Instrukcja obsługi Pioneer SPH-DA250DAB

Pioneer Radia samochodowe SPH-DA250DAB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pioneer SPH-DA250DAB (47 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/47
English Français Italiano Español Deutsch Nederlands
SPH-DA250DAB
RDS AV RECEIVER
AUTORADIO MULTIMÉDIA RDS
SINTOLETTORE AV CON RDS
AV RECEPTOR RDS
RDS-AV-RECEIVER
RDS AV-ONTVANGER
Installation Manual
Manuel d'installation
Manuale d'installazione
Manual de instalación
Installationsanleitung
Installatiehandleiding
2En
•Do not operate this product, any
applications, or the rear view camera
option (if purchased) if doing so will
divert your attention in any way from the
safe operation of your vehicle. Always
observe safe driving rules and follow all
existing traffic regulations. If you
experience difficulty in operating this
product, pull over, park your vehicle in a
safe location and apply the handbrake
before making the necessary
adjustments.
•Do not install this product where it may
(i) obstruct the driver’s vision,
(ii) impair the performance of any of the
vehicle’s operating systems of safety
features, including airbags, hazard lamp
buttons, or
(iii) impair the driver’s ability to safely
operate the vehicle.
In some cases, it may not be possible to
install this product because of the vehicle
type or the shape of the vehicle interior.
WARNING
Pioneer does not recommend that you
install this product yourself. This product is
designed for professional installation only.
We recommend that only authorised
Pioneer service personnel, who have
special training and experience in mobile
electronics, set up and install this product.
NEVER SERVICE THIS PRODUCT YOURSELF.
Installing or servicing this product and its
connecting cables may expose you to the
risk of electric shock or other hazards, and
can cause damage to this product that is
not covered by warranty.
WARNING
Do not take any steps to tamper with or
disable the handbrake interlock system
which is in place for your protection.
Tampering with or disabling the
handbrake interlock system could result in
serious injury or death.
CAUTION
•Secure all wiring with cable clamps or
electrical tape. Do not allow any bare
wiring to remain exposed.
•Do not directly connect the yellow lead of
this product to the vehicle battery. If the
lead is directly connected to the battery,
engine vibration may eventually cause
the insulation to fail at the point where
the wire passes from the passenger
compartment into the engine
compartment. If the yellow lead’s
insulation tears as a result of contact with
metal parts, short-circuiting can occur,
resulting in considerable danger.
•It is extremely dangerous to allow cables
to become wound around the steering
column or gearstick. Be sure to install this
product, its cables, and wiring away in
such so that they will not obstruct or
hinder driving.
Connection
Precautions
Your new product and this
manual
Important safeguards
Precautions before
connecting the system
•Make sure that the cables and wires will
not interfere with or become caught in
any of the vehicle’s moving parts,
especially the steering wheel, gearstick,
handbrake, sliding seat tracks, doors, or
any of the vehicle’s controls.
•Do not route wires where they will be
exposed to high temperatures. If the
insulation heats up, wires may become
damaged, resulting in a short circuit or
malfunction and permanent damage to
the product.
•Do not shorten any leads. If you do, the
protection circuit (fuse holder, fuse
resistor or filter, etc.) may fail to work
properly.
•Never feed power to other electronic
products by cutting the insulation of the
power supply lead of this product and
tapping into the lead. The current
capacity of the lead will be exceeded,
causing overheating.
•Use this product with a 12-volt battery
and negative earthing only. Failure to do
so may result in a fire or malfunction.
•To avoid shorts in the electrical system,
be sure to disconnect the (–) battery
cable before installation.
WARNING
•When speaker output is used by 4
channels , use speakers over 50 W
(Maximum input power) and between 4
Ω to 8 Ω (impedance value). Do not use 1
Ω to 3 Ω speakers for this unit.
•When rear speaker output is used by 2 Ω
of subwoofer, use speakers over 70 W
(Maximum input power).
*Please refer to connection for a
connection method.
•The black lead is earth. Please earth this
lead separately from the earth of high
current products such as power amps. Do
not earth more than one product
together with the earth from another
product. For example, you must
separately earth any amp unit away from
the earth of this product. Connecting
earths together can cause a fire and/or
damage the products if their earths
became detached.
•When replacing the fuse, be sure to only
use a fuse of the rating prescribed on this
product.
•This product cannot be installed in a
vehicle without ACC (accessory) position
on the ignition switch.
•To avoid short-circuiting, cover the
disconnected lead with insulating tape. It
is especially important to insulate all
unused speaker leads, which if left
uncovered may cause a short circuit.
•For connecting a power amp or other
devices to this product, refer to the
manual for the product to be connected.
•The graphical symbol placed on
the product means direct current.
•When the ignition switch is turned on
(ACC ON), a control signal is output
through the blue/white lead. Connect to
an external power amp’s system remote
Before installing this
product
To prevent damage
Notice for the blue/
white lead
ACC position No ACC position
3En
English
control terminal, the auto-aerial relay
control terminal, or the aerial booster
power control terminal (max. 300 mA 12
V DC). The control signal is output
through the blue/white lead, even if the
audio source is switched off.
Microphone 3 m
Wired remote input
Hard-wired remote control adapter can
be connected (sold separately).
This product
Digital Radio aerial input
Aerial jack
Subwoofer output (STD)/Low range
output (NW)
Rear output (STD)/Middle range output
(NW)
Front output (STD)/High range output
(NW)
Power supply
Fuse (10 A)
To power supply
Depending on the kind of vehicle, the
function of 2* and 4* may be different.
In this case, be sure to connect 1* to 4*
and 3* to 2*.
Yellow (2*)
Back-up (or accessory)
Yellow (1*)
Connect to the constant 12 V supply
terminal.
Red (4*)
Accessory (or back-up)
This product
Power cord Red (3*)
Connect to terminal controlled by
ignition switch (12 V DC).
Connect leads of the same colour to
each other.
Orange/white
To lighting switch terminal.
Black (earth)
To vehicle (metal) body.
Blue/white (5*)
The pin position of the ISO connector
will differ depending on the type of
vehicle. Connect 5* and 6* when Pin 5 is
an aerial control type. In another type of
vehicle, never connect 5* and 6*.
Blue/white (6*)
Connect to auto-aerial relay control
terminal (max. 300 mA 12 V DC).
Blue/white
Connect to system control terminal of
the power amp (max. 300 mA 12 V DC).
Violet/white
Of the two lead wires connected to the
back lamp, connect the one in which
the voltage changes when the gear shift
is in the REVERSE (R) position. This
connection enables the unit to sense
whether the car is moving forwards or
backwards.
Light green
Used to detect the ON/OFF status of the
handbrake. This lead must be
connected to the power supply side of
the handbrake switch.
Connection method
Clamp the lead (1) then clamp firmly
with needle-nosed pliers (2).
Power supply side
Handbrake switch
Earth side
Speaker leads
White: Front left + or high range left +
White/black: Front left – or high range
left –
Grey: Front right + or high range right +
Grey/black: Front right – or high range
right –
Green: Rear left + or middle range left +
Green/black: Rear left – or middle range
left –
Violet: Rear right + or middle range
right +
Violet/black: Rear right – or middle
range right –
ISO connector
In some vehicles, the ISO connector
may be divided into two. In this case, be
sure to connect to both connectors.
NOTES
•The position of the handbrake switch
depends on the vehicle model. For
details, consult the vehicle Owner’s
Manual or dealer.
•When a subwoofer is connected to this
product instead of a rear speaker, change
the rear output setting in the initial
setting. The subwoofer output of this
product is monaural.
•When using a subwoofer of 2 Ω, be sure
to connect the subwoofer to the violet
and violet/black leads of this unit. Do not
connect anything to the green and
green/black leads.
Important
The speaker leads are not used when this
connection is in use.
Power amp (sold
separately)
Without internal amp

Specyfikacje produktu

Marka: Pioneer
Kategoria: Radia samochodowe
Model: SPH-DA250DAB

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Pioneer SPH-DA250DAB, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Radia samochodowe Pioneer

Pioneer

Pioneer SPH-PF97BT Instrukcja

5 Stycznia 2025
Pioneer

Pioneer MVH-S23BT Instrukcja

3 Stycznia 2025
Pioneer

Pioneer AVH-A240DAB Instrukcja

7 Grudnia 2024
Pioneer

Pioneer DEH-X6900BT Instrukcja

9 Października 2024
Pioneer

Pioneer AVH-120BT Instrukcja

9 Października 2024
Pioneer

Pioneer DEH-S1000UB Instrukcja

9 Października 2024
Pioneer

Pioneer DEH-S4100BT Instrukcja

9 Października 2024
Pioneer

Pioneer AVH-1330NEX Instrukcja

9 Października 2024
Pioneer

Pioneer AVH-1300NEX Instrukcja

9 Października 2024
Pioneer

Pioneer DMH-160BT II Instrukcja

9 Października 2024

Instrukcje Radia samochodowe

Najnowsze instrukcje dla Radia samochodowe

Grundig

Grundig scc 1300 vd Instrukcja

15 Stycznia 2025
Autovision

Autovision AV-9740 Instrukcja

14 Stycznia 2025
Dual

Dual XDMA6355 Instrukcja

14 Stycznia 2025
Hyundai

Hyundai H-CDM8028 Instrukcja

14 Stycznia 2025
BLOW

BLOW AVH-9810 Instrukcja

13 Stycznia 2025
Roadstar

Roadstar CD-910RDVD Instrukcja

13 Stycznia 2025
Hyundai

Hyundai H-CCR8085 Instrukcja

13 Stycznia 2025
Caliber

Caliber MCD786 Instrukcja

13 Stycznia 2025
Autovision

Autovision AV-9200TBT Instrukcja

13 Stycznia 2025
Alpine

Alpine TDM-9501RM Instrukcja

12 Stycznia 2025