Instrukcja obsługi Ozito PXRTS-018

Ozito Niesklasyfikowane PXRTS-018

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ozito PXRTS-018 (6 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
STANDARD EQUIPMENT
ON
OFF
MIN
SPEED
MAX
ON
OFF
MIN
SPEED
MAX
PXRTS-018
INSTRUCTION MANUAL
SPECIFICATIONS
Input: 18V
No Load Speed: 5,000-33,000/min
Collet Size: 2.3 & 3.2mm
Weight: 3.74kg
ozito.com.au
1222
Cordless Rotary Tool Station
Flexible Shaft & Accessory
Case
40 x Sanding Discs, Screw
Mandrel, 5 x Diamond
Engravers, 2 x Drum Mandrels,
Wire Brush, 2 x Drill Bits
(2.3 & 3.2mm), Polishing
Compound, 4 x Felt Wheels,
Cone Mandrel, 8 x Sanding
Bands, 5 x Cut-Off Wheels, 5
x Stone Grinders, 2 x Collets
(2.3 & 3.2mm) & Spanner
ROTARY TOOL
STATION
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
OZITO INDUSTRIES PTY. LTD. 25 Fox Drive, Dandenong South, Victoria, Australia 3175.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other than that specied
on the tool.
• If the tool shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty and are excluded from the warranty extension. Warranty excludes
consumable parts.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
ON
OFF
MIN
SPEED
MAX
1. Flexible Shaft
2. Flexible Shaft Connector
3. Storage Case
4. Storage Slots
5. Speed Dial
6. Battery Seating
7. Power Switch
8. Collet Nut
9. Rotary Tool Handle
10. Handle Storage
11. Spindle Lock
This tool is compatible with all batteries & chargers from the Ozito PXC range.
CORDLESS ROTARY TOOL STATION
BATTERY & CHARGER
KNOW YOUR PRODUCT
1. FITTING ACCESSORIES
SETUP & PREPARATION
2
3
4
5
1
11
8
9
10
7 6
WARNING! ENSURE THE TOOL IS SWITCHED
OFF AND THE BATTERY IS REMOVED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
Assembling the Flexible Shaft
1. Press the end of the exible shaft
connector rmly against the
square socket.
Note: Ensure the inner core
is ush with the socket before
tightening.
2. Screw the exible shaft connector onto the tool.
WARNING! ENSURE THAT THERE ARE NO KINKS
OR BENDS IN THE FLEXIBLE SHAFT BEFORE
OPERATION. OVER BENDING THE SHAFT CAN
GENERATE EXCESSIVE HEAT WHICH CAN DAMAGE
THE TOOL.
Attaching Accessories
1. Slide back and hold the spindle
lock.
2. Using the supplied wrench,
slightly loosen the collet nut.
3. Insert the shaft of the accessory
into the collet until only 2-3mm
of it is left out.
4. With the spindle lock engaged,
nger tighten the collet nut until
the accessory shank is rmly
gripped by the collet.
Note: Avoid excessive tightening of the collet nut when no accessory is
inserted, as this may cause the collet to get stuck in the collet nut. If this
happens, push the shank of an accessory into the hole of the collet nut.
HOLD
HOLD
HOLD
13CM
RADIUS
MAX.
ALLOWABLE
BEND
ON
OFF
INNER
CORE
a.
b.
2 ACCESSORY SELECTION
Cut-Off Wheels
Materials: plastics & soft metals.
These emery discs can be used for
shortening bolts, reslotting stripped
screwheads, cutting through small rods and
tubing or making rectangular holes in sheet
metal. Attach these to a screw mandrel for
use and replace them when worn.
1. Loosen and remove the small screw from the top of the screw mandrel.
Also remove one of the washers from the mandrel.
2. Slide a cut-off wheel onto
the mandrel, then replace the
washer and screw to hold the
disc in place.
Diamond Engravers
Materials: timbers, plastics, hard & soft
metals, jewellery, and scrimshaw.
These engravers have diamond particles
embedded and are ideal for ne detail
work on harder materials such as jewellery,
ceramic, hardened steel or glass. They can
also be used to touch up and nish surfaces.
Drill Bits
Materials: timbers, plastics and metals.
These are ideal for making small holes in
workpieces. Change out the collets to suit
the size of the drill bit shank.
Steel Brush
Materials: brass, copper, pewter,
aluminium, stainless steel.
The steel brushes are ideal for removing
rust and corrosion, polishing, deburring
and blending surfaces, as well as cleaning
electrical components.
Note: Allow the tips of the wire brushes to do the work. Do not apply
excessive pressure or use the sides of the bristles on the work surface as
this may cause the bristles to wear and break.
DISC
WASHER
WASHER
SCREW
MANDREL
5 x CUT-OFF
WHEELS
5 X DIAMOND ENGRAVERS
2 x DRILL BITS
(2.3 & 3.2MM)
STEEL BRUSH
Sanding Bands
Materials: timbers, plastics, soft metals.
Sanding bands can be used for shaping
wood, smoothing edges and sanding inside
curves. The drum mandrels allow you to
easily replace the sanding bands when they
become worn and lose their grit.
1. Using the small screwdriver on
the back of the spanner, loosen
the small screw on the drum
mandrel to contract the drum.
2. Slide a sanding band onto the
drum and retighten the screw to
hold the band in place.
WARNING! BEFORE EACH USE, ENSURE THAT THE
DRUM IS SUFFICIENTLY EXPANDED TO SECURE THE
BAND DURING USE. LOOSE ACCESSORIES MAY FLY
OFF AND CAUSE INJURY TO THE OPERATOR AND/
OR BYSTANDERS.
Sanding Discs
Materials: timbers, plastics, soft metals.
Sanding discs are good for smoothing and
shaping wood or breglass, stripping paint
and removing rust. The exible discs make
them good for sanding contoured surfaces
and hard to reach areas. Attach these to a
screw mandrel for use and replace them
when worn.
1. Loosen and remove the small screw from the top of the screw mandrel.
Also remove one of the washers from the mandrel.
2. Slide a sanding disc onto the
mandrel, then replace the washer
and screw to hold the disc in
place.
40 x SANDING
DISCS
SCREW
MANDREL
DISC
WASHER
WASHER

Specyfikacje produktu

Marka: Ozito
Kategoria: Niesklasyfikowane
Model: PXRTS-018

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ozito PXRTS-018, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Ozito

Ozito

Ozito PXBSPS-180 Instrukcja

6 Października 2024
Ozito

Ozito SSH-240 Instrukcja

6 Października 2024
Ozito

Ozito PXPPS-1820 Instrukcja

4 Października 2024
Ozito

Ozito PXNGS-218 Instrukcja

4 Października 2024
Ozito

Ozito PSR-5732U Instrukcja

3 Października 2024
Ozito

Ozito PXCLMLTC-418U Instrukcja

3 Października 2024
Ozito

Ozito PXDDK-301U Instrukcja

3 Października 2024
Ozito

Ozito WPHGK-2000U Instrukcja

3 Października 2024
Ozito

Ozito PXDDGK-600U Instrukcja

3 Października 2024
Ozito

Ozito PXCBLLTC-418U Instrukcja

3 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024