Instrukcja obsługi Onkyo HTP-548

Onkyo Zestaw kina domowego HTP-548

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Onkyo HTP-548 (1 stron) w kategorii Zestaw kina domowego. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/1

Enjoying Home Cinema

The Home Cinema means that you can enjoy surround sound with a real sense of movement in your own home — just like being in

a movie theater or concert hall.

Connecting the Speakers

Corner

position

1/3 of wall

position

Center speaker

(SKC-548/SKC-548C)

Position it close to your TV (preferably

on top) facing forward at about ear

level, or at the same height as the

front left and right speakers.

Front left and right speakers (SKF-548)

They should be positioned facing the listener at about ear level,

and equally spaced from the TV. Angle them inward slightly so

as to create a triangle, with the listener at the apex.

Surround left and right speakers (SKR-548)

Position them at the sides of the listener, or

slightly behind, about 60 to 100 cm (2 to 3 feet)

above ear level. Ideally they should be equally

spaced from the listener.

Subwoofer (SKW-538)

The subwoofer handles the bass sounds of the LFE (Low-Frequency Effects) chan-

nel and bass from the satellite speakers when a crossover is specified. The volume

and quality of the bass output from your subwoofer will depend on its position, the

shape of your listening room, and your listening position. In general, a good bass

sound can be obtained by installing the subwoofer in a front corner, or at one-third

the way along the front wall, as shown.

Red White

Blue

Green

Front right

speaker

Center speaker

Gray

Front left

speaker

Surround right

speaker

Surround left

speaker

Speaker Connection

Precautions

Read the following before connecting your

speakers:

• Turn off your receiver before making any

connections.

• Pay close attention to speaker

wiring polarity. Connect posi-

tive (+) terminals to only pos-

itive (+) terminals, and

negative (–) terminals to only negative (–)

terminals. If the speakers are wired incor-

rectly, the sound will be out of phase and

will sound unnatural.

• Be careful not to short the positive and

negative wires. Doing so may damage

your amp.

Powered

subwoofer

*Using the supplied RCA cable,

connect the subwoofer’s LINE

INPUT to your AV receiver’s

SUBWOOFER PRE OUT jack.

Specifications

■Powered Subwoofer (SKW-538)

■Front Speakers (SKF-548)

■Center Speaker

■Surround Speakers (SKR-548)

Specifications and appearance are subject to change without

prior notice.

Note

For non-magnetic shielded speakers:

Try moving the speakers away from your TV or monitor. If discoloration should occur, turn off your TV or monitor, wait 15 to 30

minutes, and then turn it back on again. This normally activates the degaussing function, which neutralizes the magnetic field,

thereby removing any discoloration effects.

Type Bass-reflex

Input sensitivity/impedance 410 mV / 20 kΩ

Rated output Power (IEC) 80 watts minimum continuous power,

4 ohms, driven at 100 Hz with a

maximum total harmonic distortion of

1 %

Frequency response 27 Hz to 150 Hz

Cabinet capacity 24 L

Dimensions (W × H D)×211 mm × 425 mm × 391 mm

(incl. projection)

Weight 8.1 kg

Drivers unit 16 cm Cone × 1

Power supply (European) AC 230V, 50 Hz

(Asian) AC 220 - 240V, 50/60 Hz

Power consumption (European) 90 W

(Asian) 105 W

Other Auto Standby function

Non-magnetic shielding

Type Full Range Bass-reflex

Impedance 6 Ω

Maximum input power 120 W

Sensitivity 82 dB/W/m

Frequency response 80 Hz to 20 kHz

Cabinet capacity 1.0 L

Dimensions (W × H D)×101 mm × 161 mm × 115 mm

(incl. grille and projection)

Weight 0.8 kg

Drivers unit 8 cm Cone × 1

Terminal Spring type color coded

Keyhole slot Available

Grille Fixed

Other Magnetic shielding

Type (SKC-548) Full Range Bass-reflex

(SKC-548C) Full Range Closed Box

Impedance 6 Ω

Maximum input power 120 W

Sensitivity (SKC-548) 82 dB/W/m

(SKC-548C) 84 dB/W/m

Frequency response 80 Hz to 20 kHz

Cabinet capacity 1.4 L

Dimensions (W × × × × H D) 230 mm 103 mm 115 mm

(incl. grille and projection)

Weight (SKC-548) 0.9 kg

(SKC-548C) 1.3 kg

Drivers unit (SKC-548) 8 cm Cone × 1

(SKC-548C) 8 cm Cone × 2

Terminal Spring type color coded

Keyhole slot Available

Grille Fixed

Other Magnetic shielding

Type Full Range Bass-reflex

Impedance 6 Ω

Maximum input power 120 W

Sensitivity 80 dB/W/m

Frequency response 80 Hz to 20 kHz

Cabinet capacity 1.0 L

Dimensions (W × × × × H D) 101 mm 161 mm 115 mm

(incl. grille and projection)

Weight 0.7 kg

Drivers unit 8 cmCone × 1

Terminal Spring type color coded

Keyhole slot Available

Grille Fixed

Other Non-magnetic shielding

■Rear

Note

•

The Auto Standby function turns the subwoofer on when the input signal exceeds a certain

level. If the Auto Standby function does not work reliably, try slightly increasing or decreas-

ing the subwoofer output level on your receiver.

• If the Standby/On indicator lights (both red and blue LEDs) several seconds or minutes

after the sound output stopped, this means that the amp protection circuit has been acti-

vated. In this case, set the OUTPUT LEVEL control to the center position, and discon-

nect the power cord from the AC outlet. Wait at least 10 seconds, and then reconnect the

power cord. If that doesn’t solve the issue, contact your Onkyo dealer.

Setting the Subwoofer Level

To set the level of the subwoofer, use the OUTPUT LEVEL con-

trol. Set it so that bass sounds are evenly balanced with the treble

sounds from the other speakers. Because our ears are less sensitive

to very low bass sounds, there’s a temptation to set the level of the

subwoofer too high. As a rule of thumb, set the subwoofer level to

what you think is the optimal level, and then back it off slightly.

Using the Floor Pads for Subwoofer

If the subwoofer is placed on a hard floor

(wood, vinyl, tile, etc.) and playback is very

loud, the subwoofer’s feet may damage the

flooring. To prevent this, place the supplied

pads underneath the subwoofer’s feet. The pads

also provide a stable base for the subwoofer.

Subwoofer (SKW-538)

Subwoofer

RCA cable 3.0 m

(10 ft.)

4 floor pads*

POWER switch

Press this switch to the ON position to turn on the

power. Press it to the OFF position to turn off the

power.

OUTPUT LEVEL control

This control is used to adjust the volume of the sub-

woofer.

LINE INPUT

This RCA input should be connected to the

subwoofer pre out on your AV receiver with supplied

RCA cable.

STANDBY/ON indicator

Red: Subwoofer in standby mode

Blue: Subwoofer on

With the Auto Standby function, the SKW-538 auto-

matically turns on when an input signal is detected

in Standby mode. When there’s no input signal for a

while, the SKW-538 automatically enters Standby

mode.

Pad

5.1ch Home Cinema Package HTP-548

Y1012-1

* 2 9 4 0 0 6 3 2 *

SN 29400632

Wall Mounting

Using the Rubber Stoppers for a More Stable Platform

Front speaker (SKF-548) Center speaker

(SKC-548/

SKC-548C) Surround speaker (SKR-548)

Front speakers

Speaker cables 3.5 m

(11 ft.) Center speaker

SKC-548 (European)

SKC-548C (Asian)

Speaker cable 3.0 m

(10 ft.)

Surround speakers

Speaker cables 8.0 m

(26 ft.)

*Configuration of the rubber stoppers may be different from the

figure, such as being 2 sheets instead of 1 sheet, but the total

number will be same.

12 thick rubber stoppers*16 thin rubber stoppers*

Caution

• The front grilles are not designed to be removed so do

not attempt to remove them forcibly, as this will dam-

age them.

To mount the front/surround speakers vertically, use the

keyhole slot shown to hang each speaker on a screw

that’s securely screwed into the wall.

To mount the center speaker horizontally, use the two

keyhole slots shown to hang the speaker on two screws

that are securely screwed into the wall.

Caution

• A mounting screw’s ability to sup-

port a speaker depends on how well

it’s anchored to the wall. If you have

hollow walls, screw each mounting

screw into a stud. If there are no

studs, or the walls are solid, use suit-

able wall anchors. Use screws with a

head diameter of 9 mm (5/16") or less and a shank

diameter of 4 mm (1/8") or less. With hollow walls,

use a cable/pipe detector to check for any power cables

or water pipes before making any holes.

• Leave a gap of between 5 mm (3/16") and 10 mm

(7/16") between the wall and the base of the screw

head, as shown. (We recommend that you consult a

home installation professional.)

We recommend using the supplied rubber stoppers to

achieve the best possible sound from your speakers. The

rubber stoppers prevent the speakers from moving, pro-

viding a more stable platform. Use thick stoppers for the

center speaker, and thin stoppers for the other speakers.

(White) (Red)

(Green)

(Blue) (Gray)

Speaker terminals

Keyhole slot

SKF-548

SKR-548

Speaker terminals

Keyhole slots

SKC-548/

SKC-548C

Keyhole slot for

wall mounting

Thick rubber

stoppers

Keyhole slots for wall mounting

183 mm (7-3/16")

Thick rubber

stoppers

Wall

5 to 10 mm

(3/16" to 7/16")

Thin rubber stoppers

Bottom of the

SKR-548

Bottom of the

SKF-548

Bottom of the

SKC-548/SKC-548C

50 mm

(1-15/16")

12 mm (1/2")

Thick rubber stoppers

Specyfikacje produktu

Marka:	Onkyo
Kategoria:	Zestaw kina domowego
Model:	HTP-548

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Onkyo HTP-548, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Zestaw kina domowego Onkyo

Onkyo HT-S9800 Instrukcja

13 Października 2024

Onkyo TX-SR3100 Instrukcja

29 Września 2024

Onkyo HT-S7700 Instrukcja

7 Września 2024

Onkyo HT-S5700 Instrukcja

6 Września 2024

Onkyo L-MS30 Instrukcja

4 Września 2024

Onkyo SKS-HT728 Instrukcja

1 Września 2024

Onkyo HTP-348 Instrukcja

29 Sierpnia 2024

Onkyo HTP-548 Instrukcja

19 Sierpnia 2024

Onkyo HT-S5910 Instrukcja

13 Sierpnia 2024

Onkyo HT-S5400 Instrukcja

4 Lipca 2024

Instrukcje Zestaw kina domowego

Najnowsze instrukcje dla Zestaw kina domowego

Sony SA-PSD5 Instrukcja

14 Października 2024

LG MAI0702 Instrukcja

9 Października 2024

LG LH-TK3605Q Instrukcja

9 Października 2024

LG XH-TK5022Q Instrukcja

8 Października 2024

LG MAI0522 Instrukcja

8 Października 2024

LG MAI0552 Instrukcja

8 Października 2024

LG LH-T2665 Instrukcja

8 Października 2024

Samsung HT-KD800 Instrukcja

8 Października 2024

Samsung HT-DS1870 Instrukcja

8 Października 2024

Bose Solo Soundbar 2 Instrukcja

8 Października 2024