Instrukcja obsługi Pioneer DEH-X8700BT

Pioneer Radia samochodowe DEH-X8700BT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pioneer DEH-X8700BT (32 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/32
English Français Italiano Español Deutsch Nederlands Русский
CD RDS RECEIVER
AUTORADIO CD RDS
SINTOLETTORE CD RDS
REPRODUCTOR DE CD CON RECEPTOR RDS
CD RDS-EMPFÄNGER
CD RDS-ONTVANGER
CD RDS ПРИЕМНИК
DEH-X8700DAB
DEH-X8700BT Installation Manual
Manuel d’installation
Manuale d’installazione
Manual de instalación
Installationsanleitung
Installatiehandleiding
Руководство по установке
2En
Important
•When installing this unit in a vehicle
without an ACC (accessory) position on
the ignition switch, failure to connect the
red cable to the terminal that detects
operation of the ignition key may result
in battery drain.
•Use of this unit in conditions other than
the following could result in fire or
malfunction.
–Vehicles with a 12-volt battery and
negative grounding.
–Speakers with 50 W (output value) and
4 Ω to 8 Ω (impedance value).
•To prevent a short-circuit, overheating or
malfunction, be sure to follow the
directions below.
–Disconnect the negative terminal of the
bat tery before installation.
–Secure the wiring with cable clamps or
adhesive tape. Wrap adhesive tape
around wiring that comes into contact
with metal parts to protect the wiring.
– Place all cables away from moving parts,
su ch as the shift lever and seat rails.
–Place all cables away from hot places,
such as near the heater outlet.
–Do not connect the yellow cable to the
battery by passing it through the hole
to the engine compartment.
–Cover any disconnected cable
connectors with insulating tape.
–Do not shorten any cables.
–Never cut the insulation of the power
cable of this unit in order to share the
power with other devices. The current
capacity of the cable is limited.
–Use a fuse of the rating prescribed.
–Never wire the negative speaker cable
directly to ground.
–Never band together negative cables of
multiple speakers.
•When this unit is on, control signals are
sent through the blue/white cable.
Connect this cable to the system remote
control of an external power amp or the
vehicle’s auto-antenna relay control
terminal (max. 300mA 12 V DC). If the
vehicle is equipped with a glass antenna,
connect it to the antenna booster power
supply terminal.
•Never connect the blue/white cable to
the power terminal of an external power
amp. Also, never connect it to the power
terminal of the auto antenna. Doing so
may result in battery drain or a
malfunction.
•The black cable is ground. Ground cables
for this unit and other equipment
(especially, high-current products such as
power amps) must be wired separately. If
they are not, an accidental detachment
may result in a fire or malfunction.
Connections/Installation
Connections
ACC position No ACC position
This unit
Antenna input
Microphone 4 m
Microphone input
DAB antenna input (Only for DEH-
X8700DAB)
Power cord input
AUX input jack (3.5 mm stereo jack)
Rear output
Front output
Subwoofer output
Wired remote input
Hard-wired remote control adapter can
be connected (sold separately).
Fuse (10 A)
USB port
USB cable 1.5 m
Power cord
To power cord input
Depending on the kind of vehicle, the
function of and may be different.
In this case, be sure to connect to
and to .
Yel low
Back-up (or accessory)
Yel low
Connect to the constant 12 V supply
terminal.
Red
Accessory (or back-up)
Red
Connect to terminal controlled by the
ignition switch (12 V DC).
Connect leads of the same color to each
other.
Black (chassis ground)
Blue/white
The pin position of the ISO connector
will differ depending on the type of
vehicle. Connect and when Pin 5
is an antenna control type. In another
type of vehicle, never connect and
.
3En
English
Blue/white
Connect to the system control terminal
of the power amp (max. 300 mA 12 V
DC).
Blue/white
Connect to the auto-antenna relay
control terminal (max. 300 mA 12 V DC).
Speaker leads
White: Front left
White/black: Front left
Gray: Front right
Gray/black: Front right
Green: Rear left or subwoofer
Green/black: Rear left or subwoofer
Violet: Rear right or subwoofer
Violet/black: Rear right or subwoofer
Orange/white
Connect to a car’s illumination signal.
ISO connector
In some vehicles, the ISO connector
may be divided into two. In this case, be
sure to connect to both connectors.
NOTES
•Change the initial menu of this unit. Refer
to [S/W control]. The subwoofer output of
this unit is monaural.
•W
hen using a subwoofer of 70 W (2 Ω), be
sure to connect the subwoofer to the
violet and violet/black leads of this unit.
Do not connect anything to the green
and green/black leads.
Power amp (sold separately)
Perform these connections when using the
optional amplifier.
System remote control
Connect to blue/white cable.
Power amp (sold separately)
Connect with RCA cables (sold
separately)
To rear output
Rear speaker
To front output
Front speaker
To subwoofer output
Subwoofer
Important
•Check all connections and systems before
final installation.
•Do not use unauthorized parts as this
may cause malfunctions.
•Consult your dealer if installation requires
drilling of holes or other modifications to
the vehicle.
•Do
not install this unit where:
– it may interfere with operation of the
vehicle.
– it may cause injury to a passenger as a
result of a sudden stop.
Installation
•The semiconductor laser will be damaged
if it overheats. Install this unit away from
hot places such as near the heater outlet.
•Optimum performance is
obtained when the unit is
installed at an angle of less
than 60°.
•When installing, to ensure proper heat
dispersal when using this unit, make sure
you leave ample space behind the rear
panel and wrap any loose cables so they
are not blocking the vents.
DIN front/rear mount
This unit can be properly installed using
either front-mount or rear-mount
installation.
Use commercially available parts when
installing.
DIN Front-mount
1Insert the mounting sleeve into the
dashboard.
For installation in shallow spaces, use
the supplied mounting sleeve. If there is
enough space, use the mounting sleeve
that came with the vehicle.
2Secure the mounting sleeve by using a
screwdriver to bend the metal tabs
(90°) into place.
Dashboard
Mounting sleeve
•Make sure that the unit is installed
securely in place. An unstable
installation may cause skipping or
other malfunctions.
DIN Rear-mount
1Determine the appropriate position
where the holes on the bracket and
the side of the unit match.
2Tighten two screws on each side.
Tapping screw (5 mm × 8 mm)
Mounting bracket
Dashboard or console
Removing the unit
1Remove the trim ring.
Trim ring
Notched tab
•Releasing the front panel allows easier
access to the trim ring.
•When reattaching the trim ring, point
the side with the notched tab down.
2Insert the supplied extraction keys
into both sides of the unit until they
click into place.
3Pull the unit out of the dashboard.
Leave ample
space 5 cm
5 cm

Specyfikacje produktu

Marka: Pioneer
Kategoria: Radia samochodowe
Model: DEH-X8700BT

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Pioneer DEH-X8700BT, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Radia samochodowe Pioneer

Pioneer

Pioneer SPH-PF97BT Instrukcja

5 Stycznia 2025
Pioneer

Pioneer MVH-S23BT Instrukcja

3 Stycznia 2025
Pioneer

Pioneer AVH-A240DAB Instrukcja

7 Grudnia 2024
Pioneer

Pioneer DEH-X6900BT Instrukcja

9 Października 2024
Pioneer

Pioneer AVH-120BT Instrukcja

9 Października 2024
Pioneer

Pioneer DEH-S1000UB Instrukcja

9 Października 2024
Pioneer

Pioneer DEH-S4100BT Instrukcja

9 Października 2024
Pioneer

Pioneer AVH-1330NEX Instrukcja

9 Października 2024
Pioneer

Pioneer AVH-1300NEX Instrukcja

9 Października 2024
Pioneer

Pioneer DMH-160BT II Instrukcja

9 Października 2024

Instrukcje Radia samochodowe

Najnowsze instrukcje dla Radia samochodowe

Grundig

Grundig scc 1300 vd Instrukcja

15 Stycznia 2025
Autovision

Autovision AV-9740 Instrukcja

14 Stycznia 2025
Dual

Dual XDMA6355 Instrukcja

14 Stycznia 2025
Hyundai

Hyundai H-CDM8028 Instrukcja

14 Stycznia 2025
BLOW

BLOW AVH-9810 Instrukcja

13 Stycznia 2025
Roadstar

Roadstar CD-910RDVD Instrukcja

13 Stycznia 2025
Hyundai

Hyundai H-CCR8085 Instrukcja

13 Stycznia 2025
Caliber

Caliber MCD786 Instrukcja

13 Stycznia 2025
Autovision

Autovision AV-9200TBT Instrukcja

13 Stycznia 2025
Alpine

Alpine TDM-9501RM Instrukcja

12 Stycznia 2025