Instrukcja obsługi Projecta IDC25L

Projecta Ładowarka baterii IDC25L

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Projecta IDC25L (16 stron) w kategorii Ładowarka baterii. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/16
25 Amp, 5 Stage Switchmode
INTELLI-CHARGE
DC/SOLAR BATTERY CHARGER
P/No. IDC25L
2
WARNINGS
• Explosive gases may escape from the battery during charging.
Prevent flames and sparks and provide adequate ventilation
• Before charging, read the instructions
• FOR CHARGING 12 VOLT LITHIUM IRON PHOSPHATE BATTERIES ONLY
• Do not attempt to charge non-rechargeable batteries
• Never charge a frozen battery or when ambient temperature is below 0°C
• Corrosive and/or toxic substances may escape from the battery during charging and
damage delicate surfaces. Store and charge in a suitable area
• This appliance is not intended for use by young children or infirm persons unless they
have been adequately supervised by a responsible person to ensure that they can use
the appliance safely
• Young children should be supervised to ensure that they do not play with the
appliance
• Fit fuses as close to the batteries as possible to protect the cable in case of
short circuit
FEATURES
The IDC25L DC-DC charger is purposely designed for charging auxiliary batteries.
It includes all the features needed to maintain the auxiliary battery to its optimum
condition and to prolong the battery life.
SWITCHMODE TECHNOLOGY
The IDC25L converts your vehicle’s 12VDC/24VDC alternator power to the voltage
level allowing your batteries to be fully charged, prolonging battery life and
reliability. With the latest synchronous switching technology, efficiency of IDC25L
exceeds 94% at typical full load condition.
DUAL INPUT OPERATION
Allows two energy sources to power the IDC25L simultaneously. Solar input takes
precedence if solar and alternator inputs are present. When solar input cannot provide
enough energy to the load, the IDC25L will draw power from solar and alternator
simultaneously.
SOLAR MPPT
The IDC25L utilises sophisticated MPPT (Maximum Power Point Tracking) solar
regulator technology. MPPT maximises the power generated from the solar panels
to the auxiliary battery.
3
POWER SUPPLY (CONSTANT VOLTAGE OF 13.8 VOLTS)
This sets the charge in power supply mode giving a constant voltage of 13.8VDC.
This mode is best used where appliances are drawing power from the battery,
for example a fridge.
Power supply mode can also be used to reactivate a lithium iron phosphate battery
which is on internal low voltage disconnect mode. Currently, most high capacity
12V lithium iron phosphate batteries have an in-built battery management system
(BMS). When you discharge a 12V lithium iron phosphate battery to very low output
voltage, it will activate the battery’s internal low voltage disconnect protection –
the battery will be disconnected from the charger and load. However, in charge
mode, the IDC25L will only start charging if it detects the battery is connected.
To overcome this, set the IDC25L to power supply mode until the battery internal
low voltage disconnect protection is deactivated.
SUPERIOR 5 STAGE CHARGING
Using high speed microcontroller and proprietary charging algorithm, the IDC25L
delivers a sophisticated 5 stage charging process resulting in a faster and more
powerful charge, ideal for deep cycle batteries. The first two stages increase battery
life by gently starting to charge the battery at 5% and 25% of the bulk charge
respectively. The third stage, bulk (constant current), charges the battery much faster
while the fourth stage, absorption (constant voltage), ensures the battery is thoroughly
charged. The final stage, float, maintains the battery at a safe voltage allowing it to
be maintained and ready for use indefinitely.
IGNITION CONNECTION
The ignition connection activates the lower input voltage operation to suit vehicles
with smart (variable voltage) alternators.
TEMPERATURE COMPENSATION
The IDC25L is supplied with a 2 metre temperature sensor. The sensor monitors
the battery temperature and adjusts (compensates) the charger’s output to
prevent overcharging. This is ideal for batteries used in warmer/cooler climates or
environments.
REMOTE CHARGER STATUS INDICATION
A pink wire is provided for driving an external panel mount LED indicator (Eg Narva
P/No. 62090BL) to show the status of the charger. It shows whether the auxiliary
battery is on charge (Solid Colour) or the charger is in a fault condition (Flashing).

Specyfikacje produktu

Marka: Projecta
Kategoria: Ładowarka baterii
Model: IDC25L

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Projecta IDC25L, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Ładowarka baterii Projecta

Projecta

Projecta IC2500W Instrukcja

16 Września 2024
Projecta

Projecta BLT700 Instrukcja

13 Września 2024
Projecta

Projecta HDBC35 Instrukcja

5 Września 2024
Projecta

Projecta IC5000 Instrukcja

5 Września 2024
Projecta

Projecta HDBC20 Instrukcja

5 Września 2024
Projecta

Projecta HDBM4000 Instrukcja

5 Września 2024
Projecta

Projecta IC2500 Instrukcja

1 Września 2024
Projecta

Projecta PC2100 Instrukcja

1 Września 2024
Projecta

Projecta IC1500L Instrukcja

31 Sierpnia 2024
Projecta

Projecta IC1500 Instrukcja

29 Sierpnia 2024

Instrukcje Ładowarka baterii

Najnowsze instrukcje dla Ładowarka baterii

Graupner

Graupner Ultramat 12 Instrukcja

13 Stycznia 2025
Graupner

Graupner ULTRA DUO PLUS 30 Instrukcja

13 Stycznia 2025
Fuxtec

Fuxtec FX-E1LG1A Instrukcja

13 Stycznia 2025
Voltcraft

Voltcraft Charge Manager 410 Instrukcja

11 Stycznia 2025
Nitecore

Nitecore UHX1 PRO Instrukcja

11 Stycznia 2025
Envivo

Envivo ENV-1597 Instrukcja

11 Stycznia 2025
Xblitz

Xblitz XC1 Instrukcja

10 Stycznia 2025
Jackery

Jackery Explorer 240 v2 Instrukcja

7 Stycznia 2025
Jackery

Jackery Explorer 1000 v2 Instrukcja

7 Stycznia 2025
Schwaiger

Schwaiger LSET500 513 Instrukcja

7 Stycznia 2025