Instrukcja obsługi Pioneer S-RS55TB

Pioneer głośnik S-RS55TB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pioneer S-RS55TB (12 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/12

Thank you for buying this Pioneer product.

Please read through these operating instructions before using your

speaker system to optimize performance.

WHAT'S IN THE BOX

1. Front speakers (2)

2. Surround speakers (2)

3. Center speaker (1)

4. Speaker cables

Center speaker (1) (2 m, Tie color: Red)

Front speakers (2) (3 m, Tie color: Black)

Surround speakers (2) (10 m, Tie color: Blue)

5. Non-skid pads (1) (20 pcs)

• Operating Instructions (This manual)

BEFORE USE

• These speakers have a rated impedance of 8 Ω. Use an

amplifier that supports speakers with an impedance of 8 Ω.

• In order to prevent damage to the speaker system resulting

from input overload, please observe the following precautions:

– Do not input above the permissible input.

– When connecting this unit and other AV devices to an

amplifier, turn the amplifier off first.

– When amplifying the treble with a graphic equalizer, do not

increase the volume too much.

– Do not output loud volumes through a low output amplifier.

(The harmonic distortion of the amplifier will increase, and

there is a possibility of damage to the speakers.)

• Do not use the speaker to output distorted sound for long

periods of time. This can result in a fire hazard.

• Do not install these units near a stove or other heating

appliance, or put them in a place exposed to the sun. Such

locations may cause the cabinet to change color and the

speaker system to break down.

• Do not attach the front and center speakers to the wall or

ceiling. It may fall off and cause injury.

• These speakers are not equipped with magnetic shielding.

Do not put items easily affected by magnetism (cards with

magnetic tape, etc.) near this unit.

• Some color irregularity or distortion may occur on a cathode

ray tube television (CRT television) if you use one near this

unit. Separate these speakers further from the television if this

occurs.

PLACEMENT AND FINE TUNING

STANDARD SURROUND SETUP

This is a standard multichannel surround sound speaker setup for

optimal 5.1 channel home theater sound.

1, 2. Front Speakers

3. Center Speaker

4, 5. Surround Speakers

6. Subwoofer

Front Speakers

For best results the speakers should be separated a distance

approximately equal to the listening distance. Angling the speakers

inward towards the listener will improve the image stability for

non-central listeners. Close proximity to a side or rear wall will

enhance the midbass performance, although too close (particularly

a corner location) and the bass may be unnaturally high and image

performance may be degraded.

Center Speaker

The speaker should be positioned below the TV. For best results

align the front of the speaker with the front of the TV. If the speaker

is placed under the TV and very close to the floor, then tilting

upwards may be beneficial.

Do not place the center speaker on top of TV, the speaker may

fall from the TV due to external shocks such as earthquakes,

endangering those nearby or damaging the speaker.

Operating Instructions

Speaker System

S-RS55TB

Surround Speakers

For best results the speakers should be positioned at or above ear

level. Depending upon your room layout and preferences, the left

and right rear speakers should be positioned on the side walls just

the rear of the listening position, or on the walls.

NON-SKID PADS

Use the supplied non-skip pads as necessary according to the

location chosen for installation. Stick the non-skid pads on the four

corners of the surface of the speaker on which it will be installed.

There will be locations, however, where there will be little benefit

from using the non-skid pads, so avoid putting in slippery places.

Put the units on a soft cloth when performing this task.

12 3

1. Front Speakers

2. Surround Speakers

3. Center Speaker

MAKING AMPLIFIER SETTINGS

Before connecting the speakers, please read the operating

instructions supplied with your amplifier to select the speaker

setting of amplifier:

• Front speakers: Large

• Center / surround speakers: Small

CONNECTING YOUR SYSTEM

• Make sure all equipment is turned off before making any

connections.

• You will not get the proper surround effects from the speakers if

you connect the poles (+ and –) incorrectly.

• These speaker terminals carry HAZARDOUS LIVE voltage.

To prevent the risk of electric shock when connecting or

disconnecting the speaker cables, disconnect the power cord

before touching any uninsulated parts.

Connect to the speaker terminals on the rear of the speakers

Connect the speaker cables to the speaker terminals on the rear of

the speakers. The poles of the input terminals are red for positive

(+) and black for negative (–). Match the colors of the speaker

terminals and speaker cables when connecting.

Front speakers:

After loosening the speaker terminals, push the wires into the

terminals, then tighten firmly.

Red 

Black 

Center and surround speakers:

While pushing the tabs of the speaker terminals, push the wires

into the terminals.

Red 

Black 

Connect to the speaker terminals on the rear of the amplifier

Connect the speaker cables to the speaker output terminals on the

rear of the amplifier. (For details, refer to the amplifier's instruction

manual.)

Speakers

Amplifier

• After connecting the cord to the terminal, pull the cord gently

to make sure the end of the cord is firmly connected to the

terminal. Incomplete connection may result in the sound

jumping or noise being output.

• To prevent damage to the circuits, ensure that the + and – wires

of the speaker cables and the left and right wires do not touch

each other. Also take care that the bare wires do not touch the

rear panel of the amplifier.

WALL-MOUNTING THE SURROUND

SPEAKERS

Mounting screw

(not supplied)

5 mm to 7 mm

3.7 mm

9.3 mm

• The mounting screws are not supplied. Use screws that suit the

wall material and that can sufficiently support the weight of the

speakers.

• When you intend to attach to the wall, first ensure that the

wall is strong enough to sufficiently support the weight of the

speakers.

• After attaching, check that the fitting is secure. Continue to

check that the fitting is secure at regular intervals thereafter.

• If you are unsure of the quality and strength of the walls,

consult a professional for advice.

• We are not responsible for any accidents or damage that result

from improper installation.

SECURING THE FRONT SPEAKERS

Pass a commercially-available reinforced string through the plastic

catch to securely support the speaker to the wall. Also ensure

that the wall you are fixing the speaker to is strong enough to

sufficiently support the weight of the speaker.

Reinforced strings

(not supplied)

Plastic catches

Backside of front speaker

• Do not attach the plastic catches directly to the wall.

• After attaching, check that the fitting is secure. Continue to

check that the fitting is secure at regular intervals thereafter.

• If you are unsure of the quality and strength of the walls,

consult a professional for advice.

• We are not responsible for any accidents or damage that result

from improper installation.

CABINET MAINTENANCE

Use a polishing cloth or dry cloth to wipe off dust and dirt.

When the cabinet is very dirty, clean with a soft cloth dipped in

some neutral cleanser diluted five or six times with water, and

then wipe again with a dry cloth. Do not use furniture wax or

cleaners. Never use thinners, benzine, insecticide sprays and other

chemicals on or near the cabinets, since these will corrode the

surfaces.

TROUBLESHOOTING

Symptom Possible cause Remedy

No sound. • Bad speaker cable

or connection.

• Amplifier is off.

• Volume control is at

zero.

• Connect correctly or

replace cable.

• Turn on amplifier.

• Slowly turn up volume.

Sound is

distorted.

• Extreme signal

condition.

• Turn down the

amplifier's output level

(volume, bass control,

bass boost) to lower the

level.

Names of the parts

Front speakers

1. Cabinet

2. Woofer

3. Tweeter

4. Plastic catches

5. Speaker terminals

6. Bass ref duct

Surround speakers

1. Cabinet

2. Speaker

3. Bass ref duct

4. Wall attachment fitting

5. Speaker terminals

Center speaker

1. Cabinet

2. Speaker

3. Bass ref duct

4. Speaker terminals

Specyfikacje produktu

Marka:	Pioneer
Kategoria:	głośnik
Model:	S-RS55TB

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Pioneer S-RS55TB, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje głośnik Pioneer

Pioneer RM-07 Instrukcja

30 Grudnia 2025

Pioneer TS-A1607C Instrukcja

14 Grudnia 2024

Pioneer TS-G1320S Instrukcja

14 Grudnia 2024

Pioneer TS-A4103 Instrukcja

14 Grudnia 2024

Pioneer TS-A879 Instrukcja

14 Grudnia 2024

Pioneer TS-G1020S Instrukcja

14 Grudnia 2024

Pioneer TS-G4620S Instrukcja

14 Grudnia 2024

Pioneer TS-G6820S Instrukcja

14 Grudnia 2024

Pioneer TS-G1620F Instrukcja

14 Grudnia 2024

Pioneer TS-A878 Instrukcja

14 Grudnia 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Bowers & Wilkins LCR3 Instrukcja

15 Stycznia 2025

Hifonics Vulcan VX6.2E Instrukcja

15 Stycznia 2025

Pyle PLRGSW64BK Instrukcja

15 Stycznia 2025

ION Insta Sound Instrukcja

15 Stycznia 2025

Pure Acoustics QBT-340 Instrukcja

15 Stycznia 2025

Yamaha WX-010 Instrukcja

15 Stycznia 2025

Polk REACT SOUND BAR 1 Instrukcja

15 Stycznia 2025

Sennheiser AMBEO Soundbar Plus SB02M Instrukcja

15 Stycznia 2025

Klipsch Reference RB-25 Instrukcja

15 Stycznia 2025

Klipsch Reference RB-35 Instrukcja

15 Stycznia 2025