Instrukcja obsługi Perlick HC24TB-4-2R-2
Perlick
Dotknij systemu
HC24TB-4-2R-2
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Perlick HC24TB-4-2R-2 (2 stron) w kategorii Dotknij systemu. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2

SUPPORT
-Plastic Putty Knife
NOTE: Changing the door mount is not advisable if you have a door with custom wood overlay.
-Hinge Kit from Perlick
-Regular Phillips-Head Screwdriver
PROCEDURE FOR SWITCHING DIRECTION OF DOOR SWING
ON PERLICK C-SERIES, 15 INCH, AND SIGNATURE SERIES CABINETS
doing so may result in having a handle that is in an undesirable position.
Required:
-Large Flat-Head Screwdriver HINGE KITS
Part number 67439R to switch to Right Hinging
Part number 67439L to switch to Left Hinging
SCALE 1:24
3/28/2011DAS
SW
COPYRIGHT 2001 PERLICK CORPORATION. ALL RIGHTS RESERVED.
Milwaukee, WI 53223
DRAWN
Perlick Corporation
67439
OR MECHANICAL, INCLUDING PHOTOCOPYING, RECORDING, OR USED IN ANYINFORMATION STORAGE, TRANSMISSION, OR RETRIEVAL SYSTEM, WITHOUT WRITTEN PERMISSION FROM THE PERLICK CORPORATION
REVERSAL
THIS DOCUMENT/PUBLICATION/SOFTWARE/DRAWING CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF THE PERLICK CORPORATION. IT MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM, ELECTRONIC
DOOR HINGE DATE
Step 1: Support door in
the open position as shown.
Remove Hinge Pin.
Step 2: Pull
door to the side,
then lower door.
Step 3: Remove
Top and Bottom
Hinge Brackets
and save the
screws for later.
Step 4: Remove the Hole Plugs
from the Top and Bottom Hinge
Bracket mounting holes. Then
place them in the holes on the
opposite side made vacant
in Step 3.
Step 5: Using the
screws from Step 3,
install the new Top
and Bottom Cabinet
Hinge Brackets.
Save the screws
for later.
Plunger Bracket.
Step 6: Remove
the Top and
Bottom Door
Hinge Brackets
and the Push

Step: 7 Remove the Front Panel
from the Door Assembly by
removing the inner mounting
screws, 4 per side, from the
perimeter of the assembly.
Rotate the Front Panel 180°,
the top becomes the bottom.
Reattach using the same
screws and mounting holes.
SW
THIS DOCUMENT/PUBLICATION/SOFTWARE/DRAWING CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF THE PERLICK CORPORATION. IT MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM, ELECTRONIC
OR MECHANICAL, INCLUDING PHOTOCOPYING, RECORDING, OR USED IN ANYINFORMATION STORAGE, TRANSMISSION, OR RETRIEVAL SYSTEM, WITHOUT WRITTEN PERMISSION FROM THE PERLICK CORPORATION
COPYRIGHT 2001 PERLICK CORPORATION. ALL RIGHTS RESERVED.
Milwaukee, WI 53223
DRAWN
Perlick Corporation
67439
DOOR HINGE
REVERSAL
DAS 3/28/2011
SCALE 1:24
DATE
PROCEDURE FOR SWITCHING DIRECTION OF DOOR SWING
ON PERLICK C-SERIES, 15 INCH, AND SIGNATURE SERIES CABINETS
Corner
screws do not need
to be removed to
remove Front Panel.
Step 8: Remove Perlick
nameplate from Door
Front using Plastic Putty
Knife. Install new Perlick
nameplate (included)
Step9: Insert
bearing into
Top Door
Hinge Bracket.
Step 10: Insert V-block
into Bottom Door
Hinge Bracket, see
NOTE below, and
attach with E-Clip.
NOTE:
ORIENTATION
Bottom View
6°
Push Plunger using
screws removed in
Step 6.
Step 11: Attach the
Top and Bottom
Door Hinges and
Step 12: Place Lower
V-Block into Lower
Cabinet Hinge with
notch parrallel to
cabinet.
Top View
Parrallel
Step 13: Lift the
Door Assembly and
insert top pin into
bearing. Then move
door toward cabinet
and align V-Blocks.
Step 14: Insert and tighten Lower
Hinge Pin to complete assembly.
Specyfikacje produktu
Marka: | Perlick |
Kategoria: | Dotknij systemu |
Model: | HC24TB-4-2R-2 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Perlick HC24TB-4-2R-2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Dotknij systemu Perlick

7 Października 2024

7 Października 2024

7 Października 2024

7 Października 2024

7 Października 2024

7 Października 2024

7 Października 2024

7 Października 2024

7 Października 2024

7 Października 2024
Instrukcje Dotknij systemu
- Dotknij systemu Hoshizaki
- Dotknij systemu Caso
- Dotknij systemu Tefal
- Dotknij systemu Philips
- Dotknij systemu Livoo
- Dotknij systemu Danby
- Dotknij systemu Fisher & Paykel
- Dotknij systemu Bomann
- Dotknij systemu Klarstein
- Dotknij systemu Hestan
- Dotknij systemu Continental Edison
- Dotknij systemu Princess
- Dotknij systemu Innoliving
- Dotknij systemu DCS
- Dotknij systemu Marvel
- Dotknij systemu Summit
- Dotknij systemu SEB
- Dotknij systemu Edgestar
- Dotknij systemu Lynx
- Dotknij systemu Turbo Air
- Dotknij systemu Avantco
- Dotknij systemu Beverage-Air
Najnowsze instrukcje dla Dotknij systemu

1 Stycznia 2025

25 Grudnia 2024

20 Grudnia 2024

11 Grudnia 2024

9 Października 2024

9 Października 2024

9 Października 2024

9 Października 2024

9 Października 2024

9 Października 2024