Instrukcja obsługi Pyle PLMRA410BT

Pyle odbiornik PLMRA410BT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pyle PLMRA410BT (27 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/27
Elite Series Waterproof Amplifiers
Warnings
If the unit is likely to undergo excess vibration through use, your must properly install the unit securely. Damage
caused by insufficient support is not covered by the warranty. To prevent damage to the unit's panels, always
use protective plastic cups or washers before tightening mounting bolts.
PLEASE NOTE: Users must ensure that any type of smoke and related substances are not allowed to
enter the amplifier. Smokey air is corrosive and prolonged exposure will cause irreparable damage to
your amplifier. Take precaution before reconnecting to a power supply. Be aware that when any
equipment is taken from a cold to humid location, condensation may occur inside. Always allow time
for the equipment to attain the same temperature as its environment before reconnecting to a
power supply.
• Read these instructions and keep them for future reference.
• Carefully follow instructions and follow directions carefully.
• Keep the amplifier dry, as some liquids may contain minerals that corrode electronics circuitry.
• Clean amplifier housing only with a slightly damp cloth. No chemicals or solutions.
• Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions.
• Do not install near any heat source such as radiators, stoves, or other electrical devices that produce heat.
• Prevent any cables, wired or power cord from being walked on, bent, stretched or pinched, particularly at
the plug or at the point where connects to the amplifier.
• When uncertain about specifications, please first consult the Pyle Audio website and see the FAQs.
• Ensure this unit is placed on a stable and flat surface and can accommodate the weight of this unit.
• Unplug this unit during lightning storms or when it is unused for an extended period of time.
• Do not leave this device unattended when powered on.
• Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged
or malfunctions in any manner. This would include damage to he power supply cord or plug. t
Service may be obtained from an authorized Pyle Audio service center. Contact Pyle Audio and
make sure you have a receipt as proof of purchase along with the defective unit. You will be then
instructed to send or deliver the malfunctioning unit to an authorized center. They will handle the
necessary paperwork and repair. Remember to transport your unit in the original factory packaging.
Elite Series Waterproof Amplifiers
Testing & Connections
After all the connections have been made. turn on your stereo and listen for the
amplifier to turn on. If there are any unusual noises from the speakers then turn
the system off and recheck all the wiring.
After you have connected your radio or equalizer to the amplifier, you may adjust the gain
control to match the output level of your radio:
(A) Set the volume control on your radio to 2/3 position.
(B) Adjust the gain control for an average listening level.
(C) Turn the radio volume all the way down and listen for background noise.
(D) Start your vehicle and listen for electrical noise.
(E) Making fine adjustments to the sensitivity can reduce background noise and some
engine noise.
(F) CAUTION: Never turn the sensitivity up any farther than you need to get clear sound at
2/ 3 volume.
(G) This adjustment only needs to be made once.
NOTE: CARE MUST BE TAKEN AGAINST BATT - ERY OVER DISCHARGE CAUSED BY LONG OPERATION Of
THE SET AT A HIGH SOUND LEVEL WHEN THE ENGINE IS NOT RUNNING OR IDLING.
Maintenance
After all the connections have been made. turn on your stereo and listen for the amplifier
to turn on. If there are any unusual noises from the speakers then turn the system off and
recheck all the wiring.
Keep the amplifier dry. If it gets wet, wipe it dry immediately. liquids can contain minerals that corrode
electronic circuits.
Use the amplifier only in normal temperature environments. Temperature extremes of heat or cold
can shorten the life of electronic devices and distort or melt plastic parts.
Handle the amplifier gently and carefully. Dropping it can damage circuit boards and cases and can
cause the amplifier to work improperly.
Keep the amplifier away from dust and dirt. which can cause premature wear of parts.
Wipe the amplifier with a damp cloth occasionally to keep it looking new. Do not use harsh
chemicals, cleaning solvents, or strong detergents to clean the amplifier.

Specyfikacje produktu

Marka: Pyle
Kategoria: odbiornik
Model: PLMRA410BT

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Pyle PLMRA410BT, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odbiornik Pyle

Pyle

Pyle Pro PTAU23 Instrukcja

8 Października 2024
Pyle

Pyle PLAM2001D Instrukcja

2 Października 2024
Pyle

Pyle PT1100 Instrukcja

2 Października 2024
Pyle

Pyle PFA100 Instrukcja

2 Października 2024
Pyle

Pyle PDA35BT Instrukcja

2 Października 2024
Pyle

Pyle PLA2200 Instrukcja

30 Września 2024
Pyle

Pyle PHDA6BT Instrukcja

29 Września 2024
Pyle

Pyle PDA77BU Instrukcja

29 Września 2024
Pyle

Pyle PT865BT Instrukcja

29 Września 2024
Pyle

Pyle PWMA3003BT Instrukcja

21 Września 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Denon

Denon AVR-S900W Instrukcja

15 Października 2024
Pro-Ject

Pro-Ject Amp Box DS2 Instrukcja

15 Października 2024
AKG

AKG HP12U Instrukcja

15 Października 2024
Apart

Apart SBR160 Instrukcja

14 Października 2024
American Audio

American Audio VLP 600 Instrukcja

14 Października 2024
Chord

Chord Anni Instrukcja

14 Października 2024
Sennheiser

Sennheiser EM 9046 SU Instrukcja

14 Października 2024
Yamaha

Yamaha MusicCast RX-V481 Instrukcja

13 Października 2024
JL Audio

JL Audio VX600/6i Instrukcja

12 Października 2024
Pioneer

Pioneer SX-303RDS Instrukcja

10 Października 2024