Instrukcja obsługi Pyle PCT-40


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pyle PCT-40 (1 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/1
Enables quick convenient continuity cable
testing for all types of cables
LED's confirm each conductor continuity
and connection.
10 -way switch for selecting connections
to be tested. Also includes internal
battery and ground connection status
checks.
Rugged, compact, metal construction
for ultimate roadworthiness, long life,
and reliability.
Tests cables with all types of combinations
of the following connectors:
* USB
* 3. 5mm Jacks
* 6. 35mm Jacks
* 3-PIN XLR
* 5-PIN XLR
* RCA/Phono
* 3-PIN DIN
* 5- PIN DIN
* 8- PIN DIN
* 4-PIN S Type Jack
* RJ45
* 4-PIN SPEAKER
* 8 PIN SPEAKER
* 9V Alkaline Battery
Features:
At first, turn the rotary switch fully clockwise to test the battery strength.
The battery LED will light bright green if the internal battery is fully
charged.
Then plug one one end of the cable into the appropriate jack on the left
side panel of the cable tester. Plug the other end of the cable into the
appropriate jack on the right side panel. Set the rotary switch to"l" to
test the connection of contact l on the plug inserted in to the left side
panel.
If there is a connection, the Green LED willlight below "1" and a YELLOW
LED will light above each contact on the right side plug connected to "l"
on the left side plug. Use the charts below verify proper cable connections.
If no LED lights than there is no connection and the left side contact "1"
is "floating," due to design or an "open" in the cable.
Set the rotary switch to "2" to test contact 2, and so on, until all contacts
have been checked.
If the Ground LED lights than there is a connection between the
corresponding contacts and the chassis.
To test the cable with a banana plug, just plug each end of the cable
into the banana jacks: The LED will light and the unit will beep a tone
if there is connection between the plugs. These banana jacks can also
be used for continuity tests using two probe leads.
Cab/e testing:
Jack Speakon Phono
1 = sleeve l = -1 5 = -3 1 = screen
2 =tip 2 = +1 6 = -3 2 = hot
3 = ring 3 = -2 7 = -4
4 = +2 8 =+4
1 Sleeve Pin 1
2 Tip Pin 2
3 Ring Pin 3
1 Sleeve 1 Sleeve, 3 Ring
2 Tip 2 Tip
3 Ring 1 Sleeve, 3 Ring
1/4" TS Mono to 1/4" Mono
( Shorted with sleeve)
XLR unbalanced to XLR unbalanced
Pin 1 Pin 1, Pin 3
Pin 2 Pin 2
Pin 3 Pin 1, Pin 3
1 Sleeve 1 Sleeve
2 Tip 2 Tip
3 Ring 3 Ring
1 Sleeve Pin 1, Pin 3
2 Tip Pin 2
3 Ring Pin 1, Pin 3 (shorted
with sleeve)
1 / 4" TRS to 1/4" TRS
1/4" TS Mono to XLR unbalanced
XLR balanced to XLR balanced 1/4" TRS to XLR balanced
Pin 1 Pin 1
Pin 2 Pin 2
Pin 3 Pin 3


Specyfikacje produktu

Marka: Pyle
Kategoria: Niesklasyfikowane
Model: PCT-40

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Pyle PCT-40, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Pyle

Pyle

Pyle PDWM2950 Instrukcja

12 Stycznia 2025
Pyle

Pyle PVCLG85 Instrukcja

9 Stycznia 2025
Pyle

Pyle PDWR61BT Instrukcja

9 Stycznia 2025
Pyle

Pyle PSCBLKIT22 Instrukcja

1 Stycznia 2025
Pyle

Pyle PKST44W Instrukcja

6 Grudnia 2024
Pyle

Pyle PL2DN105 Instrukcja

6 Grudnia 2024
Pyle

Pyle PLCAPE50 Instrukcja

9 Października 2024
Pyle

Pyle PLCAPE60 Instrukcja

9 Października 2024
Pyle

Pyle PLCAPE32 Instrukcja

9 Października 2024
Pyle

Pyle PYG60 Instrukcja

7 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane