Instrukcja obsługi Planet POE-E101

Planet Wzmacniacz sygnału WiFi POE-E101

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Planet POE-E101 (4 stron) w kategorii Wzmacniacz sygnału WiFi. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
Introduction
1.1 Packet Contents
Thank you for purchasing PLANET POE-E101 IEEE
802.3af Power over Ethernet Extender, your Power
over Ethernet Extender package shall contains following
contents:
Check the contents of your package for following parts:
Power over Ethernet Extender x 1
User's Manual x 1
If any of these pieces are missing or damaged, please
contact your dealer immediately, if possible, retain the
carton including the original packing material, and use
them against to repack the product in case there is a
need to return it to us for repair.
1.3 TechnicalSpecication
Model POE-E101
Interfaces
LAN IN
1 x 10/100Base-TX Ethernet with IEEE
802.3af PoE “Data + DC” in Auto
MDI/MDI-X, Auto-negotiation RJ-45
connector
LAN OUT
1 x 10/100Base-TX Ethernet with IEEE
802.3af PoE “Data + DC” out Auto
MDI/MDI-X, Auto-negotiation RJ-45
connector
Power over Ethernet
PoE
Standard IEEE 802.3af Power over Ethernet
PoE Power
Supply Type Mid-Span / Type B
PoE Power
Output 48V DC, 270mA, Max. 13 Watts
Power Pin
Assignment 4/5(+), 7/8(-)
2.2 Ports Connection
IN Port
Connect the PoE IN port from following
802.3af PSE device through a CAT-5e/6
UTP cable:
• PoE Injector
• PoE Injector Hub
• PoE Ethernet Switch
• Previous POE-E101
OUT Port
Connect the PoE OUT port to following
802.3af PD device through a CAT-5e/6
UTP cable:
• PoE IP Camera
• PoE VoIP Phone
• PoE Wireless AP
• PoE Splitter
• Next POE-E101
2.3 LEDDenition:
LED Color Function
PoE IN Green Lights to indicate the port is
providing 48V DC in-line power.
LNK/
ACT Green
Lights
to
indicate
the
port
is link up.
Blink: indicate that the extender is
actively sending or receiving data
over port.IN
PoE
OUT Green Lights to indicate the port is
providing 48V DC in-line power.
Standards Conformance
Regulation
Compliance FCC Part 15 Class A, CE
Standard
Compliance
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 10/100Base-TX Fast
Ethernet
IEEE 802.3af Power over Ethernet PSE
/ Mid-Span
IEEE 802.3af Power over Ethernet PD /
Mid-Span
IEEE 802.3x Flow Control
Environment
Operating
Temperature:
0 ~ 50 Degree C
Relative Humidity:
0 ~ 95% (non-condensing)
Storage
Temperature:
-40 ~ 85 Degree C
Relative Humidity:
5 ~ 95% (non-condensing)
1.2 Key Features
Complies with IEEE 802.3af Power over Ethernet
Extends the range of PoE an additional 100 meters
(328ft.)
Forwards both Ethernet data and PoE power to
remote device
Auto-detect and protect of PoE equipment from being
damaged by incorrect installation
Multiple units, daisy-chain installation support
No external power cable installation required
Compact size, Wall-mountable design
Plug-and-Play installation
Hardware Specication
Data Rate 10/100Mbps
Switch
Architecture Store-and-Forward
Switch
Throughput 148810pps@64Bytes
Latency 7.840µs
Maximum
Frame Size 1552Bytes
Flow Control Back pressure for Half-Duplex
IEEE
802.3x
Pause
Frame
for
Full-Duplex
LED
Indicators
• 1 x PoE IN (Green)
• 1 x LAN Data (Green)
• 1 x PoE OUT (Green)
Protection ESD (Ethernet) : 6KV (TBD)
Surge (EFT for power) : 6KV (TBD)
Dimension
(W x D x H) 94 x 70 x 26 mm
Weight 215g
Power
Requirement
IEEE 802.3af compliant with voltage
within 44V-56V DC
Power
Consumption 2 Watts (system maximum)
Mechanical Metal / Wall Mountable
Cable TIA/EIA-568, Category 5/5e cable
Hardware Description
2.1 Product Outlook
Hardware Installation
This product provides two different running speeds –
10Mbps, 100Mbps in the same device and automatically
distinguishes the speed of incoming connection.
This section describes the hardware features of
POE-E101. Before connecting any network device to the
POE-E101, read this chapter carefully.
3.1 Before Installation
Before your installation, it is recommended to check
your network environment. If there is any far away IEEE
802.3af devices need to power on, the POE-E101 can
provide you a way to supply power for this Ethernet
device conveniently and easily.
The POE-E101 is installed between the PSE (Power Source
Equipment) and the PD (Powered Device); it is powered
by PSE and forwards the Ethernet data and remaining
POE power to the PD. The POE-E101 doesn’t require
an external power supply and it can be installed easily
just plug and play; that means the operator does not
need to congure the POE-E101. The POE-E101 injects
power to the PDs without affecting the data transmission
performance. It offers a cost effective and quick solution
to extend power and data an additional 100m.
Note
The POE-E101 can be installed with third-party
device if the device complied with IEEE 802.3af
standard.
- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
3.2 Connect POE-E101 to the Power Source
Equipment (PSE)
There are 2 RJ-45 ports in the PoE Extender, of which
the port functions as “IN” “PoE (Data and Power)
input" ”OUT” and the port on the other side functions
as “PoE (Data and Power) output”.
Step 1: Connect a standard CAT-5e/6 UTP cable from
Power Source Equipment (PSE), such as
PoE Switch, PoE Injector hub and single port
PoE injector, to the “IN” port of POE-E101.
Step 2: The PSE delivers both Ethernet Data and PoE
power over UTP cable to the POE-E101 and the
“PoE IN” LED will be steady on.
Note
1. The PoE IN LED turn on steady green means
POE-E101 is being powered successfully with
PoE class 0.
2. If PoE IN LED does not turn on, please check
the remote PSE or the cable with a PC or a
network device to see if the cable is correct.
Or with an 802.3af device such as the target
PD to check the power injection is correct
either.
3.4 Multiple PoE Extender Installation
The POE-E101 PoE Extender supports multiple units,
daisy-chain installation. They can be employed in
series for even longer distances based on remote
PoE IP Camera or PoE Wireless Access Point power
requirement.
Step 1: Connect the additional CAT-5e/6 cable from
the “OUT” port of the rst POE-101, the other
end of the UTP cable be used to connect to the
“IN” port of remote / next POE-E101.
Step 2: “PoE OUT” The LED indicator of the rst
POE-101 will be steady to shows it is providing
power to next PoE Extender.
Step 3: “PoE IN” The LED on the next POE-101 will
steady on.
Step 4: Connect the additional CAT-5e/6 cable to the
remote PoE powered device to the “OUT” port
of next or third POE-E101.
3.3 Connect POE-E101 to the Powered
Device (PD)
Step 3: Connect the additional CAT-5e/6 cable that
will be used to connect to the remote Powered
Device (PD) to the “OUT” port of POE-E101.
Step 4: The “OUT” port is also the power injectors
which transmit DC Voltage to the CAT-5e/6
cable and transfer data and power
simultaneously between the PSE and PD.
Step 5: Once POE-E101 detects the existence of an
IEEE 802.3af device, the “PoE OUT” LED
indicator will be steady, ON to shows it is
providing power.
PoE IP Camera PoE Injector
POE-E101
PoE Extender
PoE P oE
AC
100 meters100 meters
200 meters
DC
PoE
100Base-TX UTP with PoE
100Base-TX UTP
DC Power Line (DC)
Power Line (AC)
AC
Note
1. If the connected device is not fully complying
with IEEE 802.3af standard or in-line
power device, the PoE OUT LED indicator of
POE-E101 will not be steady on.
2. According to IEEE 802.3af standard, the
POE-E101 will not inject power to the cable
if not connecting to a standard IEEE 802.3af
device.
POE-E101
PoE Extender
PoE Ethernet Switch/
Injector Hub
PoE
PoE
PoE
PoE
PoE
PoE
PoE
100 meters100 meters100 meters
100 meters100 meters
PoE Access Point
PoE IP Camera
Non-PoE IP Camera
PoE Splitter
100 meters100 meters
DC
Power Output
300 meters 200 meters 100 meters 0 meters
AC
PoE
100Base-TX UTP with PoE
100Base-TX UTP
DC Power Line (DC)
Power Line (AC)
AC
POE-E101
PoE Extender
POE-E101
PoE Extender
POE-E101
PoE Extender
Note
1. Per POE-E101 will take 2 watts maximum
for the system itself, please check the total
power consumption of your 802.3af PD
and the POE-E101 before you make the
daisy-chain connection. If the overall power
consumption is overloaded, the local PSE
could shutdown the whole power system.
2. Per POE-E101 cable segment is limited in 100
meters CAT-5e/6 UTP wire from its IN/OUT
port to the other data end, use of any other
non standard cable or over distance could
results in unstable connection.
3.5 Optional - DIN-Rail mounting
There are two DIN-Rail holes on the left side of the
POE-E101 that allows the converter can be easily
installed with DIN-Rail mounting. The PLANET optional
DIN-Rail mounting Kit – RKE-DIN can be order
separately. When need to replace the wall mount
application with DIN-Rail application on the POE-E101,
please refer to following gures to screw the DIN-Rail on
the converter. To hang the POE-E101, follow the below
steps:
Step 1: screw the DIN-Rail on the POE-E101.
Step 2: Lightly press the button of DIN-Rail into the
track.
1
2
Step 3: Check the DIN-Rail is tightly on the track.
You must use the screws supplied with
the mounting brackets. Damage caused to
the parts by using incorrect screws would
invalidate your warranty.

Specyfikacje produktu

Marka: Planet
Kategoria: Wzmacniacz sygnału WiFi
Model: POE-E101

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Planet POE-E101, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Wzmacniacz sygnału WiFi Planet

Planet

Planet WNAP-1110 Instrukcja

10 Października 2024
Planet

Planet LRP-104CET Instrukcja

30 Września 2024
Planet

Planet POE-E201 Instrukcja

21 Września 2024
Planet

Planet IPOE-E202 Instrukcja

4 Września 2024
Planet

Planet VC-231G Instrukcja

30 Sierpnia 2024
Planet

Planet POE-E304 Instrukcja

20 Sierpnia 2024
Planet

Planet GRT-401 Instrukcja

20 Sierpnia 2024
Planet

Planet POE-E101 Instrukcja

13 Sierpnia 2024
Planet

Planet VC-234G Instrukcja

5 Lipca 2024

Instrukcje Wzmacniacz sygnału WiFi

Najnowsze instrukcje dla Wzmacniacz sygnału WiFi

Hawking Technologies

Hawking Technologies HOW2R1 Instrukcja

14 Października 2024
Netgear

Netgear WN2000RPTv2 Instrukcja

10 Października 2024
Xiaomi

Xiaomi RA75 Instrukcja

9 Października 2024
Cudy

Cudy RE3000 Instrukcja

8 Października 2024
Cudy

Cudy RE1200 Instrukcja

8 Października 2024
Netgear

Netgear EX6170 Instrukcja

8 Października 2024
Extron

Extron FOX 3G HD-SDI SM Instrukcja

8 Października 2024
Extron

Extron FOXBOX Rx VGA MM Instrukcja

8 Października 2024
Extron

Extron FOX 3G HD-SDI P SM Instrukcja

8 Października 2024
Extron

Extron FOXBOX Tx DVI Plus MM Instrukcja

8 Października 2024