Instrukcja obsługi Planet GSW-2824P

Planet przełącznik GSW-2824P

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Planet GSW-2824P (4 stron) w kategorii przełącznik. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 24-Port 10/100/1000T 802.3at PoE +
2-Port 10/100/1000T + 2-Port Gigabit TP/SFP Combo Ethernet Switch,
GSW-2824P. “802.3at PoE+ Switch” mentioned in this Guide refers to
the GSW-2824P.
Open the box of the 802.3at PoE+ Switch and carefully unpack it. The
box should contain the following items:
The 802.3at PoE+ Switch x 1 User’s Manual x 1 Power Cord x 1
SFP Dust Cap
x 2 Screws x 8 Rack-mounting
Brackets x 2 Rubber Feet x 4
If any of these pieces are missing or damaged, please contact your
dealer immediately; if possible, retain the carton including the original
packing material, and use them again to repack the product in case
there is a need to return it to us for repair.
− VLAN mode: Ports 1~24 cannot communicate with each other,
but can communicate with the uplink ports 25~28 and SFP
ports27~28
− Extend mode: Ports 1~8 have data rate of 10Mbps. The
farthest transmis-sion distance is up to 250 meters and all
ports can communicate with each other.
 VLAN mode is to isolate ports to prevent broadcast storm and
defendDHCPspoong
Automatic address learning and address aging
Hardware
19-inch rack-mount size, 1U height
LED indicators for system power, per port PoE ready and PoE
activity,speed,Link/Act
 2fanstoprovidestableandecientpowerperformance
Supports contact discharge of±6KV DC and air distance discharge
of±8KVDCforEthernetESDprotection
 Supports±6KVsurgeimmunity
3.ProductSpecications
Model GSW-2824P
HardwareSpecications
10/100/1000BASE-T
Copper Ports 28 auto MDI/MDIX
1000BASE-X SFP/
mini-GBIC Slots 2
4.2 LED Indicators
System
LED Color Function
PWR Green Lights to indicate the Switch has power.
Per 10/100/1000BASE-T Port (port 1~28)
LED Color Function
1000
LNK/ACT Green
Lights to indicate the link through that
port is successfully established.
Blinks to indicate that the Switch is
activelysendingorre-ceivingdataover
that port.
10/100
LNK/ACT Amber
Lights to indicate the link through that
port is successfully established.
Blinks to indicate that the Switch is
activelysendingorre-ceivingdataover
that port.
PoE in Use
(port1~24) Amber Lightstoindicatetheportisproviding
PoE DC in-line power.
Per 1000BASE-X SFP combo Interface (port 27~28)
LED Color Function
1000
LNK/ACT Green
Lights to indicate the link through that port
is successfully established at 1000Mbps.
BlinkstoindicatethattheSwitchisactively
sendingorreceivingdataoverthatport.
Switch
Throughput@64bytes 41.66Mpps
MAC Address Table 8K entries
Jumbo Frame 9216 bytes
Flow Control IEEE 802.3x pause frame for full duplex;
back pressure for half duplex
PoweroverEthernet
PoE Standard IEEE802.3atPoweroverEthernetPlus/PSE
PoE Injector Ports 24
PoE Power Supply
Type End-span:1/2(+),3/6(-)
PoE Power Output
Perport54±1VDC,300mA.max.15.4
watts(IEEE802.3af)
Perport54±1VDC,600mA.max.32watts
(IEEE802.3at)
PoE Power Budget 250 watts
Number of PDs,
7 watts 24
Number of PDs,
15.4 watts 16
Number of PDs,
30 watts 8
Standards Conformance
Regulatory
Compliance FCC Part 15 Class A, CE
2. Product Features
Physical Port
24-port 10/100/1000BASE-T RJ45 copper with PoE injector func-
tion
4 10/100/1000BASE-T RJ45 copper interfaces
 21000BASE-XSFPcombointerfaces,sharedwithPorts27~28
 PoweroverEthernet
 Complies with IEEE 802.3at Power over Ethernet Plus end-span
PSE
Up to 24 ports of IEEE 802.3af/802.3at devices powered (ports
1~24)
Supports PoE power up to 32 watts for each PoE port, with a total
PoE budget of 250W.
 Eachportsupports54VDCpowertoPoEpowereddevice.
 Autodetectspowereddevice(PD)
 SupportsPDalivefunction.
 Circuitprotectionpreventspowerinterferencebetweenports.
Remote power feeding up to 100m in standard mode with 250m in
extend mode
Switching
Hardware-based 10/100/1000Mbps auto-negotiation and auto MDI/
MDI-X
Supports IEEE802.3x ow control in full-duplex mode and back-
pressure in half-duplex mode
Integrates address look-up engine, supporting 8K absolute MAC
addresses
 9Kjumboframesupportsallspeeds(10/100/1000Mbps)
Hardware-based DIP switch for or mode Standard, VLAN Extend
selection;
DIP Switch
Selectable operation mode
Standard
VLAN
Extend
Dimensions
(WxDxH) 207.3x441.5x44mm(1Uheight)
Enclosure Metal
Weight 3022g
Power Requirements 100~240VAC,50/60Hz,5Amax.
Power Consumption/
Dissipation Max. 298 watts/1017 BTU
Thermal Fan 2
ESD Protection Contactdischargeof±6KVDC,
Airdischargeof±8KVDC
Surge Protection ±6KV
Installation Desktop or rack-mount installation
LED
System
Power(Green)
10/100/1000T RJ45 Interfaces
1000LNK/ACT(Green)
1000X SFP Interfaces
1000LNK/ACT(Green)
Switching
Switch Architecture Store-and-Forward
Switch Fabric 56Gbps
Standards
Compliance
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab Gigabit 1000BASE-T
IEEE 802.3z Gigabit SX/LX
IEEE802.3xowcontrolandbackpressure
IEEE802.3afPoweroverEthernet
IEEE802.3atPoweroverEthernetPlus
IEEE802.3azEnergyEcientEthernet
Environment
Operating
Temperature:0~50degreesC
(non-condensing)
Storage RelativeHumidity:5~95%
(non-condensing)
4. Hardware Introduction
4.1 Front Panel
The Front Panel of the 802.3at PoE+ Switch consists of 24-Port
10/100/1000T + 2-Port 10/100/1000T + 2-Port Gigabit TP/SFP Combo
ports. The LED Indicators are also located on the front panel of the
802.3at PoE+ Switch.
PWR
1
2
3
4
1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 18 19 20 21 22 23 2411
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 18 19 20 21 22 23 2411
26
25
28
27 27 28
Standard
VLAN
Extend
10/100
1000
LNK/ ACT
LNK/ ACT
PoE-in-Us e
1000X SFP
Figure 4-1: GSW-2824P Switch Front Panel
4.3 Multiple Functions of DIP Switch
The front panel of the 802.3at PoE+Switch provides one DIP switch for
Standard, VLAN or Extend mode selection. The detailed descriptions
are shown in the following table.
DIP Switch Mode Function
Standard
VLAN
Extend
This mode makes the 802.3at PoE+ Switch
operate as a general switch and all PoE
ports operate at 10/100/1000Mbps auto-
negotiation. All ports can communicate with
one another.
Standard
VLAN
Extend
This mode makes the 802.3at PoE+ Switch
operate as a switch andVLAN isolation
1. Ports1to24willisolaterespectively.
2. Ports 1 to 24 can only communicate with
ports25~28.
Standard
VLAN
Extend
This mode makes the 802.3at PoE+ Switch
operate as a Long Reach PoE switch and
1. Ports 1 to 8 support farthest transmission
distance of up to 250 meters
2. Ports1to8haveadatarateof10Mbps
3. All ports can communicate with one
anothe.
Note
Please adjust the DIP switch before powering on the
802.3at PoE+ Switch.
- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Standard Mode (default)
Power
100 meters (328 feet)
PoE
PoE
10BASE-T UTP with PoE
PoE IP Camera
GSW-2824P
Standard
VLAN
Extend
VLAN Isolation Mode
NVR
PC
Ports 1 to 24
Access Denied
PoE
PoE
PoE
PoE
100BASE-TX UTP with PoE
GSW-2824P
IP Camera
IP Camera
IP Camera
Ports 25~28
to Ports 1~24 Access Permitted
1000BASE-T UTP
Standard
VLAN
Extend
Extend Mode
Ports 1 to 8
Power
250 meters (820 feet)
PoE
PoE
10BASE-T UTP with PoE
PoE IP Camera
GSW-2824P
Standard
VLAN
Extend
5. Hardware Installation
5.1 Rack Mounting
To install the 802.3at PoE+ Switch in a 19-inch standard rack, follow the
instructions de-scribed below.
Step 1: Place your 802.3at PoE+ Switch on a hard at surface, with
the front panel positioned towards your front side.
Step 2: Attach a rack-mount bracket to each side of the 802.3at PoE+
Switch with sup-plied screws attached to the package. Figure
5-1 shows how to attach brackets to one side of the 802.3at
PoE+ Switch.
PWR
1
2
3
4
123456 7 89 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
1234
56789 10 1112 131 4
1516 1718 19 20 2122 2324 26
25
2
8
27 27 28
Standard
VLAN
Ext end
10/10
0
1000
LN
K/AC T
LNK/AC T
Po
E-in-Use
1000X S
FP
Figure 5-1: Attaching the Brackets to the 802.3at PoE+ Switch.
Caution
You must use the screws supplied with the mounting
brackets. Dam-age caused to the parts by using incorrect
screwswouldinvalidatethewarranty.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second bracket to the
opposite side.
4.4 Rear Panel
The rear panel of the 802.3at PoE+ Switch indicates an AC power
socket,whichacceptsinputpowerfrom100to240VAC,50-60Hz,5A.
50/60Hz
100-240V , 5A max.
Figure 4-2: GSW-2824P Switch Rear Panel
AC Power Receptacle
Power
Notice
The device is a power-required device, which means it
will not work till it is powered. If your networks should
be active all the time, please con-sider using UPS
(Uninterrupted Power Supply) for your device. It will
preventyoufromnetworkdatalossornetworkdowntime.
Power
Notice
In some areas, installing a surge suppression device may
also help to protect your 802.3at PoE+ Switch from being
damaged by unregulated surge or current to the 802.3at
PoE+ Switch or the power adapter.
Step 5: After the brackets are attached to the 802.3at PoE+ Switch,
use suitable screws to se-curely attach the brackets to the
rack, as shown in Figure 5-2.
PWR
1
2
3
4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
18
19 20
21 222
3 24
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
1 2 3 4 5 6 7 8 910 1112 1 3
14 15 16 1718 19 20 2122 232 4 26
25
28
27
27 28
Standard
VLA N
Ext end
10/100
1000
LNK/A C T
LNK/A C T
PoE-in-Use
1000X
SFP
Figure 5-2: Mounting the 802.3at PoE+ Switch in a Rack
Step 6: Connect your 802.3at PoE+ Switch to 802.3af/802.3at
compliedPDsandothernetworkdevices.
A. Connect one end of a standard network cable to the
10/100/1000BASE-T RJ45 ports on the front panel of the 802.3at
PoE+ Switch.
B. Connect theotherendof thecableto thenetwork devicessuchas
printerservers,workstationsorrouters,etc.
Step 7: Supply power to the 802.3at PoE+ Switch.
A. Connect one end of the power cable to the 802.3at PoE+ Switch.
B. Connect the power plug of the power cable to a standard wall
outlet.
When the 802.3at PoE+ Switch receives power, the power LED should
remain solid Green.
5.2 Installing the SFP Transceiver
The sections describe how to insert an SFP transceiver into an SFP slot
of the 802.3at PoE+ Switch.
TheSFPtransceiversarehot-pluggableandhot-swappable.Youcanplug
inandoutthetransceiverto/fromanySFPportwithouthaving topower
down the 802.3at PoE+ Switch, as the Figure 5-3 shows.
PWR
1
2
3
4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
1 2 34567 8 9 10 11 12 13 14 1516 17 18 19 20 21
22 2324 26
25
28
27 28
Standard
VLAN
Extend
10/100
1000
LNK/ACT
LNK/ACT
PoE-in
-Use
1000
X SFP
MGB-Series SFP Transceiver
LC Fiber Cable
1
2
Figure 5-3: Plugging In the SFP Transceiver
Approved PLANET SFP Transceivers
PLANET 802.3at PoE+ Switch supports both single mode and multi-
mode SFP trans-ceivers. The website link of approved PLANET SFP
transceiversisshownbelow:
https://www.planet.com.tw/en/product/mgb-series-transceiver
Note
It is recommended to use PLANET SFP on the 802.3at
PoE+Switch. If you insert an SFP transceiverthat is not
supported, the 802.3at PoE+ Switch will not recognize it.
1. Before we connect the 802.3at PoE+ Switch to the other network
device, we haveto make sure both sides of the SFP transceiversare
with the same media type, for example, 1000BASE-SX to 1000BASE-
SX; 1000BASE-LX to 1000BASE-LX.
2.Check whethertheber-optic cabletypematches withthe SFPtrans-
ceiverrequirement.
To connect to 1000BASE-SX SFP transceiver, please use the
multi-mode ber cable with one side being the male duplex LC
connector type.
To connect to 1000BASE-LX SFP transceiver, please use the
single-mode ber cable with one side being the male duplex LC
connector type.
Customer Support
Thank you for purchasing PLANET products. You can browse our online
FAQ resource on PLANET Web site rst to check if it could solve your
issue. If you need more support information, please contact PLANET
support team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq
Support team mail address
support@planet.com.tw
Copyright © PLANET Technology Corp. 2021
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.

Specyfikacje produktu

Marka: Planet
Kategoria: przełącznik
Model: GSW-2824P

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Planet GSW-2824P, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje przełącznik Planet

Planet

Planet IGTP-805AT Instrukcja

5 Października 2024
Planet

Planet IPM-16230 Instrukcja

5 Października 2024
Planet

Planet FSD-804P Instrukcja

5 Października 2024
Planet

Planet UPOE-1600G Instrukcja

3 Października 2024
Planet

Planet WS-1032P Instrukcja

3 Października 2024
Planet

Planet IPOE-162S Instrukcja

3 Października 2024
Planet

Planet IPOE-162 Instrukcja

3 Października 2024
Planet

Planet XGS3-24242 Instrukcja

3 Października 2024
Planet

Planet POE-171 Instrukcja

3 Października 2024
Planet

Planet POE-171A-95 Instrukcja

3 Października 2024

Instrukcje przełącznik

Najnowsze instrukcje dla przełącznik

Intermatic

Intermatic P1101 Instrukcja

20 Marca 2025
AirLive

AirLive IG-641RPOE Instrukcja

12 Marca 2025
AirLive

AirLive IGM-1082RBT Instrukcja

12 Marca 2025
APC

APC AP7532 Instrukcja

10 Marca 2025
Lancom

Lancom GS-3628XP Instrukcja

10 Marca 2025
Advantech

Advantech EKI-9510E-2GMPW-B Instrukcja

10 Marca 2025
Theben

Theben ELPA 9 Instrukcja

5 Marca 2025
Digitus

Digitus DN-80113-2 Instrukcja

27 Lutego 2025
Leviton

Leviton 47611-C6B Instrukcja

25 Lutego 2025
Yamaha

Yamaha SWX2322P-16MT Instrukcja

22 Lutego 2025