Instrukcja obsługi Panasonic CY-111B-P

Panasonic nieskategoryzowany CY-111B-P

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Panasonic CY-111B-P (4 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
INSTRUCTIONS
Cylindrical Photoelectric Sensor
CY-111, CY-19 CY-12 Seriesq, q
Thank you for purchasing products from Panasonic. Please read this
Instruction Manual carefully and thoroughly for the correct and optimum
use of this product. Kindly keep this manual in a convenient place for quick
reference.
WARNING
●Never use this product as a sensing device for personnel protection.
●In case of using sensing devices for personnel protection, use prod-
ucts which meet laws and standards, such as OSHA, ANSI or IEC
etc., for personnel protection applicable in each region or country.
1Cautions
●This product has been developed / produced for industrial use only.
●This product is suitable for indoor use only. The cable extension up to
a total of 10m or less with a strength of 0.34mm
2 or less (each emitter
and receiver of the thru-beam type) is possible.
●Make a cable length as short as possible to lessen noise pickup.
●Make sure that the power supply is off while wiring.
●Verify that the supply voltage including the ripple is within the rating.
●If power is supplied from a commercial switching regulator, ensure that
the frame ground (F.G.) terminal of the power supply is connected to
an actual ground.
●Shortcircuiting the load or wrong wiring may burn or damage the
product.
●Ensure that an isolation transformer is utilized for the DC power sup-
ply. If an autotransformer is utilized, the main body or power supply
may be damaged.
●If the used power supply generates a surge, connect a surge absorber
to the power supply to absorb the surge.
●Do not use the sensor during the initial transient time (0.5 sec) after
the power supply is switched on.
●Do not run the wires together with high-voltage lines or power lines
or put them in the same raceway. This can cause malfunction due to
induction.
● Avoid using the product where there are strong magnetic elds as they
may prevent the product from working according to the specication.
● Take care that the sensor is not directly exposed to a uorescent lamp
from a rapid-starter lamp or a high frequency lighting device, as it may
affect the sensing performance.
●Protect the sensor from water, oil, grease, organic solvents such as
thinner, etc., strong acid, and alkaline.
●Avoid using a product where there is excessive vapor, dust or cor-
rosive gases, or in a place where it could be exposed directly to water
or chemicals.
● This product cannot be used in an environment containing inam-
mable or explosive gases.
●Never disassemble or modify the product.
2Compliance with standards and directives
This product complies with the following standards and
regulations.
●For the EU: EMC Directive 2004/108/EC
●For the US and Canada:
ANSI/UL60947-5-2, CAN/CSA C22.2 No.14
●For Korea: S1-G-1-2009, S2-W-5-2009
* In case you require a UL listing mark or C-UL
listing mark, use a class 2 power supply unit.
RoHS directive
●This equipment complies with RoHS (CE and Chinese
directive).
3Sensor types
Cable type (2m) Connector type (M12)
Standard
Side view
4Part description
124
3 3
1Main body
2Mounting plate
3Nut
4Cable with connector
5Mounting
General installation hints
1. Attach the sensor directly on your equipment or use one of the optional
mounting brackets to x the sensor.
2. The tightening torque should be 3Nm or less.
3. If you mount a M12 connector type, you can use the optional cable with
the connector UZZ812 D. The tightening torque for the connector part qq
should be 3Nm or less.
Mounting with the mounting bracket MS-CY1-1
1. Using the holes indicated
1, screw the mounting
bracket to the surface.
2. Feed the sensor into the
mounting hole and 2
afx it with the nuts on the
sensor.
1
2
Mounting with the mounting bracket MS-CY1-2
1. Using the holes indicated
1, screw the mounting
bracket to the surface.
2. Feed the sensor into the
mounting hole and 2
adjust its direction.
3. Use the upper two screws
3 to secure the sensor.
1
3
2
1
Model no. Description
MS-CY1-1 Material: Stainless steel
MS-CY1-2 Material: Plastic (recommended for a more exible beam axis
alignment)
6Mating cables
There are two types of mating cables: straight type and elbow type. You
only need mating cables for the connector type (M12).
Straight type Elbow type
Cable type Model no. Description
Straight
UZZ81220D Length: 2m
UZZ81250D Length: 5m
Elbow
UZZ81221D Length: 2m
UZZ81251D Length: 5m
7Reectors
Square form Hexagonal form
Reective tape
Reector form Model no. Description
Square RF-420 50 x 50mm
Hexagonal RF-410 24 x 21mm
Reective tape RF-40RL5 22 x 5m, thickness: 0.4mm
8Wiring diagrams
Emitter of thru-beam type
WR9'&
±％
9LROHW,QSXW
%OXH9
%URZQ9
Receiver of thru-beam / reective type (NPN)
±％
/RDG
WR9'&
%ODFN2XWSXW
%URZQ9
%OXH9
Receiver of thru-beam / reective type (PNP)
±'&％
/RDG
WR9
%URZQ9
%OXH9
%ODFNRXWSXW
9Terminal arrangement
M12 connector
1 2
4 3
Terminal no. Function
1+V
2Input (only emitter of thru-beam type)
30V
4Output (only receiver of thru-beam and reec-
tive type)
* Make sure to insulate the ends of all unused lead wires.
10 Detection curves
Thru-beam type
15
-15
15
15 m
10 m
cm
ø 12 mm
A
A = Sensing range
Diffuse reective type
5
1 5
cm
cm
10 cm
-1
1
A
1.4
-1.4
Object 10 x 10cm; 1= White 90%, = Gray 18%2
2
Diffuse reective type with adjustable sensitivity
80
cm
cm
60 cm
1.4
-1.4
1
-1
A
Object 10 x 10cm; 1= White 90%, = Gray 18%2
Retroreective type
4
4 m
10
-4
-10
A
m4
2
cm
With reector RF-420
Retroreective type with polarizing lters
2
2 m
4
6
-2
-4
-6
m
A
3
2
cm
E/R
0.2
With reector RF-420
11 Dimensions
CY-1q
a
b
M18
Cable type Connector type
a ( b (mm) a (mm) b (mm)mm)
Standard CY-
111qqq/121 /192
46 28 60 28
Standard CY-191q48 28 62 28
Side view CY-
111V q q q/121V / 191V
/192Vq
62 28 76 28
Standard CY-122q62 44 76 44
Side view CY-122Vq78 44 92 44
Mounting bracket MS-CY1-1
35
28
50
15
20
1
20
10
= =
= =
ø18.22.5
6.5
16.5
6.5
Mounting bracket MS-CY1-2
10
45
= =
25
55
248 8
5
27
19.5
ø18.2
6.5
Reector RF-420
51
69
8
47
60
35
4 - R5
8
2 - ø
2 - ø 4.5
5.5
ø4.5
51.5
3.5
Reector RF-410
4
29
45
9
21
33
==
24
ø7.5
ø4.5
7.5
3

Specyfikacje produktu

Marka: Panasonic
Kategoria: nieskategoryzowany
Model: CY-111B-P

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Panasonic CY-111B-P, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany Panasonic

Panasonic

Panasonic VL-DM200BX Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic FV-SCGPW1 Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic VL-SDM200BX Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic VL-SW251CX Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic VL-SDM100BX Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic NA-F75S7 Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic DMW-LVF1E Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic F-60DHN Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic NC-EH40P Instrukcja

31 Sierpnia 2024
Panasonic

Panasonic NA-F65B7 Instrukcja

31 Sierpnia 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024