Instrukcja obsługi Panasonic PM2LF10

Panasonic nieskategoryzowany PM2LF10

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Panasonic PM2LF10 (1 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/1
INSTRUCTION MANUAL
CAUTIONS2
●
●
●
●
●
●
●
●
●
●
●
●
This product has been developed / produced for in-
dustrial use only.
A reverse supply protection circuit and output short-
circuit protection circuit are not incorporated. Since
wrong wiring may cause malfunction, make sure to
check the terminal arrangement, cable wiring and
power supply area before wiring.
Make sure that the power supply is o while wiring.
Verify that the supply voltage variation is within the rating.
If power is supplied from a commercial switching reg-
ulator, ensure that the frame ground (F.G.) terminal of
the power supply is connected to an actual ground.
Do not use during the initial transient time (50ms) af-
ter the power supply is switched on.
Do not run the wires together with high-voltage lines
or power lines or put them in the same raceway. This
can cause malfunction due to induction.
For the connector type, the cable length must be 2m,
or less, with 0.3mm2, or more, cable. If the cable is
extended for more than 2m, connect a capacitor of
10 F approx. between +V and 0V terminals. Fur-μ
ther, the cable type cannot be extended.
Avoid dust, dirt, and steam.
Take care that the sensor does not come in direct
contact with water, oil, grease, or organic solvents,
such as, thinner etc.
Take care that the sensor is not directly exposed to
uorescent lamp from a rapid-starter lamp or a high
frequency lighting device, as it may aect the sens-
ing performance.
If there is a reective object (conveyor, etc.) in the
background, since it may aect the sensing, use by
keeping enough distance from the reective object.
Thank you very much for purchasing Panasonic
products. Please read this Instruction Manual
carefully and thoroughly for the correct and
optimum use of this product. Kindly keep this
manual in a convenient place for quick reference.
SPECIFICATIONS1
Enclosure: Polycarbonate, terminal part (Connector type only): HSM (Ag plated)
Cable xing part (Cable type only): PBT
Material
0.2mm2 3-core cabtyre cable, 1m long (Cable type only) (Note 2)Cable
45 to 85% RH, Storage: 45 to 85% RHAmbient humidity
-10 to +55 (No dew condensation or icing allowed), Storage: -25 to +80℃ ℃
Ambient temperature
0.8ms or lessResponse time
Incorporated
Light-ON Dark-ON Dark-ONLight-ONDark-ONLight-ON
Over current protection
Output operation
Average: 25mA or less, Peak: 80mA or less
Current consumption
Output
5 to 24V DC 10% Ripple P-P 5% or lessSupply voltage ±
2.5 to 8mm (Convergent point 5mm) with white non-glossy paper (15 15mm) (Note 1)×  
NPN open-collector transistor
・Maximun sink current: 100mA
・Applied voltage: 30V DC or less (between output and 0V)
・Residual voltage: 1V or less (at 100mA sink current), 0.4V or less (at 16mA sink current)
Sensing range
L type (Top sensing)
PM2-LL10-C1
PM2-LL10
PM2-LL10B-C1
PM2-LL10B
Front sensing
PM2-LF10-C1
PM2-LF10
PM2-LF10B-C1
PM2-LF10B
Top sensing
PM2-LH10-C1
PM2-LH10
PM2-LH10B-C1
PM2-LH10B
Type
Model
No.
Cable
Connector type
Item
Notes: 1)
2)
Take care that, depending on the product, the sensing range may extend to 12.5mm maximum with white non-glossy paper.
The cable cannot be extended.
●If soldering is done directly on the terminals, strictly
adhere to the conditions given below.
Soldering temperature: 260 or less℃
Soldering time: 10 sec. or less
Soldering position: 1.5mm, or more, away from the sensor body.
SOLDERING (Connector type only)
4
1.5mm
Soldering position
0V OUT ＋V
●
When xing the sensor with screws, use M3 screws and
the tightening torque should be 0.49N m or less. Fur-・
thermore, use small, round type plain washers ( 6mm).φ
MOUNTING5
PM2 Series
Photoelectric Sensor
Micro-photosensor
This bag is a product made from polyethylene. Even if it burns, harmful gas is not generated.
●
●
Never use this product as a sensing device for personnel protection.
In case of using sensing devices for personnel protection, use products which meet
standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each
region or country.
WARNING
I/O CIRCUIT DIAGRAMS3
100mA max.
Color code of cable type
and mainting cable
(B
lack ) Output
(Blue
) 0V
(Brown) + V
Internal circuit
Users' circuit
Sensor circuit
Load
+
-
5 to 24V DC
±10%
INTENDED PRODUCTS FOR CE MARKING
6
●The models listed under ' SPECIFICA-
TIONS' come with CE Marking. As for all
other models, please contact our oce.
1
PRINTED IN JAPAN © Panasonic Electric Works SUNX Co., Ltd. 2011
Overseas Sales Division (Head Office)
2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan Phone: +81-568-33-7861 FAX: +81-568-33-8591
Europe Headquarter: Panasonic Electric Works Europe AG
Rudolf-Diesel-Ring 2, D-83607 Holzkirchen, Germany Phone: +49-8024-648-0
US Headquarter: Panasonic Electric Works Corporation of America
629 Central Avenue New Providence, New Jersey 07974 USA Phone: +1-908-464-3550
http://panasonic-electric-works.net/sunx

Specyfikacje produktu

Marka: Panasonic
Kategoria: nieskategoryzowany
Model: PM2LF10

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Panasonic PM2LF10, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany Panasonic

Panasonic

Panasonic VL-DM200BX Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic FV-SCGPW1 Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic VL-SDM200BX Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic VL-SW251CX Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic VL-SDM100BX Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic NA-F75S7 Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic DMW-LVF1E Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic F-60DHN Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic NC-EH40P Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic NA-F65B7 Instrukcja

31 Sierpnia 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024