Instrukcja obsługi NuTone CP2OHAB

NuTone dzwonek do drzwi CP2OHAB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla NuTone CP2OHAB (4 stron) w kategorii dzwonek do drzwi. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

D) Doors vary in thickness depending on the manufacturer. At

the edge of the door, measure the thickness of the door. Then,

determine the distance to the center to the edge of the door

(half the thickness of the door). Using the awl (or nail), mark

a point on the edge of the door where the centerline pencil

mark (from Step 1C) and the center of the edge of the door

meet (half the thickness), see .Figure #3

Step 2

Drill the Door

A) Using the 2-1/8” hole saw, drill the cross bore hole centered

on the mark made on the face of the door from Step 1B. See

Figure #3 Important:. To avoid splintering or marring the

door, drill from one side of the door until the pilot bit comes

through the door. Then nish drilling from the other side of

the door, using the hole made by the pilot bit as your guide

until the cross bore hole is complete.

B) Using the 1” bit, drill the edge bore hole centered on the mark

made on the edge of the door where the centerline and center

thickness met from Step 1D, see Figure #3 Important:.

Make sure that you drill a full 3-1/2” deep, to accommodate

the overall length of the 2-3/8” latch. If you are using a 2-3/4”

backset latch, then the overall depth must be at least 3-3/4”.

v

v

v

v

&ORv"ACKSET

&ORv"ACKSET

#ROSS"ORE

(OLEv

$IAMETER

-ARKFROM

3TEP"

%DGE"ORE

(OLEv

$IAMETER

-ARKFROM

3TEP$

$OOR4HICKNESS

&ACEPLATE

-ORTISE

!REA

#ENTERLINE

-ARKFROM

3TEP#

-INIMUM

 TOCENTERv

LINEOFDOOR

KNOBCROSS

BOREHOLE

Door Hardware

Installation Instructions

Rosette Passage and Privacy

Carefully unpackage all components and place them within easy

reach. Find on Page 4 of these instructions for a listing Figure #1

and drawing of each component. Detach and place Figure #1

beside the components for easy reference. Check your door to see

if it has been prepped (pre-drilled) for installing a lock. If your

door has already been prepped for installation, start at Step 4. If

your door has not been prepped for installation, you will need a

#2 Phillips screwdriver, a drill, a 2-1/8” hole saw, a 7/64” drill bit,

a 1” drill bit, chisel, pencil, tape and an awl (or nail).

Step 1

Mark the Door

A) Locate the Door Preparation Template that is included with

the instructions. Fold the template along the “edge-of-door”

line. : Before positioning the template, make sure Important

that you are aligning it on the . non-hinged edge of the door

Carefully position the template so that the narrow portion

of the template wraps around the edge of the door, and the

large portion of the template remains on the face of the door,

see . The centerline indicates the center of where Figure #2

the knob or lever will be located. Slide the template up or

down on your door so that the horizontal centerline is located

at a height that is both comfortable to use and attractive in

appearance. Typically this will be approximately 36”-38”

from the oor, see Figure #2. Once you have chosen the

height, tape the template to the door.

B) The backset is the distance from the edge of the door to

the center of the rosette. Standard backsets are 2-3/8” and

2-3/4”. Determine the backset of your latch (Part #5), by

checking the marking on the latch itself (if marked, it will say

2-3/8” or 2-3/4”). If the latch is not marked, measure the latch

between points A and B to determine the backset, as shown

in Figure #2. Once you know your backset, nd the point on

the template where the centerline crosses the vertical line that

corresponds with the correct backset. Using the awl (or nail)

mark this point, making sure that it is marked well enough to

see on the door once the template is removed.

C) Follow the centerline around the edge of the door and using

a pencil, extend the centerline onto the edge of the door. The

mark should be parallel to the oor. Once this mark is made,

you may remove the template from the door. Page 1 - PK143

For

Assistance

Call:

1-800-522-7336

8 am - 5 pm, Monday - Friday, MST

(A) (B)

Template

Edge

Door

Face of Door

Centerline

Latch

Backset

Measurement

2-3/8” or 2-3/4”

Figure #2

Figure #3

Anti-

Rotation

Block

Latch

Tongue

Star Shaped

Hub

Inside Face of Door

Threaded

Privacy Pin

Hole

C) Determine which direction the door will swing when it is

being opened. Rotate the latch tongue so that the at edge of

the tongue faces toward the direction the door swings when

being opened (and the round edge towards the doorjamb).

Once oriented correctly, install the faceplate (Part #7) over the

latch tongue (Part #5a), locking the latch tongue orientation.

Fasten in place using two 1” wood screws (Part #8) Hint:

Coating the screw threads with a small amount of soap (liquid

or bar soap) will make installation easier.

Step 5

Install the Trim

A) Using for reference, gather together the trim half A Figure #1

(Part #1), trim half B (Part #2), 1-1/2″ rosette machine screws

(Part #3), and Phillips screwdriver.

B) Find trim half A (Part #1). Place trim half A on the outside of

the door, such that the spindle is inserted into the star-shaped

hub of the latch and the screw bosses are nested in the top and

bottom slots in the anti-rotation block, see . Figure #5 Lever

designs only: If installing a lever, see for correct Figure #6

orientation of lever on the door. If your lever is oriented

incorrectly, move it to the other side of the door so it matches

the correct orientation in , before proceeding with Figure #6

installation. Make sure that the Privacy function only:

privacy hole in the rose is oriented so that it is closest to the

edge of the door where the latch tongue sticks out.

Correct Lever Orientation

(Lever Rotates Downward)

Incorrect Lever Orientation

To correct, remove from door and

mount on opposite door face

Door

Edge

Step 3

Mortise for the Faceplate

A) Using Figure #1 for reference, nd the faceplate (Part

#7). On the edge of the door, center the faceplate over the

newly drilled edge bore hole, so that the D-shaped hole in

the faceplate is centered over the 1” edge bore hole. Align

it so that the edges are parallel to the edges of the door and

roughly centered side-to-side. Mark around the faceplate with

a pencil and remove from door.

B) Using the chisel, score the outline of the faceplate. Next,

chisel away the material within the outline to a depth of 1/8”.

When you are done, you should be able to insert the latch

(part #5), place the faceplate over the latch tongue (Part #5a),

and have the faceplate be ush with the edge of the door.

C) Again, using the faceplate as a template and the awl as a

marking tool, mark for the two screws holes that will hold the

faceplate on the door. Remove the faceplate from the door to

avoid marring the nish. Then, drill the two screw holes using

a 7/64” drill bit. Make sure the holes are drilled at least 1”

deep. Having too small or too shallow of a hole can cause the

screws to shear off.

Installing Your Lock

Step 4

Install the Latch

A) Once your door is prepped for installation, you will need a #2

Phillips screwdriver for the installation of your latch.

B) Locate the latch (Part #5) and the anti-rotation block (Part

#4). Insert the anti-rotation block in the cross bore hole so

that the arrow on the block is pointing toward the edge of the

door. Install the latch in the edge bore hole, making sure that

it is correctly inserted through the anti-rotation block. When

installed correctly, the star-shaped hub in the latch should be

centered in the hole of the anti-rotation block, see Figure #4.

Privacy function only: The privacy latch must be inserted

into the door so that the locking mechanism (threaded privacy

pin hole - Part #5b) is facing the inside of the door, see

Figure #1.

Page 2 - PK143

Figure #4

Spindle

Screw

Bosses

Figure #5

Figure #6

C) Hold trim half A on the door. Place trim half B (Part #2) on

the other side of the door, such that the spindle is inserted

into the star-shaped hub of the latch and the screw bosses are

nested in the top and bottom slots in the anti-rotation block.

Now hold both trim halves in place with one hand.

Privacy

function only: Make sure that the privacy hole in the rose is

oriented so that it is closest to the edge of the door where the

latch tongue sticks out.

D) Insert the rst 1-1/2” rosette machine screw (Part #3) into

the top hole of trim half B and loosely tighten until the screw

can hold both halves of the trim on the door. Important:

Make sure that the screwdriver is held in a way that it will not

scratch the knob/lever or rosette.

E) Insert the second 1-1/2” rosette machine screw into the lower

hole and tighten until snug. Tighten down both screws until

the rosette is securely attached on the door.

F) On the interior side of the door, Privacy function only:

screw in the privacy pin (Part #9) until snug. Do not over-

tighten. With the door open, test the privacy lock by pushing

the pin in and then trying the knob on the opposite side of the

door to see if it is locked. Then turn the knob on the interior

side of the door and this will unlock the door.

Step 6

Prepare the Doorjamb and Install

the Strike

A) Using for reference, gather together the strike (Part Figure #1

#6), two 1” wood screws (Part #8), a drill, 1” drill bit, awl (or

nail), a 7/64” drill bit, a pencil and a chisel.

B) If you are installing a privacy lock, make sure the latch is

not locked. Rotate the knob or lever to retract the latch and

carefully close the door, making sure that the latch is fully

retracted and does not scratch the doorjamb. Slowly release

the knob/lever and let the latch tongue extend against the

doorjamb.

C) Using the pencil, lightly mark the doorjamb at the level of the

top and bottom of the latch tongue (Part #5a). These need to

be light marks, so that they can be erased later if needed. Turn

the knob/lever again to retract the latch and re-open the door.

Now extend the marks so that they are approximately 1/2”

from the edge of the door jamb where the door stops when it

is closed, See Figure #7.

D) Repeat Step 6B, and verify that the latch tongue is falling

between the two marks.

E) Measure the thickness of the door. Take half of the door

thickness and measure that same distance from the edge of

the doorjamb where the door stops when it is closed. Mark

on the doorjamb this distance halfway between the two lines

from Step 6C, see Figure #7.

F) Using the awl, mark where the point that is halfway

between the two lines made in Step 6C crosses the line

marked in Step 6E.

G) Using a 1” drill bit, drill a hole centered on the mark from

Step 6F. Make sure the hole is at least 5/8” deep. Clean out

any sawdust from the hole.

H) Using the strike (Part #6) as a template, center the strike

over the 1” hole, mark a line around it in pencil and remove

from doorjamb.

I) Using the chisel, score the outline of the strike. Next, chisel

away the material within the outline to a depth of 1/16”.

When you are done, you should be able to place the strike

in the mortised out area and it should be ush with the

doorjamb.

J) Again, using the strike as a template and the awl as a

marking tool, mark the two screws holes that will hold the

strike on the door. Remove the strike from the doorjamb

to avoid marring the nish. Then, drill the two screw holes

using a 7/64” drill bit. Make sure the holes are drilled at

least 1” deep. Having too small or too shallow a hole can

cause the screws to shear off.

K) Fasten the strike in place using two 1” wood screws (Part

#8). Hint: Coating the screw threads with a small amount

of soap (liquid or bar soap) will make installation easier.

Page 3 - PK143

Congratulations! You are now

on your way to enriching your

life with !

Mark from

Step 6F

Chiseled

Area for

Strike

Half of

Door

Thickness

Door Jamb

Stop

Door Jamb

Lines from

Step 6C

Figure #7

Specyfikacje produktu

Marka:	NuTone
Kategoria:	dzwonek do drzwi
Model:	CP2OHAB

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z NuTone CP2OHAB, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje dzwonek do drzwi NuTone

NuTone CP2ALSN Instrukcja

1 Października 2024

NuTone CP2PSAB Instrukcja

11 Września 2024

NuTone CP2CUAB Instrukcja

11 Września 2024

NuTone CP2FSAB Instrukcja

11 Września 2024

NuTone CP2LVSN Instrukcja

11 Września 2024

NuTone CP2AUSN Instrukcja

11 Września 2024

NuTone CP2MISN Instrukcja

11 Września 2024

NuTone CP2OHAB Instrukcja

11 Września 2024

NuTone CP2SCSN Instrukcja

11 Września 2024

NuTone CP2INAB Instrukcja

11 Września 2024

Instrukcje dzwonek do drzwi

Najnowsze instrukcje dla dzwonek do drzwi

Gira 2506 20 Instrukcja

15 Października 2024

Panasonic VL-VM902EX Instrukcja

12 Października 2024

Elro DB260F Instrukcja

10 Października 2024

Eufy Video Doorbell C30 Instrukcja

9 Października 2024

Velleman HAM9011 Instrukcja

9 Października 2024

CATA THALASSA PRO 90 GGR Instrukcja

8 Października 2024

CATA CK 6000 X Instrukcja

8 Października 2024

CATA THALASSA 600 GWH Instrukcja

8 Października 2024

CATA THALASSA PRO 700 GBK Instrukcja

8 Października 2024

CATA THALASSA PRO 800 GBK Instrukcja

8 Października 2024