Instrukcja obsługi Octane Fitness XR6000S

Octane Fitness Rower treningowy XR6000S

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Octane Fitness XR6000S (2 stron) w kategorii Rower treningowy. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2



B-6 (2)

103743-001

Box Contents

Install Seat

Hardware Pack

Latin America/Asian Pacific

001-763-757-2662

Europe/Middle East/Africa

31-10-2662412

Questions?

octanefitness.com

113201-001 REV E Page 1/2

USA & Canada

888-OCTANE4

Base

(xR6000 shown)

Tools Required:

#2 Phillips screwdriver

 17mm wrench



Moving Handlebars

(Right and Left)

112508-001

112509-001

Information Packet

113201-001 Assembly

107786-001 Safety Instructions



B-1 (1) 

B-2 (1)



B-9 (4)



B-4 (2) 

B-5 (4)

105717-001

8022048

Install

Mast

Install Console

 Separate console back from console front; set console back aside (not shown).

 Connect the C-SAFE cable from the mast cover to the console (cable not

shown). Note: If you are installing a 900 MHz accessory, remove and

discard the C-SAFE cable.

 Connect heart rate cable attached to heart rate board on console back

to heart rate cable from mast (black, 6-pin connector).

 Make additional cable connections from mast to back of console:

Standard Console:



power,



handlebars,



base,



LAN,



ground

Smart Console:



power,



handlebars,



base,



LAN

(leave ground unconnected)

 Routing loose cables to user front side of mast brackets, attach console front to

top of mast with C-1 (quantity 4); tighten using Phillips #2 screwdriver. Remove

screw securing mast cover to mast; retain screw. (If C-SAFE cable is in use,

let mast cover hang from cable.)

 For Smart console only: Install power switch; connect cable and power.

a. Remove rubber plug from mast cover (not shown).

b. Route two-connector end of switch cable (pre-connected to console) through the

opening where plug was removed. Attach connectors to tabs on switch

(either connector can go on either tab).

c. Press switch fully into opening of mast cover; let mast cover hang

from cables.

d. Connect power cord and power supply. Plug into base of unit

and wall socket to verify power to console. Unplug from wall socket before

continuing to step D.

Standard Console Box Contents

5mm hex wrench (provided)



Tools Required:

#2 Phillips Screwdriver



Information Packet (attached to console)

110601-001 Notice to Installers

111289-001 xR6000 Console Guide & Setup

Instructions–Standard Console

104198-001 Warranty

101315-001 Registration Card









Standard Console

(Front and Back)

8020168

Tools Required:

#2 Phillips Screwdriver



110601-001 Notice to Installers

111768-001 Console Guide & Set-up Instructions–

Smart Console

104198-001 Warranty

101315-001 Registration Card

Information Packet (attached to console)

Smart Console

(Front and Back)

8019479

Standard

Console

Smart

Console

Console to Base

(white, 14-pin)

Handlebar Control

(white, 7-pin) Console Ground

(metal; green wire from mast)

Reserved

(unused)

Audio for

Accessories

(unused)

Power

(white, 4-pin)

Power for

Accessories

(unused)

Reserved for

Software Field Update

(black)

LAN

(RS-232)









C-SAFE

(Connect from mast

cover in Step



)



Standard Console

Power Switch

111032-001

Power Supply

112584-001

#2 Phillips

C-1 (10)

100780-001

Hardware Pack

110622-001

#2 Phillips

C-1 (10)

100780-001

Hardware Pack

110622-001

F-2

(may be boxed separately)

Power Cord

107658-001

(may be boxed separately)



Smart Console

Handlebar Control

(white, 7-pin)



Console to Base

(white, 14-pin)



Power

(white, 4-pin)

LAN

(RS-232)

(on Android board

underneath)



Power for

Accessories

(unused)

C-SAFE

(Connect from mast

cover in Step )





Arm Pivot Cover–Large

(Right and Left)

113185-001

Hardware Pack

112844-001

6mm

5mm



B-6 (2)

112734-001



B-11 (4)

112223-001



B-13 (2)



B-12 (2)



B-10 (2)

101277-001

Console Mast

112738-001



Foot Rest/Accessory Tray

112824-001

Foot Pedals

(Right and Left)

116661-001

111660-001



Seat Back

Enter

PAUSE

CLEAR

Time Calories Distance Speed

HR% HR Level

Challenging intervals isolating legs for power and toning

Higher resistance intervals isolating arms, shoulders and chest

A built-in personal trainer to motivate you with intense intervals

HIIT BOOSTERS

Program

Workout

Narrow Grip Wide Grip

Reverse

Legs Only Resistance

Push Arms Pull Arms

Fast

PRESS TO ACTIVATE

Quick Start

Level

OCTANE

FAVORITES

MMA

30:30

(Install back cover

and mast cover, C-SAFE

cable not shown)

6mm hex wrench (provided)



6-c

F-2

(Install back cover

and mast cover, C-SAFE

cable and power switch

cable not shown)

F-2





F-2



6-d

Flat head screwdriver



Assembly Instructions

(not shown)

112832-001

113183-001

Arm Pivot Cover–Small

(Right and Left)

113182-001 113184-001

Smart Console Box Contents

 Use 6mm hex wrench to remove bolt and

washer from right side of seat back axle;

slide axle out user left side.

 Position seat back; insert axle from left side through seat back

bracket, aligning flat sides of axle and hole. Align washer and

bolt with axle; tighten with 6mm hex wrench to 19 ft-lb.

 Insert spacer B-2 (quantity 1) through hole in damper. Tilt seat

and align damper/spacer in seat bracket. Insert screw B-1

(quantity 1) through bracket and damper/spacer;

tighten with 5mm hex wrench to 7 ft-lb.

 Test seat height and tilt adjustments to verify function of locking

mechanisms (not shown). (On xR6000s, also test swivel mechanism.)

Remove all loose parts from packaging; use handle to

lift rear of base and gently roll unit off

shipping pallet.

112736-001 113194-001

109989-001 104757-001 103743-001

8008949

 6mm Hex (1)

103083-001

 5mm Hex (1)

 Use #2 Phillips screwdriver to remove two screws

securing front and rear top shrouds and mast boot. Set

screws, shrouds, and mast boot aside (not shown).

 Remove twist tie securing cable bundle; tip mast

upside down and route cables through hole in

bottom of mast to top of mast.

 Slide mast over screws on base; insert screw B-3

(quantity 2) into holes in front of mast plate, tighten

with 6mm hex wrench.

 Insert screw B-3 (quantity 2) into holes in top of

mast plate. Use 6mm hex wrench to tighten

all 6 screws to 30 ft-lb.

 Align bottom of front top shroud with base, then tip up

into position. Position rear top shroud and mast boot,

then secure both top shroud pieces using #2 Phillips

screwdriver and two screws removed in step 1.



B-3 (4)

101295-001

6mm

100780-001

#2 Phillips



B-8(4)

13mm

6mm

Rubber mallet

(optional)













Side Step (2)

113208-001

(xR6000s only)



cables

through

here









13mm wrench





Read and understand the “Product Safety Information” manual

before assembly.



B-7 (2)

103393-001

 Complete Console Setup according to instructions found in

the Console Guide

and Setup Instructions (Part Number 111289-001 – Standard Console or

Part Number 111768-001 – Smart Console).

 Use a #2 Phillips screwdriver to attach back cover to console with C-1

(quantity 6); tighten. Reattach mast cover to mast with screw removed in

step C-5, taking care to tuck cables out of the way before securing to mast.

(Shown in Section C illustration).

 Level machine; adjust and lock levelers using 17mm wrench.

Make sure nut is tight.

Complete Setup &

Level Machine

If you have the optional Personal Viewing System (PVS) accessory, refer to Personal Viewing System (PVS) Assembly Instructions

located in the box with your PVS accessory, then return to these instructions to complete final assembly.

If you have the optional 900 MHz accessory, refer to 900 MHz Assembly Instructions located in the box with your 900 MHz accessory,

then return to these instructions to complete final assembly.

STOP

Connect Battery & Attach Moving Handlebars

 With upper pedal links positioned on front side of mast post, attach foot rest bracket to

mast with screw B-9 (quantity 4); tighten all 4 screws with 5mm hex wrench until tight.

To install foot pedal:

 Place wave washer B-10 (quantity 1) on pedal crank axle, then press lower end of foot pedal

onto pedal crank axle. (Use a rubber mallet to assist if needed.)

 Place washer B-5 onto screw B-11 (quantity 1 each). Insert B-11/B-5 assembly into lower

hub and into pedal crank axle; tighten with 6mm hex wrench to 19 ft-lb.

Press cap B-12 into place in lower foot pedal hub.

 Place cap B-13 onto screw B-11 (quantity 1 each). Insert B-11/B-13 assembly through upper

pedal link into upper foot pedal hub; tighten with 6mm hex wrench to 19 ft-lb.

Repeat steps 2-4 for second foot pedal.

 For xR6000s Only: Place side step next to one side of the unit with back of side step aligned

with back of foot platform. Carefully tip unit away from you and push side step under rail of

unit. Lower unit onto side step channel. Repeat for second side step.

Assembly Instructions

Latin America/Asian Pacific

001-763-757-2662

Europe/Middle East/Africa

31-10-2662412

Questions?

octanefitness.com

113201-001 REV E Page 2/2

USA & Canada

888-OCTANE4

Attach Foot

Pedals & Foot Rest

 Use #2 Phillips screwdriver to remove 4 screws securing battery access panel.

Use flat screwdriver at the side corner seams to gently unsnap bottom of panel;

remove from unit and set aside with screws.

 Use #2 Phillips screwdriver to remove 1 screw securing each crank arm cover; turn

each cover counter-clockwise to remove and set aside with screws.

 Connect cable on battery to cable in base (if you have not already done so during

installation of PVS or 900MHz accessory). Connect power cord to wall socket.

To install moving handlebar:

 Place washer B-5 on bolt B-4 (quantity 1 each); attach moving handlebar

at hub with B-4/B-5 assembly and tighten with 13mm wrench to 19 ft-lb.

 Position pedal crank axle at top-most position. Insert arm link of moving handlebar

into arm link bracket, aligned with hole #1 on bracket. From the outside toward the

center of the unit, insert screw B-6 (quantity 1) into arm link bracket and through arm

link and nut B-7; tighten with 13mm wrench to 17 ft-lb. For a longer reach, use hole #2 in

the arm link bracket. You must use the same hole (#1 or #2) on both handlebars.

 Position large arm pivot cover around handlebar shaft and slide down to hub,

inserting posts on pivot cover into square holes in hub. Use #2 Phillips screwdriver

to secure large arm pivot cover to hub with B-8 (quantity 1). Press tabs of small arm

pivot cover into slots in large arm pivot cover. Use #2 Phillips screwdriver to secure

small arm pivot cover with B-8 (quantity 1).

Complete steps 4-6 for second moving handlebar.

 Verify that you have properly connected the battery (per step 1). Then, move

handlebars back and forth to check console power (not shown).

For standard console: Verify console powers up and stays lit for more than 5

seconds. For smart console: Press power switch to start console and verify

xR6000 landing screen displays.

 Position each crank arm cover, turning it clockwise to lock into place, then secure

using #2 Phillips screwdriver and screws removed in step 2.

 Position bottom of battery access panel and snap into place, then press top

of panel into place. Use #2 Phillips screwdriver and secure with

4 screws removed in step 1.













cables

not

shown







Install Side Steps

(xR6000s only)



















(Console and mast

not shown)

snap

apart

here



Specyfikacje produktu

Marka:	Octane Fitness
Kategoria:	Rower treningowy
Model:	XR6000S

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Octane Fitness XR6000S, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Rower treningowy Octane Fitness

Octane Fitness Q35C Instrukcja

27 Września 2024

Octane Fitness Q35X Instrukcja

27 Września 2024

Octane Fitness XR6000 Instrukcja

27 Września 2024

Octane Fitness ZR8000 - Standard Console Instrukcja

27 Września 2024

Octane Fitness ZR8000 - Smart Console Instrukcja

27 Września 2024

Octane Fitness XT - Smart Console 2016 Instrukcja

27 Września 2024

Octane Fitness Q37Xi Instrukcja

27 Września 2024

Octane Fitness Q47Xi Instrukcja

27 Września 2024

Octane Fitness Q47C Instrukcja

27 Września 2024

Octane Fitness XT4700 Instrukcja

27 Września 2024

Instrukcje Rower treningowy

Najnowsze instrukcje dla Rower treningowy

Body Sculpture BMG-4700C Instrukcja

15 Października 2024

Tacx Bushido Smart T2780 Instrukcja

10 Października 2024

Skandika Foldaway X-2000 Instrukcja

9 Października 2024

Christopeit ET 3.1 Instrukcja

9 Października 2024

Christopeit HT 2.2 Instrukcja

8 Października 2024

Assault Bike Elite Instrukcja

8 Października 2024

Assault Bike Pro X Instrukcja

8 Października 2024

Christopeit S-Bike Instrukcja

7 Października 2024

Body Sculpture BE-6115 Instrukcja

7 Października 2024

SportsArt TR12 Instrukcja

6 Października 2024