Instrukcja obsługi Paradigm Prestige 25S

Paradigm głośnik Prestige 25S

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Paradigm Prestige 25S (52 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/52
TM
S e r i e s O w n e r s M a n u a l
REFERENCE COLLECTION
Paradigm DOES NOT supply hardware for mounting Paradigm Prestige 25S
speakers to the wall. Always use screws appropriate for wall type and
weight of speakers.
If installing into drywall, install into 1/2˝ (13 mm) or 5/8˝ (16 mm) drywall
only. Screws must be long enough to go through anchor bolts (not supplied)
and
firmly into drywall.
IMPORTANT! READ BEFORE WALL-MOUNTING PARADIGM
PRESTIGE 25S SURROUND/REAR SPEAKERS:
Wall mount your Paradigm Prestige 25S speakers securely enough that they
cannot fall and cause personal injury or damage to property.
NON LIABILITY: We are aware that the mounting assemblies provided for speakers
in this manual could be used for purposes and in ways other than those for which
they were intended. The manufacturer, distributor, retailer and their respective agents
cannot be held responsible or liable for injuries or property damage—direct, indirect
or consequential—arising from the use of or inability to use these products safely
and properly. Every effort has been made to provide accurate, error-free installation
instructions. Paradigm Electronics Inc. disclaims liability for difficulties that may arise
from the misinterpretation of information contained in these instructions.
RECYCLING AND REUSE GUIDELINES (Europe)
In accordance with the European Union WEEE (Waste Electrical and Electronic Equipment) directive
effective August 13, 2005, we would like to notify you that our speakers may contain regulated
materials which, upon disposal, require special reuse and recycling processing. For this reason
Paradigm Electronics Inc. (the manufacturer of Paradigm speakers and Anthem electronics prod-
ucts) has arranged with its distributors in European Union member nations to collect and recycle
this product at no cost to you. To find your local distributor please contact the dealer from whom
you purchased this product or go to our website at paradigm.com.
Please note that only the product falls under the WEEE directive. When disposing of packaging and
other shipping material we encourage you to recycle through the normal channels.
p a r a d i g m . c o m
MAN0099 | 012815
Paradigm Electronics Inc.,
205 Annagem Boulevard,
Mississauga, ON, Canada L5T 2V1
PARADIGM, PARADIGM REFERENCE COLLECTION, PRESTIGE and all associated proprietary and
patented designs and technologies are registered trademarks of Paradigm Electronics Inc. Copyright
© Paradigm Electronics Inc. All rights reserved. All other trademarks are the property of their
respective owner(s). Paradigm Electronics reserves the right to change specifications and/or features
without notice as design improvements are incorporated.
INTRODUCTION
Thank you for purchasing Paradigm ® Prestige™ Series speakers; we are confident that
you will hear a stunning difference in your music and home theater system listening
experience.
Paradigm’s Comprehensive R&D, leading-edge technology, use of the finest materials
and sophisticated manufacturing and quality control techniques provide vastly superior
performance for each component part and at every stage of design. Paradigm ® Prestige™
speakers will provide you with unparalleled listening pleasure for many years to come.
To achieve all of the exceptional sound that these speakers are capable of providing
requires care in installation and operation. Please take the time to read this manual and
follow all instructions. If you have further questions, contact your Authorized Paradigm ®
Reference Collection Dealer or visit the Frequently Asked Questions page in the Support
section of our website at paradigm.com.
1
TABLE OF CONTENTS
Introduction 1........................
Unpacking Instructions (Floorstanding
Speakers) Securing Rubber Feet (Floor)
or Spikes (Carpet) ................... 2
General Tips ....................... 3
Break in . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Cleaning 3. . . . . . . . . . . . . . . . . . . . . . . . . . .
Preventing Speaker Damage 3. . . . . . . . .
Amplifier Distortion — The #1 Culprit! . . 3
More Powerful Amplifiers are Safer 3 . . .
Volume Control 3. . . . . . . . . . . . . . . . . . . . .
There is a Limit! . . . . . . . . . . . . . . . . . . . . 4
The Right Amount of Power 4 . . . . . . . . . .
Your Listening Room 4. . . . . . . . . . . . . . . .
Stand Mounting (Optional) ............ 5
Attaching Bumper Pads to Bookshelf/
Center/Surround Speakers 6. . . . . . . . . .
Bookshelf and Center Speakers 6. . . . . . .
Surround Speakers . . . . . . . . . . . . . . . . . 6
Placement: Front Left &
Right Speakers 7.....................
Accurate Timbre 8. . . . . . . . . . . . . . . . . . . .
Balanced Bass . . . . . . . . . . . . . . . . . . . . . 9
Optimal Imaging . . . . . . . . . . . . . . . . . . . 10
Optional On-Wall Mounting
of Front Speakers 10. . . . . . . . . . . . . . . . . .
Placement: Center Speaker 11. . . . . . . . . .
Placement: Surround / Rear Speakers . 12
5.1 Surround Configuration 12. . . . . . . . . .
7.1 Surround Configuration 12. . . . . . . . . .
Wall-Mounting 12. . . . . . . . . . . . . . . . . . . . .
Stand Mounting 12. . . . . . . . . . . . . . . . . . . .
Speaker Connection . . . . . . . . . . . . . . . 13
Minimum Gauge Requirements . . . . . . 13
Standard Connection for Prestige 15B . . 14
Standard Connection for All Speakers
(Except Prestige 15B) . . . . . . . . . . . . . . . . 15
Bi-Wire Connection . . . . . . . . . . . . . . . . 16
Bi-Amp Connection . . . . . . . . . . . . . . . . 17
Horizontal Bi-Amplification 18. . . . . . . . . .
Horizontal Bi-Amplification 18. . . . . . . . . .
Fine Tuning 18.......................
Basic Troubleshooting . . . . . . . . . . . . . 19
Specifications 20 .....................
Limited Warranty 23 . . . . . . . . . . . . . . . . . .
2
UNPACKING INSTRUCTIONS (FLOORSTANDING SPEAKERS)
Securing Rubber Feet or Spikes (Floor) (Carpet)
180°
OR
4
123
5 6
T M
Floor (Wood or Tile)
Floor (Wood or Tile)
Carpet
Carpet
Turn Key to Level Speaker
180°
180°
IMPORTANT! Follow These Steps Before Proceeding!
IMPORTANT! When removing the speaker from the carton, ensure
belt buckles, rings or other jewellery do not come into contact with
the speaker and scratch the finish.
3
GENERAL TIPS
Break-In
Although Paradigm Prestige speakers sound great “out of the carton,” they will sound
even better once they are “broken in.” Allow them to play for several hours before you
begin any critical listening.
NOTE: If your speakers have been transported or stored in the cold, let them warm to
room temperature before use.
Cleaning
Prestige speakers have a durable premium finish. To clean, use a damp soft cloth. Do not
use a strong or abrasive cleaner. Avoid getting any part of the speaker system wet. Do not
place wet objects (drinking glasses, potted plants, etc.) on top of the speakers—if allowed
to soak in, even a small amount of water may permanently damage the speaker enclosure.
PREVENTING SPEAKER DAMAGE
Paradigm Prestige speakers are efficient and can be driven to loud listening levels with
moderate amplifier power. They are also able to handle the output of very powerful
amplifiers. To prevent damage to your speakers, please read the following guidelines
before hooking them up.
Amplifier Distortion — The #1 Culprit!
Amplifier distortion is the principal cause of speaker damage. When listening at loud
levels your amplifier may run out of clean power. It will then begin to produce distorted
power several times greater than its rated output power. This will damage any brand of
speaker very quickly! (Ask your Dealer for amplifier recommendations.)
More Powerful Amplifiers are Safer
A 40 watt/channel amplifier will have substantial distortion above 40 watts. If driven to
50 watts, this amplifier will deliver distorted power—which will damage the speaker! A
100 watt/channel amplifier will have substantial distortion above 100 watts, but very low
distortion below 100 watts. Therefore, when the speaker requires 50 watts, this more
powerful amplifier will deliver clean power and speaker damage is less likely to occur.
Volume Control
Do not be fooled by the Volume Control of your receiver/preamplifier. It only adjusts
listening level—it is not a “power-output” dial. The amount of amplifier power actually
used at a given Volume Control setting depends solely on the nature of the music you
are listening to.
At a given Volume Control setting a quiet section of music will use less amplifier power
than a loud section. With typical pop-rock, jazz or large scale classical music, the rated
output power of many receivers/amplifiers is often reached when the Volume Control
is between the “11 and 1 o’clock” settings (with bass/treble and loudness controls not
used—otherwise rated power may be reached at even lower Volume Control settings).
4
PREVENTING SPEAKER DAMAGE (continued)
Remember, all amplifiers produce distortion when operated beyond their rated output
power. The resulting distortion will damage all speakers! Exercise caution! If you listen
at loud levels, be careful to listen for the point of audible distortion—if the speakers
begin to sound distressed turn the Volume Control down or your speakers and/or
amplifier(s) will be damaged! This type of damage constitutes abuse and is not covered
by the warranty. If louder volumes are desired, obtain a more powerful amplifier.
There is a Limit!
Although more powerful amplifiers are safer, there is a point at which you could have
more power than the speaker can handle. At that point you will overpower the speaker
and damage it. Exercise caution! At loud levels do not increase bass/treble controls
from zero and ensure that all loudness/contour/bass EQ buttons are off (otherwise rat-
ed output power will be reached at lower volume control settings). If you listen at loud
levels, watch for excessive visible cone excursion (grille movement) from the woofer—
then turn the Volume Control down.
The Right Amount of Power
A power-range rating is given as a guide to indicate the approximate minimum and
maximum power input of your Paradigm Prestige speakers. Amplifiers that exceed your
speaker’s power-range rating are recommended. Their greater power reserves provide
better sound. However, exercise caution! Use the speakers within their power-range
rating to prevent damage (keep listening levels below the point of excessive woofer
cone excursion).
YOUR LISTENING ROOM
Paradigm Prestige speakers are designed to provide superior high-end sound in a
wide variety of domestic settings. However, it is important to note that listening room
construction, dimensions and furnishings all play a part in the quality of sound you
will ultimately achieve. Your listening room will impose its own character on the
performance capabilities of any speaker system. The extra care you take in correctly
positioning the speakers will result in greater listening enjoyment. Keep the following
guidelines in mind when deciding on the best.
• Mid and high frequencies are affected by the amount of soft furnishings in your
room—curtains, carpets, sofas, wall coverings, etc. An excess of such items can
result in a somewhat dull sound. The same room without any soft furnishings can
produce a bright overall sound. The typical quantity of soft furnishings found in most
living situations provide the right acoustic characteristics to allow the speakers to
sound balanced;
• Concrete floors and walls tend to aggravate low-frequency standing wave problems
and are less preferred;
• Rooms where height, width and length are similar should be avoided as they can
exhibit significant low-frequency standing wave problems. This may result in reduced
clarity. If no other room is possible, experiment with speaker placement to minimize
acoustic problems.
5
STAND MOUNTING (optional)
The Paradigm Prestige 55C and Prestige 45C center channel speakers can be mounted
to Paradigm’s J-18C stand if desired. Ask your Paradigm dealer for details.
Stand Mounting a Center Channel Speaker (Prestige 55C Shown)
6
ATTACHING BUMPER PADS TO BOOKSHELF/CENTER/
SURROUND SPEAKERS
Bookshelf and Center Speakers
Self-adhesive bumper pads (included) should be applied to the bottom corners of
Paradigm Prestige bookshelf and center-channel speakers (see illustrations below)
when placed on a shelf or other flat surface. This will isolate your speakers from the
solid surface, improving overall sound quality.
NOTE: As an alternative, you may choose to stand mount your Paradigm Prestige 15B
bookshelf speakers using Paradigm stands. Ask your Paradigm dealer for details.
Surround Speakers
As an option, you may choose to apply the self-adhesive bumper pads to the back of the
Paradigm Prestige 25S surround speaker. This application prevents acoustic resonance
from the wall your speaker is mounted to.
Bookshelf Speaker
(Prestige 15B Shown)
Center Channel Speaker
(Prestige 55C Shown)
IMPORTANT! To prevent damage to your speaker’s finish, place the top
side of your speaker on a soft surface (rug, blanket, etc.) before applying
the bumper pads to the bottom side corners.
8
PLACEMENT: FRONT LEFT & RIGHT SPEAKERS (continued)
Accurate Timbre
For the most accurate and natural timbre, place front speakers so that their high-
frequency drivers are approximately at ear level, as shown below.
Placing bookshelf models on Paradigm speaker stands (sold separately) or bookshelves
raises their high-frequency drivers to approximately ear level, thereby ensuring the
best performance possible.
9
Balanced Bass
Placing front speakers in corners will over-emphasize bass and reduce overall clarity.
Avoid corner placement. Position front speakers 8 in (20 cm) or more from the wall
behind the speaker and as much as possible from either side wall, as shown below.
This will ensure better bass performance and optimal midrange clarity.
8 in (20 cm)
or more
As far away
from the wall
as possible
10
PLACEMENT: FRONT LEFT & RIGHT SPEAKERS (continued)
Optimal Imaging
Measure the distance from your main listening area to the front speakers (“X”). For
best imaging, place speakers from three-quarters of that distance up to that same
distance from each other (3/4 of “X” to “X”), as shown. To further optimize imaging,
toe speakers slightly inward so they point toward the listening position with their axes
crossing just behind it, as shown.
Optional On-Wall Mounting of Front Speakers
Follow the directions for placement given under “Optimal Imaging” above and use the
mounting instructions provided with your mounting brackets (sold separately) to safely
and securely mount your speakers on the wall.
3/4 “x”
“x”
11
PLACEMENT: CENTER SPEAKER
Paradigm Prestige Series center channel speakers are designed to cover a large,
wide listening area, allowing listeners throughout the room to hear center-channel
information with unprecedented clarity and intelligibility.
Placing your center-channel speaker below (or above) the TV will ensure the best
possible clarity and intelligibility. Position the speaker flush with the front of the TV
or speaker shelf to minimize unwanted sound reflections. Make sure the center-
channel is approximately the same distance away from the primary listening position
as your front speakers. (Some A/V receivers/processors can electronically adjust for
differences in distance.)
12
PLACEMENT: SURROUND / REAR SPEAKERS
5.1 Surround Configuration
Position one speaker on each side of the listening area, as shown below.
7.1 Surround Configuration (adds two rear speakers to a typical 5.1 surround configuration)
Position speakers behind the listening area—one speaker slightly right and the other
slightly left, as shown.
Wall Mounting
For wall mounting instructions for the Paradigm Prestige 25S, refer to the Wall Mounting
Instructions included with the speaker.
Stand Mounting
For stand mounting instructions for the Paradigm Prestige 25S, refer to the Stand
Mounting Instructions included with an optional Paradigm J-Series stand. Ask your
Paradigm dealer for details.
90˚
110˚
90˚
110˚
14
SPEAKER CONNECTION (continued)
Standard Connection for Prestige 15B
Your speakers’ binding posts can be used with banana, pin or spade connectors, as
well as with bare wire. Tighten the posts firmly by hand but do not over tighten!
Correct polarity (or phase) is critical for proper soundstage imaging and bass performance.
Connect one speaker at a time to ensure proper connection of every channel. The red (+)
amplifier terminal must be connected to the red (+) speaker terminal. The same applies
to the black (–) terminals. Make sure all wires are firmly fastened. Repeat this connection
procedure for each speaker in your system.
NOTE: If you hear a distinct lack of bass and a dislocated stereo image then one or
more of your speakers may be connected out of phase (polarity is reversed). Re-check
to ensure that each speaker’s cable is connected with correct polarity: red (+) to red
(+) and black (–) to black (–).
- +
15
Standard Connection for All Speakers (Except Prestige 15B)
All Paradigm Prestige speakers (except Prestige 15B) have two sets of input terminals
connected externally with jumper bars. These speakers can be bi-wired or bi-amplified
to achieve even better performance.
For standard connection of speakers with two input terminals, leave the jumper bars
attached and connect using either set of input terminals.
DO NOT attempt to bi-wire or bi-amplify speakers unless you have
removed the jumper bars.
- +
16
SPEAKER CONNECTION (continued)
Bi-Wire Connection
Bi-wiring can improve clarity and openness with less grain and more solidity to the bass.
Two speaker cables are required for each speaker that is bi-wired.
- +
REMOVE JUMPER BARS
BEFORE BI-WIRING
17
Bi-Amp Connection
IMPORTANT! When bi-amping, always use amplifiers with identical gain. If uniform
amplifier gain is not maintained the speaker-to-speaker balance will be incorrect
when vertically bi-amped, or the speaker system’s frequency balance will be incorrect
when horizontally bi-amped. To prevent problems, use identical amplifiers (brand and
model). Make sure they are operating in the same non-bridged or bridged mode.
- +- +
REMOVE JUMPER BARS
BEFORE BI-AMPING
18
SPEAKER CONNECTION (continued)
Passive bi-amping offers a dramatic improvement in clarity, openness and detail, with much
better bass solidity and definition. The presentation of music and movie soundtracks is
simply more intelligible and transparent.
With passive bi-amping, the speaker’s internal passive crossovers remain connected.
An external electronic crossover is not required and cannot be used (there is no direct
electrical access to individual drive units). This saves expense and setup difficulties. Passive
bi-amping optimizes your speaker to achieve the best possible high-end performance.
To bi-amplify, two power amplifiers are required. Connection can be either vertical
or horizontal.
Horizontal Bi-Amplification
Horizontal Bi-Amplification dedicates one amplifier to your (shown on previous page)
speakers’ mid/low-frequency inputs and another to their high-frequency inputs. This
configuration can maintain better clarity when listening at loud levels—if low-frequency
demands cause amplifier clipping, distortion will still be kept away from high-frequency
drivers. Connect your speakers to one amplifier at a time.
Vertical Bi-Amplification
Vertical Bi-Amplification dedicates one amplifier to each speaker. This (not shown)
configuration provides complete channel separation, which optimizes your system’s
imaging ability. Connect your speakers to one amplifier at a time.
FINE TUNING
Once you have your speakers positioned in the room and have set speaker distances and
calibrated speaker levels through your A/V Processor or A/V Receiver, it’s time for a little
fine tuning.
Following the instructions in this Owner’s Manual, once you have your speakers
positioned in the room and have set speaker distances and speaker level calibration
with your A/V Processor or A/V Receiver, it’s time for a little fine tuning.
Since Paradigm Prestige ™ speakers are designed to provide exceptional high-end
performance in a variety of room settings, fine tuning is simply a matter of making slight
adjustments to their placement in the room, if necessary.
Start with just the front speakers and listen to familiar music in stereo. The soundstage
will be both wide and deep, but this can be tuned to your personal preference by adjusting
the toe-in (the amount the speakers are turned toward the listening area). More toe-in
will increase image depth and localization; less toe-in will increase image width. Adjust
the toe-in in small increments, listening each time, until you achieve the soundstage
balance you prefer.
Toe-in is not applicable to the other speakers in your system since their position and
sound distribution pattern is fixed.
Fine tuning for the center channel is simply a matter of making level adjustments that
may be required for any particular multichannel music or movie program. If required,
adjust A/V Processor or A/V Receiver levels to ensure that there is always a cohesive
overall soundstage.
20
SPECIFICATIONS
Design
Crossover
High-Frequency Driver
Midrange Driver
Bass/Midrange Drivers
Bass Driver
Low-Frequency Extension*
Frequency Response:
On-Axis
30º Off-Axis
Sensitivity
– Room/Anechoic
Suitable Amplifier
Power Range
Maximum Input Power**
Impedance
Dimensions (h x w x d)†
Weight (unpacked)
Finish:
Gloss
Satin
4-driver, 2-1/2 way
floorstanding
2nd order electro-acoustic at
2.0 kHz (tweeter/mid); 2nd order
@ 400 Hz (mid/bass)
1” (25 mm) X-PAL™ dome,
ferro-fluid damped / cooled,
Perforated Phase Alignment
(PPA™) tweeter lens
N/A
8” (203 mm) X-PAL™ driver,
overmolded Active Ridge
Technology (ART™) surround,
IMS/SHOCK-MOUNT™
Two 8” (203 mm) X-PAL™
drivers, overmolded Active Ridge
Technology (ART™) surrounds,
IMS/SHOCK-MOUNT™
24 Hz
+/- 2 dB from 37 Hz to 20 kHz
+/- 2 dB from 37 Hz to 17 kHz
94 dB / 91 dB
15 - 450 watts
240 watts
Compatible with 8 ohms
44” x 9-1/4” x 14-3/4”
111.8 cm x 23.5 cm x 37.5 cm
68 lb (31 kg) each
Piano Black & Midnight Cherry
Walnut & Black Walnut
4-driver, 2-1/2 way
floorstanding
2nd order electro-acoustic at
2.0 kHz (tweeter/mid); 2nd
order @ 500 Hz (mid/bass)
1” (25 mm) X-PAL™ dome,
ferro-fluid damped / cooled,
Perforated Phase Alignment
(PPA™) tweeter lens
N/A
6.5” (165 mm) X-PAL™ driver,
overmolded Active Ridge
Technology (ART™) surround,
IMS/SHOCK-MOUNT™
Two 6.5” (165 mm) X-PAL™
drivers, overmolded Active Ridge
Technology (ART™) surrounds,
IMS/SHOCK-MOUNT™
29 Hz
+/- 2 dB from 40 Hz to 20 kHz
+/- 2 dB from 40 Hz to 17 kHz
93 dB / 90 dB
15 - 350 watts
200 watts
Compatible with 8 ohms
40” x 8-1/8” x 12-1/2”
101.6 cm x 20.6 cm x 31.8 cm
57 lb (26 kg) each
Piano Black & Midnight Cherry
Walnut & Black Walnut
Prestige 95F Prestige 85F
* DIN 45 500. Indicates -3 dB in a typical listening room.
** With typical program source provided the amplifier clips no more than 10% of the time.
† Add 1-1/8” or 2.9 cm to account for the depth of terminal posts (does not include Prestige 25S).
2121
4-driver, 2-1/2 way
floorstanding
2nd order electro-acoustic at
2.0 kHz (tweeter/mid); 2nd
order @ 500 Hz (mid/bass)
1” (25 mm) X-PAL™ dome,
ferro-fluid damped / cooled,
Perforated Phase Alignment
(PPA™) tweeter lens
N/A
5.5” (140 mm) X-PAL™ driver,
overmolded Active Ridge
Technology (ART™) surround,
IMS/SHOCK-MOUNT™
Two 5.5” (140 mm) X-PAL™
drivers, overmolded Active Ridge
Technology (ART™) surrounds,
IMS/SHOCK-MOUNT™
34 Hz
+/- 2 dB from 44 Hz to 20 kHz
+/- 2 dB from 44 Hz to 17 kHz
92 dB / 89 dB
15 - 220 watts
170 watts
Compatible with 8 ohms
36-1/4” x 7” x 10”
92.1 cm x 17.8 cm x 25.4 cm
47 lb (21.3 kg) each
Piano Black & Midnight Cherry
Walnut & Black Walnut
6-driver, 3 way centre channel
2nd order electro-acoustic
at 2.6 kHz (tweeter/mid),
2nd order @ 750 Hz
1” (25 mm) X-PAL™ domes,
ferro-fluid damped / cooled,
Perforated Phase Alignment
(PPA™) tweeter lens
3.5” (89 mm) X-PAL™ driver,
IMS/SHOCK-MOUNT™
Four 5.5” (140 mm) X-PAL™
drivers, overmolded Active Ridge
Technology (ART™) surrounds,
IMS/SHOCK-MOUNT™
N/A
37 Hz
+/- 2 db from 55 Hz - 20 kHz
+/- 2 db from 55 Hz - 17 kHz
94 dB / 91 dB
15 – 260 watts
190 watts
Compatible with 8 ohms
7-1/2” x 32” x 11-1/2”
19 cm x 81.3 cm x 29.2 cm
49 lb (22.2 kg)
Piano Black & Midnight Cherry
Walnut & Black Walnut
4-driver, 3 way center channel
2nd order electro-acoustic
at 2.8 kHz (tweeter/mid),
2nd order @ 700 Hz
1” (25 mm) X-PAL™ domes,
ferro-fluid damped / cooled,
Perforated Phase Alignment
(PPA™) tweeter lens
3.5” (89 mm) X-PAL™ driver,
IMS/SHOCK-MOUNT™
Two 5.5” (140 mm) X-PAL™
drivers, overmolded Active Ridge
Technology (ART™) surrounds,
IMS/SHOCK-MOUNT™
N/A
50 Hz
+/- 2 db from 75 Hz - 20 kHz
+/- 2 db from 75 Hz - 17 kHz
93 dB / 90 dB
15 - 220 watts
150 watts
Compatible with 8 ohms
7-1/2” x 18-3/8” x 10-1/2”
19 cm x 46.7 cm x 26.7 cm
32 lb (14.5 kg)
Piano Black & Midnight Cherry
Walnut & Black Walnut
Prestige 75F Prestige 55C Prestige 45C
22
SPECIFICATIONS (continued)
Design
Crossover
High-Frequency Driver
Midrange Driver
Bass/Midrange Drivers
Bass Driver
Low-Frequency Extension*
Frequency Response:
On-Axis
30º Off-Axis
Sensitivity
– Room/Anechoic
Suitable Amplifier
Power Range
Maximum Input Power**
Impedance
Dimensions (h x w x d)†
Weight (unpacked)
Finish:
Gloss
Satin
5-driver, 3 way surround
channel
2nd order electro-acoustic at
2.0 kHz (tweeter), 2nd order @
600Hz bass)
Two 1” (25 mm) X-PAL™ domes,
ferro-fluid damped / cooled,
Perforated Phase Alignment
(PPA™) tweeter lens
Two 3.5” (89 mm) X-PAL™
drivers, IMS/SHOCK-MOUNT™
N/A
6.5” (165 mm) X-PAL™ driver,
overmolded Active Ridge
Technology (ART™) surround,
IMS/SHOCK-MOUNT™
65 Hz
+/- 2 db from 125 Hz - 20 kHz
+/- 2 db from 125 Hz - 17 kHz
91 dB / 88 dB
15 - 180 watts
130 watts
Compatible with 8 ohms
8-5/8” x 16-1/4” x 6-1/2”
21.9 cm x 41.3 cm x 16.5 cm
17.6 lb (8 kg) each
Black
2-driver, 2 way bookshelf /
stand mounted
2nd order electro-acoustic at
2.0 kHz
1” (25 mm) X-PAL™ dome,
ferro-fluid damped / cooled,
Perforated Phase Alignment
(PPA™) tweeter lens
N/A esign
5.5” (140 mm) X-PAL™ driver,
overmolded Active Ridge
Technology (ART™) surround,
IMS/SHOCK-MOUNT™
N/A
42 Hz
+/- 2 db from 57 Hz - 20 kHz
+/- 2 db from 57 Hz - 17 kHz
90 dB / 87 dB
15 - 150 watts
90 watts
Compatible with 8 ohms
12-1/8” x 7” x 9-3/8”
30.8 cm x 17.8 cm x 23.8 cm
16 lb (7.3 kg) each
Piano Black & Midnight Cherry
Walnut & Black Walnut
* DIN 45 500. Indicates -3 dB in a typical listening room.
** With typical program source provided the amplifier clips no more than 10% of the time.
† Add 1-1/8” or 2.9 cm to account for the depth of terminal posts (does not include Prestige 25S).
Prestige 25S Prestige 15B
23
LIMITED WARRANTY
Paradigm® Prestige™ speakers covered in this manual are warranted to be and remain
free of manufacturing and/or material defects for a period of five (5) years from the
date of original purchase. Within the time period specified, repair, replacement or
adjustment of parts for manufacturing and/or material defects will be free of charge
to the original owner.
Thermal or mechanical abuse/misuse is not covered under warranty.
Limitations:
• Warranty begins on date of original retail purchase from an Authorized Paradigm ®
Dealer only. It is not transferable;
• Warranty applies to product in normal home use only. If product is subjected to any
of the conditions outlined in the next section, warranty is void;
• Warranty does not apply if the product is used in professional or commercial applications.
Warranty is Void if:
• The product has been abused (intentionally or accidentally);
• The product has been used in conjunction with unsuitable or faulty equipment;
• The product has been subjected to damaging signals, derangement in transport,
mechanical damage or any abnormal conditions;
• The product (including cabinet) has been tampered with or damaged by an unauthorized
service facility;
• The serial number has been removed or defaced.
Owner Responsibilities:
• Provide normal/reasonable operating care and maintenance;
• Provide or pay for transportation charges for product to service facility;
• Provide proof of purchase (your sales receipt given at time of purchase from your
Authorized Paradigm® Dealer must be retained for proof-of-purchase date).
Should servicing be required, contact your nearest Authorized Paradigm ® Dealer, Paradigm
Electronics Inc. or Import Distributor (outside the U.S. and Canada) to arrange, bring in
or ship prepaid, any defective unit. Visit our website, paradigm.com for more information.
Paradigm Electronics Inc. reserves the right to improve the design of any product without
assuming any obligation to modify any product previously manufactured.
This warranty is in lieu of all other warranties expressed or implied, of merchantability,
fitness for any particular purpose and may not be extended or enlarged by anyone. In no
event shall Paradigm Electronics Inc., their agents or representatives be responsible for
any incidental or consequential damages. Some jurisdictions do not allow limitation of
incidental or consequential damages, so this exclusion may not apply to you.
Retain this manual and your sales receipt for proof of warranty term and proof
of purchase.

Specyfikacje produktu

Marka: Paradigm
Kategoria: głośnik
Model: Prestige 25S

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Paradigm Prestige 25S, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Paradigm

Paradigm

Paradigm CI Home H65-A v2 Instrukcja

22 Lutego 2025
Paradigm

Paradigm CI Home H65-R v2 Instrukcja

22 Lutego 2025
Paradigm

Paradigm CI Home H65-IW v2 Instrukcja

21 Lutego 2025
Paradigm

Paradigm CI Home H55-R v2 Instrukcja

21 Lutego 2025
Paradigm

Paradigm CI Home H55-IW v2 Instrukcja

21 Lutego 2025
Paradigm

Paradigm CI Home H55-LCR v2 Instrukcja

21 Lutego 2025
Paradigm

Paradigm Cinema 100 CT Instrukcja

29 Września 2024
Paradigm

Paradigm CS-160 Instrukcja

29 Września 2024
Paradigm

Paradigm Monitor SE 3000F Instrukcja

29 Września 2024
Paradigm

Paradigm Studio CC-590 Instrukcja

29 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

LD Systems

LD Systems STINGER G3 TMB Instrukcja

8 Kwietnia 2025
JBL

JBL Conceal C83 Instrukcja

8 Kwietnia 2025
JBL

JBL Control 426LP Instrukcja

8 Kwietnia 2025
Crestron

Crestron SAROS ICE4T Instrukcja

7 Kwietnia 2025
Crestron

Crestron SAROS ICI6T Instrukcja

7 Kwietnia 2025
Crestron

Crestron SAROS IC8T Instrukcja

7 Kwietnia 2025
Focal

Focal K2 Power M FRAK Instrukcja

5 Kwietnia 2025
Turbosound

Turbosound PQ12-SB Instrukcja

3 Kwietnia 2025
Trust

Trust Tytan GXT 658 Instrukcja

3 Kwietnia 2025
Turbosound

Turbosound PQ15-YB Instrukcja

3 Kwietnia 2025