Instrukcja obsługi Planet IGS-500T

Planet przełącznik IGS-500T

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Planet IGS-500T (4 stron) w kategorii przełącznik. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET compact industrial 5-port
10/100/1000T Gigabit Ethernet Switch, IGS-500T. In the following
section, the term means the “Industrial Gigabit Ethernet Switch”
IGS-500T.
Open the box of the Industrial Gigabit Ethernet Switch and carefully
unpack it. The box should contain the following items:
Industrial Gigabit Ethernet Switch x 1 User’s Manual x 1
Wall-mount Kit DIN-rail Kit
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a
need to return it to us for repair.
3. Product Specications
Model IGS-500T
Hardware Specications
Copper Ports 5 x 10/100/1000BASET RJ45 TP auto-MDI/
MDI-X, auto negotiation
Connector
Removable 6-pin terminal block
Pin 1/2 for Power 1; Pin 3/4 for fault alarm; Pin
5/6 for Power 2
Alarm Provides one relay output for power failure
Alarm relay current carry ability: 1A@DC 24V
LED
3 x LED for system and power:
Green: DC Power 1
Green: DC Power 2
Red: Power Fault
2 x LED for each copper port
Green: 1000Mbps LNK/ACT
Orange:10/100Mbps LNK/ACT
ESD Protection 6KV
EFT Protection 6KV
Power Requirements
12~48V DC, redundant power with polarity
reverse protection function, 24V AC power
support
Power Consumption
/ Dissipation 3.6 watts/12.35BTU
Installation DIN-rail kit and wall-mount ear
Enclosure IP30 metal case
Dimensions
(W x D x H) 70 x 104 x 30 mm
Weight 252g
LED Denition:
LED Color Function
P1 Green Lights to indicate power input 1 has power.
P2 Green Lights to indicate power input 2 has power.
Fault Red Lights to indicate that power 1 or power 2 has
failed.
1000
LNK/ACT Green
Lights: Indicating the port is running at
1000Mbps speed and successfully established.
Blinks: Indicating that the switch is actively
sending or receiving data over that port.
100
LNK/ACT Orange
Lights: Indicating the port is running at
10/100Mbps speed and successfully established.
Blinks: Indicating that the switch is actively
sending or receiving data over that port.
Top View:
1 2 3 4 5 6
Figure 3: IGS-500T Top View
4.2 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of Industrial
Gigabit Ethernet Switch is used for two DC redundant power inputs.
Please follow the steps below to insert the power wire.
4. Hardware Introduction
4.1 Three-View Diagram
The three-view diagram of the Industrial Gigabit Ethernet Switch
consists of ve auto-sensing 10/100/1000BASE-T RJ45 port and one
removable 6-pin terminal block. The LED indicators are also located
on the front panel.
18.00
9.00
91.00
52.00 52.00
104.00
30.00
50.00
30.00
70.00
21.69
28.65
Dimensions ( unit = mm )
Side View Front View Side View
Top View Bottom View
Rear View
P1 P2 FAULT
1
2
3
4
5
1000
100
ACTLNK
ACTLNK
Figure 1: IGS-500T Three-View Diagram
2. Product Features
Physical Port
5-port 10/100/1000BASE-T RJ45 with auto-MDI/MDI-X function
Layer 2 Features
Complies with IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX,
IEEE 802.3ab 1000BASE-T Ethernet standard
Supports auto-negotiation and 10/100Mbps half/full duplex and
1000Mbps full duplex
Prevents packet loss with back pressure (half-duplex) and IEEE
802.3x pause frame ow control (full-duplex)
High-performance Store and Forward architecture, broadcast storm
control and runt/CRC ltering eliminate erroneous packets to opti-
mize the network bandwidth
Backplane (switching fabric): 10Gbps
Integrated address look-up engine, supporting 4K absolute MAC
addresses
9K jumbo packet size
Automatic address learning and address aging
CSMA/CD Protocol
Industial Case and Installation
IP30 metal case
DIN rail and wall-mount design
12 to 48V DC, redundant power with polarity reverse protect func-
tion and connective, removable terminal block for master and slave
power; 24V AC power support
Supports 6000 VDC Ethernet ESD protection
-40 to 75 degrees C operating temperature
Free fall, shock-proof and vibration-proof for industries
Switch Specications
Switch Processing
Scheme Store-and-Forward
Address Table 4K entries
Buffer Memory 1M bits on-chip buffer memory
Flow Control Back pressure for half duplex
IEEE 802.3x pause frame for full duplex
Switch Fabric 10Gbps
Throughput
(packet per second) 7.4Mpps@64bytes
Jumbo Frame 9K
Network Cables
10/100/1000BASE-T
Cat. 3, 4, 5, 5e, 6 UTP cable (max. 100 meters)
EIA/TIA-568 100-ohm STP (max. 100 meters)
Standards Conformance
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3x Full-Duplex Flow Control
IEEE 802.3az Energy Efcient Ethernet
IEEE 802.1p Class of Service
Regulatory
Compliance FCC Part 15 Class A, CE
Stability Testing
IEC 60068-2-32 (free fall)
IEC 60068-2-27 (shock)
IEC 60068-2-6 (vibration)
Environment
Temperature Operating: -40~75 degrees C
Storage: -40~75 degrees C
Humidity Operating: 5~90%,
Storage: 5~90% (non-condensing)
Front View:
P1 P2 FAULT
1
2
3
4
5
1000
100
ACTLNK
ACTLNK
Figure 2: IGS-500T Front View
When performing any of the procedures like inserting the
wires or tightening the wire-clamp screws, make sure the
power is OFF to prevent from getting an electric shock.
1. Insert positive and negative DC power wires into contacts 1 and 2
for POWER 1, or contacts 5 and 6 for POWER 2.
1 2 3 4 5 6
2. Tighten the wire-clamp screws for preventing the wires from
loosening.
1 2 3 4 5 6
Power 1 Fault Power 2
+ - + -
Note
1. The wire gauge for the terminal block should be in the
range between 12 and 24 AWG.
2. The DC power input range is 12V ~ 48V DC and
supports 24V AC
3. Please just use one power input when using 24V AC.
- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
4.3 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block
connector as the picture shows below. Inserting the wires, the Industrial
Gigabit Ethernet Switch will detect the fault status of the power failure
and then forms an open circuit. The following illustration shows an
application example for wiring the fault alarm contacts.
123456
Fault Alarm Contacts
The Fault Alarm Contacts are
energized (CLOSE) for normal
operation and will OPEN when
failure occurs
Fault
Insert the wires into the fault alarm contacts
Note
1. The wire gauge for the terminal block should be in the
range between 12 and 24 AWG.
2. Alarm relay circuit accepts up to 24V DC,1A.
Step 2: Lightly insert the bottom of the switch into the track
1
2
Step 3: Make sure the DIN rail is tightly secured on the track.
Step 4: Please refer to the following procedure to remove the
Industrial Gigabit Ethernet Switch from the track.
1
2
Step 5: Lightly pull out the bottom of the switch for removing it from
the track.
5. Installation
This section describes the functionalities of the Industrial Gigabit
Ethernet Switch’s components and guides you to installing it on the DIN
rail and wall. Please read this chapter completely before continuing.
This following picture tells the user how to install the
device, and the device is not IGS-500T.
5.1 DIN-rail Mounting Installation
The DIN rail is screwed on the Industrial Gigabit Ethernet Switch when
out of factory. When replacing the wall-mount application with DIN-rail
application, Industrial Gigabit Ethernet Switch is needed. Please refer to
the following gures to screw the DIN rail on it. To hang the Industrial
Gigabit Ethernet Switch, follow the following steps:
Step 1: Screw the DIN rail on the Industrial Gigabit Ethernet Switch.
5.2 Wall-mount Plate Mounting
To install the Industrial Gigabit Ethernet Switch on the wall, please
follow the instructions described below.
Step 1: To remove the DIN rail from the Industrial Gigabit Ethernet
Switch, loosen the screws.
Step 2: Place the wall-mount plate on the rear panel of the Industrial
Gigabit Ethernet Switch.
Step 3: Use the screws to screw the wall-mount plate on the Industrial
Gigabit Ethernet Switch.
Step 4: Use the hook holes at the corners of the wall-mount plate to
hang the Industrial Gigabit Ethernet Switch on the wall.
Step 5: To remove the wall-mount plate, reverse the steps above.
PLANET TECHNOLOGY CORPORATION
e-mail: sales@planet.com.tw http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886 2219-2- -9518 Fax:886 2219 9528-2- -
EC Declaration of Conformity
For the following equipment:
*Type of Product : Industrial 5 Port 10/100/1000T Compact Gigabit Ethernet Switch-
*Model Number : IGS-500T
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan, R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2014 30/ /EU).
For the evaluation regarding the EMC, the following standards were applied:
EN 55032 ( 5 + 6)201 AC:201
EN61000 2014-3-2 ( )
EN61000 2013-3-3 ( )
EN 55024 (2010 + A1:2015)
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan,
R.O.C.
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Director
Taiwan
June 28, 2017
Place
Date
Legal Signature
Customer Support
Thank you for purchasing PLANET products. You can browse our online
FAQ resource on PLANET web site rst to check if it could solve your
issue. If you need more support information, please contact PLANET
switch support team.
PLANET online FAQs :
http://www.planet.com.tw/en/support/faq.php
Switch support team mail address :
support_switch@planet.com.tw
Copyright © PLANET Technology Corp. 2017.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.

Specyfikacje produktu

Marka: Planet
Kategoria: przełącznik
Model: IGS-500T

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Planet IGS-500T, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje przełącznik Planet

Planet

Planet IGTP-805AT Instrukcja

5 Października 2024
Planet

Planet IPM-16230 Instrukcja

5 Października 2024
Planet

Planet FSD-804P Instrukcja

5 Października 2024
Planet

Planet UPOE-1600G Instrukcja

3 Października 2024
Planet

Planet WS-1032P Instrukcja

3 Października 2024
Planet

Planet IPOE-162S Instrukcja

3 Października 2024
Planet

Planet IPOE-162 Instrukcja

3 Października 2024
Planet

Planet XGS3-24242 Instrukcja

3 Października 2024
Planet

Planet POE-171 Instrukcja

3 Października 2024
Planet

Planet POE-171A-95 Instrukcja

3 Października 2024

Instrukcje przełącznik

Najnowsze instrukcje dla przełącznik

Netgear

Netgear GS110TPP Instrukcja

15 Października 2024
ZyXEL

ZyXEL SFP-LHX1310-40-D Instrukcja

14 Października 2024
Tripp Lite

Tripp Lite B005-DPUA4 Instrukcja

11 Października 2024
Lancom

Lancom CS-8132F Instrukcja

9 Października 2024
Lancom

Lancom YS-7154CF Instrukcja

9 Października 2024
TP-Link

TP-Link Festa FS328G Instrukcja

9 Października 2024
Totolink

Totolink SW24DM Instrukcja

9 Października 2024
Totolink

Totolink SW1008P Instrukcja

9 Października 2024
Totolink

Totolink SW24G2 Instrukcja

9 Października 2024
Cudy

Cudy FS1006P Instrukcja

9 Października 2024