

on so that the amplier is switched on automatically. After a short power-on period, the amplier reaches its

full performance. Now turn up the volume slowly using the volume control of the radio. If there is no sound or

only a distorted replay, switch o the radio immediately - the amplier will also switch o automatically - and

check if all connections have been made correctly.

GND (-) = GROUND CONNECTION

• Connect the GND terminal to the chassis ground of your vehi cle/or boat and take care of best electric and

mechanic contact. In doing so, drill a hole into the vehicle/or boat chassis near the amplier then remove

color, dirt or any other substance from the ground point . Thereafter fasten the cable end with added ring

terminal by using a screw. Ensure that the ground connection is as short as possible and that the cable

diameter is sucient (min 4mm"). Route the ground cables from the radio and all other equipment parts, like

equalizer, active crossover network or other ampliers, to the same ground point.

+ 12V = POWER SUPPLY

• Connect the BATT te rminal to the positive pole of the battery with a lead cable and add a fuse into the power

cable in a distance of not more than 30 cm from the battery. The lead cable's diameter should be at least 4

mm' for a length of 3 m and 6 mm" for a length of 6 m.

REM (ON/OFF) REMOTE CONTROL

• Connect the REM terminal to the automatic antenna connector of your vehicle/or boat radio. Now when

turning on and o your vehicle/or boat radio. the amplier automatically switches ON and OFF.

A cable diameter of 0.5 mm² is sucient.

• Frequency Response : 10 - 40kHz

• Fuse: 10A

• Power: DC 12V

• Amp Dimensions (L x W x H):

5.90’’ x 3.62’’ x 1.97’’ -inches

• Sold as: 1

+CH1

-CH1

+CH2

-CH2

+CH3

-CH3

+CH4

-CH4

Green

Green+Black

Purple

Purple+Black

White

White+Black

Grey

Grey+Black

Speaker output

OUT

Black(AUX)

White (L)

Level Input/Output

OUT

Red (R)

+12V

GND

Red

Black

Power

REM

Blue

www.PyleUSA.com www.PyleUSA.com www.PyleUSA.com

POWER CONNECTION LEADS

NOTES ON THE POWER SUPPLY:

• Connect the +12V power input lead only after all other leads have been connected.

• Be sure to connect the ground wire of the unit securely to a metal part of the vehicle/or boat .

• A lose connection may cause a malfunction of the amplier.

6 7 8

• REM: The unit is turned on by applying +12 Volts to this terminal. This terminal does not draw heavy current

like the tow Power Terminals so a thinner connecting wire is acceptable. Standard 18 GAUGE is ne and the

standard color is red. If the radio is equipped with a Power Antenna control wire, it can drive this terminal.

If the Power Antenna wire is already in use, you can still splice into it. With this method, the unit will turn ON

automatically with the radio.

• Use the power supply lead with a fuse attached whose value is the same as original fuse.

• Place the fuse in the power supply lead as close as possible to the car battery.

• During a full power operation, Maximum current will run through the system. Therefore, make sure that the

leads to be connected to the +12V and GND terminals of the unit respectively must be larger than 18-Gauge

(AWG.18) proper Bridged operation. If only mono signal is available, a "Y" adapter is required.

FUSE REPLACEMENT

If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement,

there may be an internal malfunction. In this case, consult your dealer.

WARNING:

Use the specied amperage fuse. Use of a higher amperage fuse may cause serious damage.

PROTECTION CIRCUIT:

This amplier is provided with a protection circuit which operates in the following cases when:

• the unit is overheated.

• the speaker terminals are short circuited.

HOW TO PROCEED IN CASE OF FAULTS

No Function:

• The connection cable is not connected correctly (=terminal +12V/GND/REM).

Ensure that all connections and mechanic contact and that the jacket has been removed.

The fuse is defective-pay attention to the correct value of a new fuse!

No Sound:

• Speaker cable or speaker plug are not connected correctly.

• The plus and minus wires of the speaker cable have contact, thus eliminate the short circuit.

If you use Pay attention only 4 ohm load speaker is allowed.

No 2 ohm or less impedance speaker connection is allowed.

Poor Sound Quality (Distortions):

• The speakers are overloaded ,therefore turn down the volume level and check the volume control positions.

No Stereo Sound And A Weak Bass:

• Speaker cables (+) and (-) are mixed up, unit wired out of phase.

www.PyleUSA.com

SPEAKERS CONNECTIONS

+12V

BATTERY

DC 12V

To a metal part of car

HEAD UNIT

FUSE

(+12V)

SENS OUT

GND REM

GND

REM

Output (R)Output (L)

AUX Input

-CH1(White+Black)

+CH2(Grey)

-CH2(Grey )+Black

+CH3(Green

-CH3(Green )+Black

+CH4(Purple)

-CH4(Purple )+Black

BV Terminal

+CH1(White)

4 Ohms

CH1 Speaker

4 Ohms

CH2 Speaker

4 Ohms

CH3 Speaker

4 Ohms

CH4 Speaker

BV Terminal

www.PyleUSA.com

INTERFERENCE

All cables can source and create interference. The power cable and Cinch/RCA audio cable are very prone to

interference; the remote cables are less prone. There is often interference caused by the generator (piping),

ignition (cracking) or other vehicle/or boat electronic parts. Most of these problems can be eliminated by

correct and careful cabling. In doing so, here are the following guidelines:

• Use only a screened audio cable for the wiring between "low level in" of the amplier and RCA or DIN output

of the radio.

• Lay the signal, speaker and power cables separately with enough distance from one another and also from

each other car cable. If not possible, you can lay the circuit and ground cable together with the serial cables.

Audio and speaker cable should be as far away from these as possible. The REM cable to the automatic

antenna output of the radio can be laid together with the signal cables.

• Avoid ground loops by laying the ground wiring of all components to a center point in a star-like way.

You can nd the best central point in measuring the voltage directly at the battery. Now compare this voltage

value with the chosen ground point and the (+) terminal of the amplier. If measured voltage is only slightly

dierent, you've found the correct central. Otherwise you have to look for another point. You should measure

with the ignition point for earth being switched on and additionally switched on consumers (rear window

heating and light).

• If there are pickups from external electrical sources into the speaker cables, divide the core leads and twist

them together.

• If there are noises from the car electrics, add an interference suppression choke into the power wiring.

• If there are humming noises, use thicker ground cables or add further ground cables to the chassis.

• To reduce contact resistance and bad and loose contacts, please solder the cable ends or use multi core cable

ends, spade terminals or others. Gold Plated spade terminal are free of corrosion and have the lowest contact

resistance.

• Should all these meaures be without any success, the use of a ground loop isolator may solve the problem.

Specyfikacje produktu

Marka:	Pyle
Kategoria:	odbiornik
Model:	PLMTR4A

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Pyle PLMTR4A, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje odbiornik Pyle

Pyle PFMRA340BB.5 Instrukcja

13 Stycznia 2025

Pyle PLMRMBT5B Instrukcja

6 Grudnia 2024

Pyle P3001AT Instrukcja

6 Grudnia 2024

Pyle Pro PTAU23 Instrukcja

8 Października 2024

Pyle PLAM2001D Instrukcja

2 Października 2024

Pyle PT1100 Instrukcja

2 Października 2024

Pyle PFA100 Instrukcja

2 Października 2024

Pyle PDA35BT Instrukcja

2 Października 2024

Pyle PLA2200 Instrukcja

30 Września 2024

Pyle PHDA6BT Instrukcja

29 Września 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Marantz SR-8000 Instrukcja

15 Stycznia 2025

AKAI AM-32 Instrukcja

15 Stycznia 2025

Peavey CKd 608 Instrukcja

15 Stycznia 2025

OSD Audio Nero HTX4150 Instrukcja

14 Stycznia 2025

S.M.S.L PA200 Instrukcja

14 Stycznia 2025

Wavtech link700.4plus Instrukcja

13 Stycznia 2025

Behringer NU6000DSP Instrukcja

12 Stycznia 2025

Denon DRA-935R Instrukcja

12 Stycznia 2025

Kenwood KMM-BT508DAB Instrukcja

12 Stycznia 2025

Boss DD-500 Instrukcja

12 Stycznia 2025