Instrukcja obsługi Planet IGTP-815AT

Planet Niesklasyfikowane IGTP-815AT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Planet IGTP-815AT (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET compact industrial 100/1000X to
10/100/1000T 802.3at PoE+ Media Converter, IGTP-815AT. In the
following sections, the term “Industrial PoE+ Media Converter”
means the IGTP-815AT.
Open the box of the Industrial PoE+ Media Converter and carefully
unpack it. The box should contain the following items:
Industrial PoE+ Media
Converter x 1
User’s Manual x 1 Wall-mount Kit x 1
DIN-rail Kit RJ45 Dust Cap x 1 SFP Dust Cap x 1
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original
packing material, and use them again to repack the product in case
there is a need to return it to us for repair.
Power
Consumption
System ON without loading
DC 48V: 0.96W/3.27BTU
DC 56V: 1.12W/3.82BTU
Full loading with PoE
DC 48V: 35W/119BTU (PoE:30W)
DC 56V: 42W/143BTU (PoE:36W)
DIP Switch
O: LFP (Link Fault Passthrough) disable
On: LFP (Link Fault Passthrough) enable
FEF (Far End Fault) works with LFP to
prevent data loss
The DIP switch is turned o by default.
Enclosure IP30 metal case
Installation DIN-rail kit and wall-mount ear
ESD Protection 6KV DC
Cables
10/100/1000BASE-T:
2-pair UTP Cat. 3, 4, 5, 5e, 6
(maximum 100 meters)
EIA/TIA-568 100-ohm STP
(maximum 100 meters)
100BASE-FX/1000BASE-SX/LX:
Multi-mode: 50/125μm or 62.5/125μm
optical ber
Single-mode: 9/125μm optical ber
Power Over Ethernet
PoE Standard IEEE 802.3at Power over Ethernet Plus
PoE Power Output 48~56V DC: 36 watts max.
3.2 LEDDenition:
System
LED Color Function
PWR Green Lights to indicate the Industrial PoE+ Media
Converter has power.
Gigabit TP Interface
LED Color Function
TP
LNK/
ACT
Green
Lit: Indicates that the Copper Port is
successfully connecting to the network at
10/100/1000Mbps.
Blinks: Indicates the Copper Port is receiving
or sending data.
PoE-in-
Use Amber
Lit: Indicates that the port is providing PoE
power to remote powered device.
O: Indicates that the port is not providing
PoE power to remote powered device.
Gigabit Fiber Interface
LED Color Function
Fiber
LNK/
ACT
Green
Lit: Indicates that the ber optic port is
successfully connecting to the network at
100Mbps or 1000Mbps.
Blinks: Indicates the ber optic port is
receiving or sending data.
3.HardwareIntroduction
3.1 Three-ViewDiagram
The three-view diagram of the Industrial Media Converter PoE+
consists of Ethernet interfaces and one removable 2-pin terminal
block. The LED indicators are also located on the front panel.
104.00
30.00
70.00
18.00
9.00
91.00
52.00 52.00
50.00
30.00
21.69
28.65
20.00
28.00
48.80 40.00
18.00
40.00
18.00
Mounting Kit
Mounting Kit
DIN-Rail Kit
Unit: mm
Rear ViewSide View Side View
Top View
Front View
Bottom View
1 2
PWR
LFP
100/1000X
ONOFF
LNK/ACT
LNK/
ACT
PoE-in-Use
V+
PWR
DC I npu t:
48-56V
, 0 .9A max.
Figure1: IGTP-815AT Three-View Diagram
2.ProductSpecications
Model IGTP-815AT
Hardware Specications
Copper Port
10/100/1000BASE-T Ethernet TP interface.
Maximum 100m distance.
Auto-negotiation, auto MDI/MDI-X with PoE
injector function
SFP Port 1000BASE-SX/LX/BX SFP interface
Compatible with 100BASE-FX SFP
Flow Control
Back pressure for half duplex mode
IEEE 802.3x pause frame for full duplex
mode
Maximum Frame
Size 9K
LED
System: Power (green)
Fiber 100/1000BASE-X: LNK/ACT (green)
TP 10/100/1000BASE-T: LNK/ACT (green)
PoE: Power-in-use (Amber)
Dimensions
(W x D x H) 30 x 70 x 104 mm
Weight 231g
Power
Requirements
DC 48~56V, supports reverse polarity
protection
(>51V DC for PoE+ output recommended)
PoE Power Supply
Type End-span
Power Pin
Assignment 1/2(+), 3/6(-)
PoE Power Budget 36 watts
Standards Conformance
Regulatory
Compliance FCC Part 15 Class A, CE
Protocols and
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3z Gigabit Ethernet over Fiber
Optic
IEEE 802.3x Flow Control
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
Stability Testing
IEC60068-2-32 (free fall)
IEC60068-2-27 (shock)
IEC60068-2-6 (vibration)
Environment
Temperature Operating: -40~75 degrees C
Storage: -40~85 degrees C
Humidity Operating: 5~9 % (non-condensing)5
Storage: 5~9 % (non-condensing)5
Front View
PWR
LFP
100/1000X
ONOFF
LNK/ACT
LNK/
ACT
PoE-in-Use
Figure2: IGTP-815AT Front View
3.3 WiringthePowerInputs
The 2-contact terminal block connector on the top panel of
Industrial PoE+ Media Converter is used for 48~56V DC power
inputs. Please follow the steps below to insert the power wire.
Caution
When performing any of the procedures like inserting
the wires or tightening the wire-clamp screws, make
sure the power is OFF to prevent from getting an
electric shock.
1. Insert positive and negative DC power wires into contacts 1 and
2 for POWER.
V+
PWR
DC Input:
48-56V
, 0.9A max.
1 2
2. Tighten the wire-clamp screws for preventing the wires from
loosening.
Note
1. The wire gauge for the terminal block should be in
the range between 12 and 24 AWG.
2. The DC power input range is 48V ~ 56V DC.
- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
4.HardwareInstallation
This section describes the functionalities of the Industrial PoE+
Media Converter’s components and guides you to installing it on
the DIN rail and wall. Please read this chapter completely before
continuing.
Note
This following pictures guide you to installing the
device, and the device is not IGTP-815AT.
4.1 DIN-railMountingInstallation
2
1
4.4 GroundingtheDevice
User MUST complete grounding wired with the device; otherwise,
a sudden lightning could cause fatal damage to the device. EMD
(Lightning) DAMAGE IS NOT CONVERED UNDER WARRANTY.
V+
PWR
DC Input:
48-56V
, 0.9A max.
1 2
Earth Ground
4.2 Wall-mountPlateMounting
4.3 SideWall-mountPlateMounting
Caution
You must use the screws supplied with the wall-
mounting brackets. Damage caused to the parts by
using incorrect screws would invalidate your warranty.
5.FiberandPoEInstallation
The IGTP-815AT is exible enough to extend the distance from
220m to 120km. It depends on the 1000BASE-X or 100BASE-FX
SFP transceivers. The SFP transceivers are hot-pluggable and
hot-swappable. You can plug in and out the transceiver to/from any
SFP port without having to power down the Industrial 802.3at PoE+
Media Converter.
If there is any IEEE 802.3at/802.3af devices needed to power on,
the IGTP-815AT can provide you a way to supply power for this
Ethernet device conveniently and easily.
The IGTP-815AT needs DC 48-56V input and it injects the DC
power into the pin of the twisted pair cable (Pins 1, 2, 3 and 6).
DC
Power Line (DC)
1000BASE-SX/LX Fiber-optic
1000
PoE
1000BASE-T UTP with PoE
550m / 20km 100m
DC 48~56V
IGTP-815AT
DC
PowerData
Power
Data
PoE
IP Camera
PoE
Monitoring
Center
1000
Fiber Switch
6.LinkFaultPassthrough
The LFP function includes Link Loss Carry Forward (LLCF), Link
Loss Return (LLR) and the DIP switch design. LLCF and LLR can
immediately alert administrators about the issue of the link media
and provide ecient solution to monitor the network. The DIP
switch provides the disabling or enabling of the LFP function.
PoE
IP Camera
LFP
Enabled
LFP
Enabled
Copper Cable
PoE
Copper Cable
Monitoring Center
PoE
IP Camera
Fiber Cable
LFP
Enabled
LFP
Enabled
Copper Cable
PoE Po E
Copper Cable
Monitoring Center
Copper Link Broken
1
Copper
Link Down
5
LFP disconnects
Fiber Link
2
LFP disconnects
Copper Link
4
Fiber Link Down
3
1000
1000
Fiber Cable
Remote Link
B ro k e n
Remote Link
N o rm al
Note
LFP function is turned off by default. This feature
can also be turned on via the DIP switch. If you are
not familiar with the network installation and for
diagnostic purpose (i.e. check which end is broken),
you can turn it on. Otherwise, please keep it in the
default position.
CustomerSupport
Thank you for purchasing PLANET products. You can browse our
online FAQ resource on PLANET web site rst to check if it could
solve your issue. If you need more support information, please
contact PLANET switch support team.
PLANET online FAQs:
http://www.planet.com.tw/en/support/faq.php
Switch support team mail address:
support_switch@planet.com.tw
Copyright © PLANET Technology Corp. 2021
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.

Specyfikacje produktu

Marka: Planet
Kategoria: Niesklasyfikowane
Model: IGTP-815AT

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Planet IGTP-815AT, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Planet

Planet

Planet LS100-SMK Instrukcja

9 Października 2024
Planet

Planet IGS-1000-4UP2X Instrukcja

9 Października 2024
Planet

Planet NMS-AIoT Instrukcja

9 Października 2024
Planet

Planet NMS-ST Instrukcja

9 Października 2024
Planet

Planet IGS-R4215-24T4X Instrukcja

5 Października 2024
Planet

Planet IXT-900-2X1UP Instrukcja

4 Października 2024
Planet

Planet AVS-4210-24HP4X Instrukcja

4 Października 2024
Planet

Planet TSN-5225-4T Instrukcja

4 Października 2024
Planet

Planet MGB-LX Instrukcja

4 Października 2024
Planet

Planet ISW-514PTF Instrukcja

3 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024