Instrukcja obsługi Philips Comfort Plus GC1575

Philips Żelazo Comfort Plus GC1575

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Philips Comfort Plus GC1575 (9 stron) w kategorii Żelazo. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/9

GC1580, GC1575, GC1565

ENGLISH

General description (fig. 1)IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

ATemperature control dial

BSteam control dial

O= no steam

q= moderate steam

w= maximum steam

x= Calc-Clean function

CSpray button T

DSpray nozzle

ETemperature pilot light

FWater filling opening

GWater tank

HType plate

ICord

JExtra Steam function (press steam control dial) (type GC1580)

KAuto shut-off (type GC1580)

LRelease button for water tank

MShot of Steam function (type GC1575)

ImportantIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

For optimal safety, read these instructions carefully and look at the illustrations before

you start using the appliance.

Keep these instructions for future reference.

◗Never leave the iron unattended when it is connected to the mains.

◗This appliance is not intended for use by children.

◗Keep an eye on children to make sure that they do not play with the appliance.

◗The soleplate of the iron can become extremely hot and may cause burns if

touched.

◗Never use the appliance if it is damaged in any way.

◗When you have finished ironing, when you clean the appliance, when you fill or

empty the water tank and also when you leave the iron even for a short while:

set the steam control to position O, put the iron on its heel and remove the

mains plug from the wall socket.

◗If the supply cord is damaged, it must be replaced by a special Philips or its

service agent or a similarly qualified person in order to avoid a hazard.

◗Check if the voltage indicated on the type plate corresponds to the local mains

voltage before you connect the appliance.

Before first useIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

1Remove sticker or protective foil from the soleplate if there is any.

2Heat up the iron to the maximum temperature and pass the iron over a piece

of damp cloth for several minutes to remove any residues from the soleplate.

The iron may give off some smoke when you use it for the first time. This will cease

after a short while.

Filling the water tankIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Never immerse the iron in water.

1Remove the mains plug from the wall socket.

2Set the steam control to position O (= no steam) (fig. 2).

3Press and hold the release button and remove the detachable water tank

(fig. 3).

4Fill the water tank with cold tap water up to the maximum level (fig. 4).

Do not fill the water tank beyond the MAX indication.

Only use water. Do not use vinegar, starch, ironing concentrates or chemically

descaled water.

If the tap water in your area is very hard, we advise you to mix it with an equal

amount of distilled water or to use distilled water only.

5Push the water tank back into the iron until you hear a ‘click’.

Setting the temperatureIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

1Put the iron on its heel.

2Check the garment label for the required ironing temperature:

1Synthetic fabrics (e.g. acrylic, viscose, polyamide, polyester)

1Silk

2Wool

3Cotton, linen

If you do not know what kind of fabric(s) a garment is made of, determine the right

ironing temperature by ironing a part that will be invisible when you wear the

garment.

Silk, woollen and synthetic materials: iron the reverse side of the fabric to prevent

shiny patches. Avoid using the spray function to prevent stains.

Start ironing the articles that require the lowest ironing temperature, such as those

made of synthetic fibres.

3Set the temperature control dial to the required ironing temperature by

turning it to the appropriate temperature indication (fig. 5).

4Put the mains plug in an earthed wall socket.

5When the temperature pilot light has gone out, wait a while before you start

ironing (fig. 6).

The pilot light will go on from time to time during ironing.

Steam ironingIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

1Make sure that there is enough water in the water tank.

2After the temperature pilot light has gone out, set the steam control to the

appropriate steam position (fig. 7).

qfor moderate steam (temperature settings 2to MAX)

wfor maximum steam (temperature settings 3to MAX)

The iron will start producing steam as soon as the set temperature has been

reached.

3Set the temperature control dial to the recommended position.

See 'Setting the temperature'.

Ironing without steamIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

1Set the steam control dial to position O (= no steam).

2Set the temperature control dial to the recommended position.

See 'Setting the temperature'.

Other featuresIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Spray function

To remove stubborn creases at any temperature

◗Make sure there is enough water in the water tank.

1Press the spray button several times to moisten the article to be ironed

(fig. 8).

Extra Steam (type GC1580)

This function provides extra steam to remove very stubborn creases.

◗The Extra Steam function only works at temperature settings between 3

and MAX.

1Set the steam control dial to the maximum position w(fig. 9).

2Press and hold the steam control dial for maximal 5 seconds (fig. 10).

3Release the steam control dial and wait at least 1 minute before using this

function again to prevent water from dripping out of the soleplate.

Shot of steam (type GC1575)

A powerful shot of steam helps to remove stubborn creases.

Use the Shot-of-Steam function only at temperature settings between 3and

MAX.

1Press and release the Shot of steam button (fig. 11).

Wait for while before using the button again to avoid spluttering.

Never direct the steam towards people.

ASO - Auto shut off (type GC1580)

An electronic safety device will automatically switch off the iron if it has not been

removed for a while.

To indicate that the iron has been switched-off, the red auto-off pilot light will start

blinking (fig. 12).

- In a horizontal position, this will happen after 30 seconds.

- In a vertical position, this will happen after 8 minutes.

To heat up the iron again:

- Pick up the iron or move it slightly.

- The red auto-off pilot light will go out. The amber temperature pilot light will go

on.

- When the amber pilot light has gone out and goes on again, the iron is ready for

use.

Cleaning and maintenanceIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Calc-Clean function

The Calc-Clean function removes scale and impurities.

4239.000.5257.3

2/9

Use the Calc-Clean function once every two weeks. If the water in your area is very

hard (i.e. when flakes come out of the soleplate during ironing), you should use the

Calc-Clean function more frequently.

1Set the steam control dial to position O.

2Set the temperature control dial to MAX.

3Fill the water tank to the maximum level.

Do not pour vinegar or other descaling agents into the water tank.

4Put the plug in the wall socket.

5Unplug the iron when the temperature pilot light has gone out.

6Hold the iron over the sink and set the steam control to the Calc-Clean

position •(fig. 13).

7Pull the steam control dial slightly upwards and gently shake the iron until all

water in the tank has been used up.

Steam and boiling water will come out of the soleplate, flushing out impurities and

scale.

8Press the steam control dial back to its original position and set it to position

O after having used the Calc-Clean function.

9Repeat the Calc-Clean process if the iron still contains a lot of impurities.

10 To clean the steam control needle, pull the steam control out of the

appliance (fig. 14). Use vinegar to remove scale, if any, from the needle (fig.

15).

Do not bend or damage the steam control needle.

11Reinsert the steam control needle by placing the point of the needle exactly

in the centre of the hole and by fitting the small projection on the side of the

needle into the slot (fig. 16).

12Set the steam control to position O.

After the Calc-Clean process

1Connect the iron to the mains to let the soleplate dry.

2Unplug the iron when the pilot light has gone out.

3Move the iron gently over a piece of used cloth to remove any water stains

that may have formed on the soleplate.

4Let the iron cool down before you store it.

Cleaning after ironing

1Make sure the plug has been removed from the wall socket and the iron has

cooled down.

2Wipe scale and any other deposits off the soleplate with a damp cloth and a

non-abrasive (liquid) cleaner.

Keep the soleplate smooth: avoid contact with metal objects.

3Clean the upper part of the appliance with a damp cloth.

4Regularly rinse the water tank with water. Empty the water tank after

cleaning.

StorageIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

1 Make sure the plug has been removed from the wall socket and the iron has

cooled down. Set the steam control to position O.

2Empty the water tank (fig 17).

3Wind the mains cord round the cord storage facility.

4Store the iron standing on his heel in a safe and dry place (fig. 18).

Information & serviceIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

If you need information or if you have a problem, please visit the Philips Web site at

www.philips.com or contact the Philips Customer Care Centre in your country (you

will find its phone number in the worldwide guarantee leaflet). If there is no

Customer Care Centre in your country, turn to your local Philips dealer or contact

the Service Department of Philips Domestic Appliances and Personal Care BV.

TroubleshootingIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

This chapter summarises the most common problems you could encounter with

your iron. Please read the different sections for more details. If you are unable to

solve the problem, please contact the Philips Customer Care Centre in your country.

You can find its telephone number in the worldwide guarantee leaflet.

Solution(s)

Check if the plug is connected

to the wall socket properly.

Set the temperature control dial

to the required temperature.

Move the iron slightly and the

iron will start heating up again.

Fill the water tank (see 'Filling

the water tank').

Set the steam control dial to

position qor w(see 'Steam

ironing').

Set the temperature control dial

to a temperature suitable for

steam ironing (2to MAX).

Put the iron on its heel and wait

until the pilot light has gone out

before you start ironing.

Press and hold the steam

control dial for maximal 5

seconds.

Wait at least 1 minute before

using the Extra Steam function

again.

Set the temperature control dial

to a temperature between 3

and MAX. Put the iron on its

heel and wait until the pilot light

has gone out.

Fill the water tank (see 'Filling

the water tank').

Set the temperature control dial

to a temperature between 3

and MAX. Put the iron on its

heel and wait until the pilot light

has gone out.

Wait at least 1 minute before

using the Extra Steam function

again (see 'Extra Steam').

Fill the water tank (see 'Filling

the water tank').

Use the Calc-Clean function a

few times (see 'Calc-Clean').

Set the temperature control dial

to a temperature suitable for

steam ironing (2to MAX).

Put the iron on its heel and wait

until the pilot light has gone out

before you start ironing.

Empty the water tank and set

the steam control to position O

before storing the iron (see

'Storage'). Place the iron on its

heel.

Fill the water tank (see 'Filling

the water tank').

Possible cause(s)

There is a connection

problem.

The temperature

control dial has been

set to MIN.

The auto-off function is

activated.

There is not enough

water in the water tank.

The steam control dial

has been set to position

The iron is not hot

enough.

The steam control dial

has not been pressed

long enough.

The Extra Steam

function has been used

too often in a short

period.

The iron is not hot

enough.

There is not enough

water in the water tank.

The iron is not hot

enough.

The Extra Steam

function has been used

too often in a short

period.

There is not enough

water in the water tank.

You have been using

hard water, which has

caused scale flakes to

develop inside the

soleplate.

The set temperature is

too low.

The iron has been put

in horizontal position

while there is still water

in the water tank.

There is not enough

water in the water tank.

Problem

The iron is plugged in

but the soleplate is

cold.

The iron does not

produce any steam.

The Extra Steam

function does not work

(type GC1580)

Water leaks from the

soleplate when I use

the Extra Steam

function (type GC1580)

The spray function does

not work

Flakes and impurities

come out of the

soleplate during ironing.

Water leaks from the

soleplate during ironing.

Water leaks from the

soleplate while the iron

is cooling down or after

it has been stored.

The Shot of steam

function does not work

(type GC1575).

4239.000.5257.3

3/9

Specyfikacje produktu

Marka:	Philips
Kategoria:	Żelazo
Model:	Comfort Plus GC1575

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Philips Comfort Plus GC1575, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Żelazo Philips

Philips PerfectCare GC9223 Instrukcja

10 Stycznia 2025

Philips PerfectCare Silence GC9550 Instrukcja

10 Stycznia 2025

Philips 5000 Series DST5041 Instrukcja

2 Stycznia 2025

Philips 5000 Series DST5031 Instrukcja

2 Stycznia 2025

Philips 2000 Series DST2030 Instrukcja

2 Stycznia 2025

Philips PerfectCare Xpress GC5020 Instrukcja

2 Stycznia 2025

Philips GC097 Instrukcja

2 Stycznia 2025

Philips GC7020 Instrukcja

1 Stycznia 2025

Philips Azur Excel Plus HI565 Instrukcja

1 Stycznia 2025

Philips Comfort LongLife GC1621 Instrukcja

1 Stycznia 2025

Instrukcje Żelazo

Najnowsze instrukcje dla Żelazo

Livoo DOM402 Instrukcja

15 Stycznia 2025

Klarstein 10006681 Instrukcja

14 Stycznia 2025

Westinghouse WHIR01WB Instrukcja

13 Stycznia 2025

Calor Primagliss FV2560C0 Instrukcja

12 Stycznia 2025

Bomann DBS 762 CB Instrukcja

12 Stycznia 2025

Comelec PV1403 Instrukcja

12 Stycznia 2025

Comelec PV1406C Instrukcja

12 Stycznia 2025

Morphy Richards Speed Steam 333202 Instrukcja

8 Stycznia 2025

Yamazen ZAE-100 Instrukcja

7 Stycznia 2025

Brentwood MPI-69BKRG Instrukcja

6 Stycznia 2025