Instrukcja obsługi Ozito ETL-7530U

Ozito Niesklasyfikowane ETL-7530U

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ozito ETL-7530U (3 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

ELECTRIC

TILLER

750W 300mm

ORIGINAL INSTRUCTIONS

SPECIFICATIONS

Voltage: 230V~50Hz

Power Rating: 750W

No Load Speed: 400/min

Working Width: 300mm

Working Depth: 220mm max.

Tines: 4 x 220mm

Noise Level: 93dB(A)

Weight: 8.14kg

ETL-7530U

WHAT’S IN THE BOX

WARRANTY

1117

TILLER SAFETY WARNINGS

• Check all electrical cables for signs of damage or ageing. Replace

the cable if it is cracked, split or otherwise damaged.

• Check the condition of the cutting cylinder, and ensure that all

threaded connections are securely tightened.

• If the tines are blunt, have a power tool repairer inspect the tiller.

Tiller Motor & Switch

Upper & Lower Handle

Once per Season

GENERAL POWER TOOL SAFETY WARNINGS

ELECTRICAL SAFETY

Handle Fasteners

MAINTENANCE

• Lubricate the tines and shaft.

• At the end of the season, have the tiller checked and serviced at a

power tool repairer.

WARNING!: ENSURE THE TOOL IS SWITCHED OFF AND

DISCONNECTED FROM THE POWER SUPPLY BEFORE

PERFORMING ANY OF THE FOLLOWING TASKS.

Cleaning

CAUTION!: ENSURE ALWAYS CLEAN THE TILLER AFTER

USE. FAILURE TO CARRY OUT PROPER CLEANING CAN

RESULT IN DAMAGE TO THE TILLER OR CAUSE IT TO

MALFUNCTION.

Whenever possible, clean the tiller straight after you have finished

using it.

• Clean the underside of the housing around the tines, guard shield

and fender with a stiff brush. Then, using a soft cloth dampened

with a mild soap and water mixture wipe the underside. Never

splash with water!

• To remove soil and debris from the tines and transmission, use a

stiff brush or a dampened cloth.

• Clean the motor housing vents, and remove any remaining grass or

dirt.

• Once cleaned, wipe the tine and shaft dry and apply a light coat of

oil.

WARNING!: ENSURE INJURY CAN OCCUR DURING WORK

ON THE TINES. WEAR PROTECTIVE GLOVES.

OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG

All of our products undergo strict quality checks to ensure that they reach

you in perfect condition. In the unlikely event that your device develops a

fault, please contact our service department at the address shown on this

guarantee card. You can also contact us by telephone using the customer

service number shown. Please note the following terms under which

guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the

manufacturer mentioned below promises to buyers of its new products

in addition to their statutory guarantee claims are not affected by this

guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or

manufacturing faults on a product which you have bought from the

manufacturer mentioned below are limited to either the rectication of said

defects on the product or the replacement of the product, whichever we

prefer.

Please note that our devices are not designed for use in commercial, trade

or professional applications. A guarantee contract will not be created if the

device has been used by commercial, trade or industrial business or has

been exposed to similar stresses during the guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly

instructions or due to incorrect installation, a failure to follow the operating

instructions (for example connecting it to an incorrect mains voltage or

current type) or a failure to follow the maintenance and safety instructions

or by exposing the device to abnormal environmental conditions or by lack

of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example

overloading the device or the use or unapproved tools or accessories),

ingress of foreign bodies into the device (such as sand, stones or dust,

transport damage), the use of force or damage caused by external forces

(for example by dropping it).

- Damage to the device or parts of the device caused by normal or natural

wear or tear or by normal use of the device.

4. Your Product is guaranteed for a period of 36 months from the original

date of purchase and is intended for DIY (Do It Yourself) use only. Warranty

excludes consumable parts. Guarantee claims should be submitted

before the end of the guarantee period within two weeks of the defect

being noticed. No guarantee claims will be accepted after the end of the

guarantee period. The original guarantee period remains applicable to the

device even if repairs are carried out or parts are replaced. In such cases,

the work performed or parts tted will not result in an extension of the

guarantee period, and no new guarantee will become active for the work

performed or parts tted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST

RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR

Please refer to the restrictions of this warranty concerning wearing parts,

consumables and missing parts as set out in the service information in

these operating instructions.

CUSTOMER SERVICE HELPLINE

GB: 0151 294 4488

IRL: 1850 882711

Ozito-diy.co.uk

ozito-diy.co.uk

WARNING! “Read all safety warnings, instructions, illustrations and specications

provided with this power tool.” Failure to follow the warnings and instructions may result in electric

shock, re and/or serious injury.

Save all warnings and instructions for future reference. The term “power tool” in the warnings refers

to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b. Do not operate power tools in explosive atmospheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c. Keep children and bystanders away while operating a power tool. Distractions can cause you to

lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will

reduce risk of electric shock.

b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase

the risk of electric shock.

e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the inuence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce

personal injuries.

c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to

power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your

nger on the switch or energising power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g. If devices are provided for the connection of dust extraction and collection facilities, ensure

these are connected and properly used. Use of dust collection can reduce dust-related hazards.

h) Do not let familiarity gained from frequent use of tools allow you to become complacent and

ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

4. Power tool use and care

a. Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from

the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

e. Maintain power tools and accessories. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

5. Service

a. Have your power tool serviced by a qualied repair person using only identical replacement

parts. This will ensure that the safety of the power tool is maintained.

WARNING! When using mains-powered tools, basic safety precautions, including the

following, should always be followed to reduce risk of re, electric shock, personal injury and

material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency,

before operating the tool.

Save these instructions and other documents supplied with this tool for future reference.

Before you connect the equipment to the mains supply make sure that the data on the rating plate are identical

to the mains data.

This tool is double insulated therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid

a hazard.

Note: Double insulation does not take the place of normal safety precautions when operating this tool. The

insulation system is for added protection against injury resulting from a possible electrical insulation failure

within the tool.

Using an Extension Lead

Please only use power cables that are not damaged. The total length of the power cable should not exceed

40 meters; going beyond this distance will reduce the power output of the electric motor. The power cable

must have a cross-section of 3 x 1.5 mm2. The insulating sheath of lawn mower power cables is frequently

damaged.

Some of the causes for this are:

• Cuts caused by running over the cable

• Pinching when the power cable is dragging under doors and pulled through windows.

• Cracking due to old age of the insulation

• Kinking by improperly fastening or guiding the power cable.

The power cables must, at the very minimum, be of type HO5RN-F and 3-stranded. The cable type must

be printed somewhere on the power cable. Only purchase power cables that are marked as such! Plugs

and socket couplers for the power cables must be made from rubber and be splashproof. There is a limit to

how long power cables can be. Longer power cables require larger conductor cross-sections. Power cables

and connecting lines must be regularly checked for damage. Ensure that the lines are de-energized before

checking them. Completely unwind the power cable. Also check power cable entry points, plugs and socket

couplers for kinks.

• Read the operating instructions with due care. Familiarize yourself with the operator controls and proper operation of

the machine

• Never allow children or other persons who are not familiar with the operating instructions to use the machine. Contact

your local governmental agency for information regarding minimum age requirements for operating the machine

• Never work in the direct vicinity of persons - especially children - or animals.

• Always keep in mind that the machine operator or user is responsible for accidents involving other persons and/or

damage to their property.

Preliminary measures

• Always wear sturdy, non-slip footwear and long trousers when working. Never operate the machine barefoot or in

sandals.

• Check the ground on which the machine will be used and remove all objects that could be caught up and violently ung

out by it.

• Before using the machine, always visually examine the tools for excessive wear or damage. To prevent any imbalance,

replace worn out or damaged parts and mounting bolts as a set only.

• The power cables used are not to be of a lighter duty class than light rubber-insulated H05RN-F in accordance with DIN

57282/VDE 0282 and they must have a cross section of at least 1.5 mm2. The connection must be splash-proof. The

power cable must be fed through the stress-relief clips and be plugged into the switch/plug block. Before use, check the

cable for damage and signs of aging. Never use the machine with worn or damaged cables. If the cable is damaged

while working, pull the power plug immediately and only then inspect the damage. Do not touch the power cable until the

plug has been pulled. • Socket couplers to connection elements must be made from rubber, soft PVC or other thermal

material of equal rigidity or coated with such material.

• Make sure that all nuts, bolts and screws are tightened securely and that the machine is in safe working condition.

• The equipment may only be connected to a power supply protected by means of an earth-leakage circuit breaker (RCD)

with a maximum operating current of 30 mA.

Handling

• Work only in daylight or in good light.

• Always maintain good footing on inclines.

• Only operate the machine at a walking pace.

• Work perpendicular to the slope, never up or down it.

• Be particularly careful when you change direction on a slope.

• Do not work on overly steep inclines.

• Be particularly careful when you turn the machine around or pull it toward yourself.

• Switch on the motor carefully as described in the instructions from the manufacturer and ensure that you keep your feet

at a safe distance from the tool.

• Never move your hands or feet toward or under any rotating parts.

• Never lift or carry a machine whilst the motor is running; in addition the power plug should be pulled.

• Switch off the motor whenever you leave the machine unattended.

• If the machine begins to experience unusual vibrations, immediately switch it off and check it.

• Ensure that you avoid paths that could restrict the free movement of the extension cable.

• Keep cables away from the cutters. The cutters may cause damage to the cables and result in contact with active parts.

Maintenance and storage.

• Always make sure that all nuts, bolts and screws are tightened securely so that the machine is in safe working condition.

• Allow the motor to cool before you put the machine in an enclosed area.

• For your own safety, replace worn or damaged parts without delay.

• Switch the machine off and pull the power plug before carrying out any adjustment or cleaning work on it, and before

checking to see if the mains connection is entwined or damaged.

• Switch off the motor and pull the power plug:

- before you dislodge any blockages or clogs.

- before you clean the machine, inspect it or carry out work on the machine.

- after you have traveled over an obstacle.

- if you have struck a foreign object.

- if the equipment begins to experience exceptionally strong vibrations

• Do not touch damaged cables before disconnected from the power supply. Touching a damaged cable may result in

contact with active parts.

• Do not touch the cutters before the equipment is disconnected from the power supply and the cutters have reached a

standstill.

Do not lose these safety instructions

Danger!

Sound and vibration

Lpa sound pressure level: 78.4 dB(A)

Kpa uncertainty: 2.5 dB

Lwa

sound power level: 91.93 dB(A)

Kwa uncertainty: 1.5 dB

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Total vibration values (vector sum of three directions) determined in

accordance with EN 60745.

Vibration emission value ah ≤ 2.5 m/s²

K uncertainty = 1.5 m/s²

The specied vibration value was established in accordance with a

standardized testing method. It may change according to how the electric

equipment is used and may exceed the specied value in exceptional

circumstances.

The specied vibration value can be used to compare the equipment with

other electric power tools.

The specied vibration value can be used for initial assessment of a harmful

effect.

Keep the noise emissions and vibrations to a minimum.

• Only use appliances which are in perfect working order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance off when it is not in use.

• Wear protective gloves.

Caution!

Residual risks

Even if you use this electric power tool in accordance with instructions,

certain residual risks cannot be rules out. The following hazards may

arise in connection with the equipment’s construction and layout:

1. Lung damage if no suitable protective dust mask is used.

2. Damage to hearing if no suitable ear protection is used.

3. Health damage caused by hand-arm vibrations if the equipment is used

over a prolonged period or is not properly guided and maintained.

ADDITIONAL INFORMATION

For EU countries only

Never place any electric power tools in your household refuse.

To comply with European Directive 2012/19/EC concerning old electric and

electronic equipment and its implementation in national laws, old electric

power tools have to be separated from other waste and disposed of in an

environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the manufacturer, the

owner of the electrical equipment must make sure that the equipment is

properly disposed of if p1-he no longer wants to keep the equipment. The old

equipment can be returned to a suitable collection point that will dispose of

the equipment in accordance with the national recycling and waste disposal

regulations. This does not apply to any accessories or aids without electrical

components supplied with the old equipment.

The reprinting or reproduction by any other means, in whole or in part, of

documentation and papers accompanying products is permitted only with the

express consent of the iSC GmbH.

Subject to technical changes.

DECLARATION OF CONFORMITY

DESCRIPTION OF SYMBOLS

SERVICE INFORMATION

Danger! Read Note the instructions for use!

Danger! If the cable is damaged or cut, pull out the

power plug from the mains immediately.

Danger! Never use the equipment in damp locations.

Danger! Rotating tool.

Guaranteed sound p er level: 93 dBow

Caution! Wear safety goggles!

Caution! Danger from catapulted parts; keep a safe distance.

Caution! Wear ear muffs!

Danger! Pull the power plug before carrying out maintenance,

cleaning and repair work.

Liu/Product-ManagementWeichselgartner/General-Manager

explains the following conformity according to EU directives and norms for

the following product

Electric Tiller ETL-7530U (Ozito)

2014/29/EU

2005/32/EC_2009/125/EC

2014/35/EU

2006/28/EC

2014/30/EU

2014/32/EU

2014/53/EC

2014/68/EU

90/396/EC_2009/142/EC

89/686/EC_96/58/EC

2011/65/EU

X 2006/42/EC

Annex IV

Notied Body:

Notied Body No.:

Reg. No.:

2000/14/EC_2005/88/EC

Annex V

X Annex VI

Noise: measured LWA = 91,93 dB (A); guaranteed LWA = 93 dB (A)

P = 0,75 KW; L/Ø = 30 cm

Notied Body: Société Nationale de Certication et dʼHomologation

S.A.R.L. (SNCH) (0499)

2012/46/EU

Emission No.:

Standard references: EN 60335-1; EN 709; EN 62233;

EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3

Landau/Isar, den 11.09.2017

First CE: 17 Archive-File/Record: NAPR017669

Art.-No.: 30.002.09 I.-No.: 11017 R. GehardDocuments registrar:

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar

Cord Restraint & Cord

Clips x 2

Please note that the following parts of this product are subject to normal or

natural wear and that the following parts are therefore also required for use as

consumables.

Category Example

Wear parts* Carbon brushes, tines

Consumables

Missing parts

* Not necessarily included in the scope of delivery!

Spare parts can be ordered from the Special Orders Desk at

your local Bunnings Warehouse or Homebase store.

For further information, or any parts visit

www.ozito-diy.co.uk or contact Ozito Customer Service:

Great Britain: 0151 294 4488

Ireland: 1850 882711

E-mail: info@ozito-diy.co.uk

SPARE PARTS

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to

the online manual.

KNOW YOUR PRODUCT SETUP & PREPARATION

1. BEFORE USE 2. ASSEMBLY 3. STARTING & STOPPING 4. OPERATING THE TILLER

ELECTRIC TILLER

OPERATION

9 10 11

1. Start/Stop Lever

2. Lock-off Button

3. Upper Handle

4. Lower Handle

5. Motor Housing

6. Lower Handle Bracket

7. Fender

8. Tines

9. Upper Handle Bolt x 2

10. Securing Knob x 2

11. Lower Handle Bolt & Nut x 2

1. Slide the upper handle

over the upper ends of the

lower handle. Fit the bolts

through the upper handle

and then through the hole

in the lower handle.

2. Secure in place by

screwing the supplied

securing knobs over the

protruding ends of the

bolts.

1. First, slide the extension

cord restraint onto the

lower handle.

2. Insert the lower handle

to lower handle brackets

and x in place with the

supplied bolts and nuts.

1. To start the tiller, press and

hold the Lock-off Button.

¥ Water the work area prior to commencing tilling operation.

¥ Move the tiller to the work area prior to starting the motor.

¥ Hold the tiller firmly while switching it on. The tines will pull

the tiller forward during operation.

¥ Hold the upper handle securely, walk backwards slowly and

allow the tines to dig into the work area.

¥ For breaking sod or deep tilling, allow the tines to pull the

tiller forward to the end of your arm’s reach, then firmly pull

the tiller back towards you. By repeatedly allowing the tiller to

move forward and then pulling back to you, the tiller will be

most effective.

¥ For better results, move the machine forward as well as

backwards.

¥ If the tiller digs deep enough to stay in one spot, gently rock

the tiller side to side to start the tiller moving forward again.

¥ Lay the power cable on the ground in front of the outlet in

a gure 8. Work away from the outlet or cable and ensure

that the power cable always trails in the hoed soil which will

prevent the hoe blades from travelling over the cable.

Fitting the Lower Handle

Fitting the Upper Handle

WARNING!: ENSURE ENSURE THE TOOL IS

DISCONNECTED FROM THE POWER SUPPLY BEFORE

ASSEMBLY

WARNING!: THE POWER SUPPLY FOR THIS PRODUCT

SHOULD BE PROTECTED BY A RESIDUAL CURRENT

DEVICE RATED AT 30mA OR LESS.

Starting the Tiller

For your safety the Tiller is designed with a safety switch. If the

Start/Stop Lever is squeezed, the tiller will not operate. This

prevents accidental start up of the tiller.

2. Pull the Start/Stop Lever

towards the handle, the

motor will start and the Tines

will begin to rotate, then

release the Lock-off Button.

1. Release the Start/Stop Lever to stop the Tiller.

Stopping the Tiller

Tips

For preparing seed bed, we recommend using one of the tilling

patterns.

Tilling Pattern A - Make two

passes over area to be tilled,

the second at a right angle to

the rst.

Tilling Pattern B - Make two

passes over area to be tilled,

the second overlapping the rst.

WARNING!: KEEP

POWER CORD

AWAY FROM TINES.

¥ To prevent tripping take particular care when moving

backwards and when pulling the tiller.

¥ Always let the tines rotates at top speed; do not work in such

a way as to overload the tiller.

¥ Never pass the tiller over the power cord; make sure it is

always in a safe position behind your back.

¥ When working on inclines always stand diagonally to the

incline in a sturdy, safe.

¥ Keep the underside of the machine clean and remove soil

deposits. Deposits make it more difcult to start the machine

and decrease the working depth.

Transport

CAUTION!: BEFORE TRANSPORTING THE TILLER, SWITCH

OF THE MOTOR.

The tines and machine may be damaged even if you move the

tiller with the motor switched off, e.g. over solid ground. Prevent

the tines from touching the ground by carrying out the tiller by

the lower handle.

Cleaning Tines of Foreign Objects

During operation, a stone or root could become lodged in the

tines, or tall grass or weeds may become wrapped around the

tine shaft.

To clear the tines, switch off the tiller. Unplug the tiller, and

dislodge or remove any obstacles from the tines or tine shaft.

To ease removal of tall grass or weeds that are wrapped around

the tine shaft, remove one or more of the tines from the tine

shaft.

Fault Possible Cause Remedy

Motor does not

start

No Power at power

supply

Check the power

supply and fuses

Excessive working

depth.

Reduce working

depth.

Switch & cord set

assembly defective Arrange the repair

by an electrician or

power tool repairer

Abnormal noise Tines are jammed Disconnect power

and determine

cause

Loose bolts and

nuts

Tighten all

components

Abnormal

vibrations

Tines damaged or

worn

Replace tines

Working depth too

large

Adjust for correct

working depth

Poor scarication

results

Working depth too

small

Adjust for correct

working depth

Worn tines Replace tines

Soil too hard Correct working

depth.

ETL-7530U

Items Supplied

Please check that the article is complete as specified in the scope

of delivery. If parts are missing, please contact our service centre or

the sales outlet where you made your purchase at the latest within 5

working days after purchasing the product and upon presentation of

a valid bill of purchase. Also, refer to the warranty table in the service

information at the end of the operating instructions.

¥ Open the packaging and take out the equipment with care.

¥ Remove the packaging material and any packaging and/or

transportation braces (if available).

¥ Check to see if all items are supplied.

¥ Inspect the equipment and accessories for transport damage.

¥ If possible, please keep the packaging until the end of the guarantee

period.

Danger!

The equipment and packaging material are not toys. Do not let

children play with plastic bags, foils or small parts. There is a

danger of swallowing or suffocating!

Proper Use

The machine is designed for digging soil (for example garden beds). Be

sure to observe the restrictions in the safety instructions.

The operating instructions as supplied by the manufacturer must be

kept and referred to in order to ensure that the machine is properly

used and maintained. The instructions contain valuable information on

operating, maintenance and servicing conditions.

For safety reasons, the machine may not be used as a drive unit for

other work tools or tool sets of any kind.

The equipment is to be used only for its prescribed purpose. Any other

use is deemed to be a case of misuse. The user / operator and not

the manufacturer will be liable for any damage or injuries of any kind

caused as a result of this.

Please note that our equipment has not been designed for use in

commercial, trade or industrial applications. Our warranty will be voided

if the machine is used in commercial, trade or industrial businesses or

for equivalent purposes.

5. TROUBLESHOOTING

1. Remove the two screws

and the side cover from the

safety switch.

Fitting the Safety Switch

2. Fit the safety switch to the

upper handle as shown.

3. Ret the side cover and

secure with the screws

removed in step 1.

Securing the Power Cord

1. Secure the power cord from

the switch housing to the

handle using the two cord

clips as shown.

NOTE: Ensure the cord follows

the handle smoothly from the

switch to the body of the tiller.

WARNING!: THE TILLER BLADES WILL CONTINUE TO

ROTATE FOR A FEW SECONDS AFTER THE MOTOR

IS SWITCHED OFF . NEVER ATTEMPT TO MANUALLY

STOP THEM. IN THE EVENT THAT THE ROTATING TILLER

BLADE STRIKES AN OBJECT, IMMEDIATELY SWITCH OFF THE

MACHINE AND WAIT FOR THE TILLER BLADES TO COME TO

A COMPLETE STOP. THEN INSPECT THE CONDITION OF THE

BLADES.

Overload Protection

The tiller has an internal cut off switch which will stop the

operation of the motor temporarily if too high in temperature.

This cut off switch will suddenly stop the motor from operating

should the motor become too hot during the operation of the

tiller.

First disconnect the tiller from the power supply and inspect

blade for any obstructions.

A wait of 10 minutes in cooling time, or longer depending on

ambient temperature and the operation being performed,

before switching On the tiller and resuming normal operation.

CAUTION!: BE PARTICULARLY CAREFUL WHEN YOU PULL

THE MACHINE TOWARD YOURSELF.

Specyfikacje produktu

Marka:	Ozito
Kategoria:	Niesklasyfikowane
Model:	ETL-7530U

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ozito ETL-7530U, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Ozito

Ozito PXLEK-1840 Instrukcja

5 Stycznia 2025

Ozito PXBGSS-1815 Instrukcja

10 Grudnia 2024

Ozito PXBSPS-180 Instrukcja

6 Października 2024

Ozito SSH-240 Instrukcja

6 Października 2024

Ozito PXPPS-1820 Instrukcja

4 Października 2024

Ozito PXNGS-218 Instrukcja

4 Października 2024

Ozito PSR-5732U Instrukcja

3 Października 2024

Ozito PXCLMLTC-418U Instrukcja

3 Października 2024

Ozito PXDDK-301U Instrukcja

3 Października 2024

Ozito WPHGK-2000U Instrukcja

3 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

GBC ThermaBind T500Pro Instrukcja

15 Stycznia 2025

Da-Lite Parallax 29850 Instrukcja

15 Stycznia 2025

Crivit IAN 290909 Instrukcja

15 Stycznia 2025

Tripp Lite SmartRack SRW12US Instrukcja

15 Stycznia 2025

Powerfix IAN 280221 Instrukcja

15 Stycznia 2025

AGM Rattler TC35-640 Instrukcja

15 Stycznia 2025

AGM Wolf-7 Pro Instrukcja

15 Stycznia 2025

AGM Anaconda TC50-640 Instrukcja

15 Stycznia 2025

AGM Secutor Pro TS50-640 Instrukcja

15 Stycznia 2025

Microchip AT91SAM9M11 Instrukcja

15 Stycznia 2025