Instrukcja obsługi Planet WGS-803

Planet przełącznik WGS-803

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Planet WGS-803 (8 stron) w kategorii przełącznik. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 8-Port 10/100/1000T
Wall-mounted Gigabit Ethernet Switch, WGS-803.
Open the box of the WGS-803 Gigabit Ethernet Switch
and carefully unpack it. The box should contain the
following items:
zThe WGS-803 Gigabit Ethernet Switch x 1
zUser Manual x 1
zDIN-rail Kit x 1
zWall-mounted Kit x 1
zMagnet Kit x 1
z3-pin Terminal Block Connector x 1
zRJ45 Dust-proof Cap x 8
If any item is found missing or damaged, please contact
your local reseller for replacement.
2.1 Terminal Block Connector Pinouts
To install the 3-pin Terminal Block Connector on the
WGS-803, simply follow the following steps:
Step 1: Insert positive DC power wire into V+,
negative DC power wire into , and grounding V-
wire into Ground.
Step 2: Tighten the wire-clamp screws for preventing
the wires from loosening and plug into the
wall-mounted switch.
Note
1. The wire gauge should be in the range
from 12 to 24 AWG
2. The device must be grounded
3. The DC power input range is 12V ~ 48V DC
2.2 LED Indicators
System
LED Color Function
PWR Green Lights to indicate that the Switch has
power.
2.4 Physical Dimensions (WxDxH):
148 x 24.2 x 134mm
118.00
118.00
148.00 24.20
6.00
133.00
134.00
Dimensions ( unit = mm )
2.3 ProductSpecications
Model WGS-803
Hardware Specications
Network
Connector 8-port RJ45 for 10/100/1000BASE-T
MAC Address
Table
8K MAC address table with auto
learning function
Data Buffer 64Kbytes
Switch Fabric 16Gbps
Switch
Throughput 11.9Mpps@64bytes
Flow Control Back pressure for half duplex. IEEE
802.3x pause frame for full duplex
Power
Requirements 12~48V DC, 0.5A (max.)
Power
Consumption 6 watts/20BTU
ESD Protection 6KV DC
EFT Protection 6KV DC
Enclosure IP30 aluminum
2. Hardware Description
The front panel of the WGS-803 Gigabit Ethernet Switch
consists of 8 Auto-sensing 10/100/1000Mbps Ethernet
RJ45 Ports. The LED Indicators are also located on the
RJ45 ports of the Gigabit Ethernet Switch.
10/100/1000BASE-T RJ45 Port
10/100/1000BASE-T RJ45 Port
3-pin Terminal Block
DC Plug-in
10/100/1000BASE-T Interfaces
LED Color Function
LNK/
ACT Green
Lights
To indicate the link through
that port is successfully
established.
Blinks To indicate that the switch is
actively sending or receiving
data over that port.
1000 Green
Lights To indicate that the port is
operating at 1000Mbps.
Off If LNK/ACT LED is lit, it
indicates that the port is
operating at 10/100Mbps.
If LNK/ACT LED is Off, it
indicates that the port is link-
down.
3. Installation
3.1 Wall Mount Installation
To install the WGS-803 Gigabit Ethernet Switch on the
wall, simply follow the following steps:
Step 1: There are 4 holes with 8mm diameter on
the wall; the distance between the 2 holes is
133mm and the line through them must be
horizontal.
Step 2: Install a conductor pipe inside the board hole
and ush the edge of the conductor pipe with
the wall surface.
Step 3: Screw the bolts into the conductor pipe. The
WGS-803 is between bolts and conductor pipe,
as shown below.
Dimensions
(W x D x H) 148 x 24.2 x 134 mm
Weight 498g
Standard Conformance
Standard
Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3ab
IEEE 802.3x
Ethernet
Fast Ethernet
Gigabit Ethernet
Flow Control
Regulatory
Compliance FCC Part 15 Class A, CE
Environment
Operating
Temperature: -10 ~ 60 degrees C
Relative Humidity: 5 ~ 95%
(non-condensing)
Storage
Temperature: -20 ~ 70 degrees C
Relative Humidity: 5 ~ 95%
(non-condensing)
- 9 -
- 10 -
- 11 -
- 12 -
3.2 DIN-rail Mounting Installation
The DIN-rail kit is included in the WGS-803 package.
When the wall-mount application for the WGS-803
needs to be replaced with DIN-rail application, please
refer to the following gures to screw the DIN-rail on
the WGS-803. To hang up the WGS-803, follow the
steps below:
Step 1: Screw the DIN-rail on the WGS-803
3.3 Magnet Installation
To install the WGS-803 on a magnetic surface, simply
follow the following diagram:
Step 2: Lightly insert the bottom of DIN-rail into the
track
1Push
2Click
Step 3: Check whether the DIN-rail is tightly on the
track
4. Customer Support
Thank you for purchasing PLANET products. You can
browse our online FAQ resource and User’s Manual on
PLANET Web site rst to check if it could solve your
issue. If you need more support information, please
contact PLANET switch support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
support_switch@planet.com.tw
Copyright © PLANET Technology Corp. 2015.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All
other trademarks belong to their respective owners.
PLANET TECHNOLOGY CORPORATION
e-mail: sales@planet.com.tw http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
EC Declaration of Conformity
For the following equipment:
*Type of Product: Industrial 8-Port 10/100/1000T Wall-mount Switch
*Model Number: WGS-803
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.)
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive
on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
EN 55022 (2010)
EN 61000-3-2 (2006 + A2:2009)
EN 61000-3-3 (2008)
EN 55024 (2010)
EN 61000-4-2 (2009)
EN 61000-4-3 (2006 + A2:2010)
EN 61000-4-4 (2012)
EN 61000-4-5 (2006)
EN 61000-4-6 (2009)
EN 61000-4-8 (2010)
EN 61000-4-11 (2004)
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
(R.O.C.)
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Product Manager
Taiwan 28
th April, 2015
Place Date Legal Signature

Specyfikacje produktu

Marka: Planet
Kategoria: przełącznik
Model: WGS-803

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Planet WGS-803, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje przełącznik Planet

Planet

Planet IGTP-805AT Instrukcja

5 Października 2024
Planet

Planet IPM-16230 Instrukcja

5 Października 2024
Planet

Planet FSD-804P Instrukcja

5 Października 2024
Planet

Planet UPOE-1600G Instrukcja

3 Października 2024
Planet

Planet WS-1032P Instrukcja

3 Października 2024
Planet

Planet IPOE-162S Instrukcja

3 Października 2024
Planet

Planet IPOE-162 Instrukcja

3 Października 2024
Planet

Planet XGS3-24242 Instrukcja

3 Października 2024
Planet

Planet POE-171 Instrukcja

3 Października 2024
Planet

Planet POE-171A-95 Instrukcja

3 Października 2024

Instrukcje przełącznik

Najnowsze instrukcje dla przełącznik

Netgear

Netgear GS110TPP Instrukcja

15 Października 2024
ZyXEL

ZyXEL SFP-LHX1310-40-D Instrukcja

14 Października 2024
Tripp Lite

Tripp Lite B005-DPUA4 Instrukcja

11 Października 2024
Lancom

Lancom CS-8132F Instrukcja

9 Października 2024
Lancom

Lancom YS-7154CF Instrukcja

9 Października 2024
TP-Link

TP-Link Festa FS328G Instrukcja

9 Października 2024
Totolink

Totolink SW24DM Instrukcja

9 Października 2024
Totolink

Totolink SW1008P Instrukcja

9 Października 2024
Totolink

Totolink SW24G2 Instrukcja

9 Października 2024
Cudy

Cudy FS1006P Instrukcja

9 Października 2024