Instrukcja obsługi Perlick 3076

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Perlick 3076 (6 stron) w kategorii Niet gecategoriseerd. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/6
Installation Instructions
Air-Cooled Wall Mount Beverage Dispenser
Form No. Z2507
Rev. 11.30.2022
Air Cooled Wall Mount Dispenser Installation Instructions
2
Installation of Air cooled Wall Mount Dispenser
1. Remove screws which
secure the back plate
to the dispenser.
3. Remove screws which
secure the bottom plate to
the dispenser.
Remove bottom plate and
set aside.
Parts Bag Included with Tower:
2. Remove back
plate and set aside.
Preparing for Installation:
Black Poly-tape Clear poly-tape
Elbow drain
tting with
barbed tailpiece
Straight drain
tting with
barbed tailpiece Spanner wrench
Parts bag contents include –
Included with Tower:
Wall Mount Dispenser
(Faucets and tap handles
shown are not included)
Mounting Bracket
Other Parts Needed for Installation: The parts required will vary depending on the installation.
PART NO. DESCRIPTION
C26609 Wall Mounted Air Shaft Connector, Cooler (1 required)
1655R Blower Kit, 134 CFM
C15365-1 3” Hose duct, blower to air shaft inside cooler - 12.5 feet
C15365-2 3” Hose duct, blower to air shaft inside cooler - 25 feet
C15366-1 Coupling Sleeve for 3” air shaft tube (1 required when joining two 12” sections)
C31573 Poly housing hanger strap kit
61082-1 Aluminum housing hanger
1390D 1/2” I.D. Vinyl Drain Tube – Anti-Microbial
Air Cooled Wall Mount Dispenser Installation Instructions
Form No. Z2507
Rev. 11.30.2022
3. Determine mounting location for dispensing
unit on wall.
Secure bracket to the wall.
Note: Align screws with as many wall studs
as possible to provide adequate support for
the dispenser.
After installing one screw, check to insure the
bracket is perfectly level before installing
remaining screws.
Note: Use mounting screws and anchors if
needed which are appropriate for the wall the
dispenser is to be installed on.
4. Hang back plate on the installed hanging track
making sure the plate is centered on the track.
Trace holes onto wall.
Remove back plate and set aside.
5. Measure to locate the exact center of each hole
location.
Mark centers.
6. Cut holes for air tube and beverage leads with
a 3-1/2” to 4” hole saw. The hole is larger than the
diameter of the air inlets on the dispensing units
to provide clearance when lowering the dispenser
into position.

Specyfikacje produktu

Marka: Perlick
Kategoria: Niet gecategoriseerd
Model: 3076

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Perlick 3076, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niet gecategoriseerd Perlick

Perlick

Perlick 4414-230-2 Instrukcja

7 Października 2024
Perlick

Perlick FR60RT-BS-STK Instrukcja

7 Października 2024
Perlick

Perlick 4414QC-2 Instrukcja

7 Października 2024
Perlick

Perlick FR24RT-BS-STK Instrukcja

7 Października 2024
Perlick

Perlick 4420 Instrukcja

7 Października 2024
Perlick

Perlick FR36RT-SS-STK Instrukcja

7 Października 2024
Perlick

Perlick FR24 Instrukcja

7 Października 2024
Perlick

Perlick 4420QC-2 Instrukcja

7 Października 2024
Perlick

Perlick FR48 Instrukcja

7 Października 2024

Instrukcje Niet gecategoriseerd

Najnowsze instrukcje dla Niet gecategoriseerd

V-TAC

V-TAC VT-7808 Instrukcja

7 Października 2024
V-TAC

V-TAC VT-7804 Instrukcja

7 Października 2024
V-TAC

V-TAC VT-15545 Instrukcja

7 Października 2024
D-Jix

D-Jix M-Usik Instrukcja

7 Października 2024
Black Hydra

Black Hydra GAMMA-625C Instrukcja

7 Października 2024
Palmer

Palmer PB 10 Instrukcja

7 Października 2024
Palmer

Palmer ABO Instrukcja

7 Października 2024
CRUX

CRUX SOOGM-16K Instrukcja

7 Października 2024
Sitecom

Sitecom CA-1001 Instrukcja

7 Października 2024