Instrukcja obsługi Nissan Versa (2007)
Nissan
Automatyczny
Versa (2007)
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Nissan Versa (2007) (49 stron) w kategorii Automatyczny. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/49
MT-1
MANUAL TRANSAXLE
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION MT A
B
MT
Revision: June 2006 2007 Versa
PRECAUTIONS .......................................................... 2
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 2
Precautions .............................................................. 2
PREPARATION ........................................................... 3
Special Service Tools ............................................... 3
Commercial Service Tools ........................................ 4
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING ................................................ 6
NVH Troubleshooting Chart ..................................... 6
DESCRIPTION ............................................................ 7
Cross-Sectional View ............................................... 7
TRIPLE-CONE SYNCHRONIZER ........................ 8
REVERSE GEAR NOISE PREVENTION FUNC-
TION (SYNCHRONIZING METHOD) ................... 8
M/T OIL ....................................................................... 9
Changing M/T Oil ..................................................... 9
DRAINING ............................................................. 9
FILLING ................................................................. 9
Checking M/T Oil ...................................................... 9
OIL LEAKAGE AND OIL LEVEL ........................... 9
SIDE OIL SEAL ........................................................ 10
Removal and Installation ........................................ 10
REMOVAL ........................................................... 10
INSTALLATION ................................................... 10
POSITION SWITCH ...................................................11
Checking .................................................................11
BACK-UP LAMP SWITCH ...................................11
PARK/NEUTRAL POSITION SWITCH ................11
CONTROL LINKAGE ............................................... 12
Components of Control Device and Cable ............. 12
Removal and Installation ........................................ 12
REMOVAL ........................................................... 12
INSTALLATION ................................................... 13
AIR BREATHER HOSE ............................................ 14
Removal and Installation ........................................ 14
COMPONENTS ................................................... 14
REMOVAL ........................................................... 14
INSTALLATION ................................................... 14
TRANSAXLE ASSEMBLY ........................................ 15
Removal and Installation ........................................ 15
COMPONENTS ................................................... 15
REMOVAL ........................................................... 15
INSTALLATION ................................................... 15
Disassembly and Assembly .................................... 17
COMPONENTS ................................................... 17
DISASSEMBLY ................................................... 23
ASSEMBLY ......................................................... 28
INPUT SHAFT AND GEARS .................................... 34
Disassembly and Assembly .................................... 34
GENERAL PRECAUTIONS ................................ 34
DISASSEMBLY ................................................... 34
INSPECTION AFTER DISASSEMBLY ................ 36
ASSEMBLY ......................................................... 37
MAINSHAFT AND GEARS ....................................... 38
Disassembly and Assembly .................................... 38
GENERAL PRECAUTIONS ................................ 38
DISASSEMBLY ................................................... 38
INSPECTION AFTER DISASSEMBLY ................ 39
ASSEMBLY ......................................................... 40
REVERSE IDLER SHAFT AND GEARS .................. 43
Disassembly and Assembly .................................... 43
DISASSEMBLY ................................................... 43
ASSEMBLY ......................................................... 44
FINAL DRIVE ............................................................ 45
Disassembly and Assembly .................................... 45
DISASSEMBLY ................................................... 45
INSPECTION AFTER DISASSEMBLY ................ 46
ASSEMBLY ......................................................... 46
SHIFT CONTROL ..................................................... 48
Inspection ............................................................... 48
SERVICE DATA AND SPECIFICATIONS (SDS) ...... 49
General Specifications ............................................ 49
MT-2
PRECAUTIONS
Revision: June 2006 2007 Versa
PRECAUTIONS PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER” ECS00GLL
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions UCS005LD
●If transaxle assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylinder).
Installed CSC returns to the original position when removing transaxle assembly. Dust on clutch disc slid-
ing parts may damage CSC seal, and may cause clutch fluid leakage.
●Do not reuse transaxle oil.
●Drain, fill and check transaxle oil with the vehicle on level surface.
●During removal or installation, keep inside of transaxle clear of dust or dirt.
●Check for the correct installation orientation prior to removal or disassembly. If matching marks are
required, be certain they do not interfere with the function of the parts they are applied to.
●In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to outside. If
tightening sequence is specified, follow it.
●Be careful not to damage the sliding surfaces and mating surfaces of parts.
PREPARATION
MT-3
D
E
F
G
H
I
J
K
L
M
A
B
MT
Revision: June 2006 2007 Versa
PREPARATION PFP:00002
Special Service Tools UC S00 655
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV381054S0
(J-34286)
Puller
Removing mainshaft front bearing outer race
KV38100200
( — )
Drift
●Installing mainshaft front bearing outer race
●Installing mainshaft rear bearing outer race
●Installing differential side bearing outer race
(clutch housing side)
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.
ST33220000
( — )
Drift
Installing input shaft oil seal
a: 37 mm (1.46 in) dia.
b: 31 mm (1.22 in) dia.
c: 22 mm (0.87 in) dia.
ST33400001
(J-26082)
Drift
Installing differential side bearing outer race
(transaxle case side)
a: 60 mm (2.36 in) dia.
b: 47 mm (1.85 in) dia.
KV38100300
(J-25523)
Drift
Installing differential side oil seal
a: 54 mm (2.13 in) dia.
b: 46 mm (1.81 in) dia.
c: 32 mm (1.26 in) dia.
ST36720030
( — )
Drift
●Installing input shaft rear bearing
●Installing mainshaft front bearing inner race
a: 70 mm (2.76 in) dia.
b: 40 mm (1.57 in) dia.
c: 29 mm (1.14 in) dia.
ZZA0601D
ZZA1143D
ZZA1046D
ZZA0814D
ZZA1046D
ZZA0978D
Specyfikacje produktu
| Marka: | Nissan |
| Kategoria: | Automatyczny |
| Model: | Versa (2007) |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Nissan Versa (2007), zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Automatyczny Nissan
15 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
13 Października 2024
13 Października 2024
8 Października 2024
4 Października 2024
3 Października 2024
18 Września 2024
Instrukcje Automatyczny
- Automatyczny Peugeot
- Automatyczny Citroën
- Automatyczny Fiat
- Automatyczny Honda
- Automatyczny Audi
- Automatyczny Volkswagen
- Automatyczny Saab
- Automatyczny Toyota
- Automatyczny GEM
- Automatyczny Opel
- Automatyczny Kia
- Automatyczny Dacia
- Automatyczny Subaru
- Automatyczny Ford
- Automatyczny Tesla
- Automatyczny Seat
- Automatyczny BMW
- Automatyczny Mini
- Automatyczny Land Rover
- Automatyczny Mazda
- Automatyczny Skoda
- Automatyczny Vauxhall
- Automatyczny Chrysler
- Automatyczny Volvo
- Automatyczny Suzuki
- Automatyczny Genesis
- Automatyczny Hyundai
- Automatyczny VDL
- Automatyczny Mercury
- Automatyczny Smart
- Automatyczny Jeep
- Automatyczny GMC
- Automatyczny Polaris
- Automatyczny Mercedes-Benz
- Automatyczny Lexus
- Automatyczny MG
- Automatyczny Alfa Romeo
- Automatyczny Chevrolet
- Automatyczny Jaguar
- Automatyczny Maserati
- Automatyczny DS
- Automatyczny Renault
- Automatyczny Mitsubishi
- Automatyczny Buick
- Automatyczny RAM
- Automatyczny Rover
- Automatyczny Dodge
- Automatyczny Infiniti
- Automatyczny Lancia
- Automatyczny Tata
- Automatyczny Acura
- Automatyczny ACME
- Automatyczny Saturn
- Automatyczny Cadillac
- Automatyczny Pontiac
- Automatyczny Porsche
- Automatyczny Scion
- Automatyczny Sharper Image
- Automatyczny Abarth
- Automatyczny Lincoln
- Automatyczny Mahindra
- Automatyczny Chery
- Automatyczny Lada
Najnowsze instrukcje dla Automatyczny
15 Października 2024
15 Października 2024
15 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024