Instrukcja obsługi Nissan Sentra (2001)
Nissan
Automatyczny
Sentra (2001)
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Nissan Sentra (2001) (63 stron) w kategorii Automatyczny. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/63
MANUAL TRANSAXLE
SECTION
MT
CONTENTS
PREPARATION ...............................................................2
Special Service Tools ..................................................2
Commercial Service Tools ...........................................4
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING .....................................................6
NVH Troubleshooting Chart.........................................6
DESCRIPTION.................................................................7
Cross-sectional View ...................................................7
DOUBLE-CONE SYNCHRONIZER ..............................8
ON-VEHICLE SERVICE ..................................................9
Replacing Oil Seal.......................................................9
DIFFERENTIAL OIL SEAL ..........................................9
STRIKING ROD OIL SEAL .........................................9
Position Switch Check...............................................10
BACK-UP LAMP SWITCH ........................................10
PNP SWITCH ..........................................................10
Viscous Coupling Check............................................ 11
REMOVAL AND INSTALLATION.................................12
Removal.....................................................................12
Installation..................................................................14
- QG ENGINE -........................................................14
Installation..................................................................15
- SR ENGINE - ........................................................15
OVERHAUL ...................................................................16
Transaxle Gear Control .............................................16
Case Components.....................................................17
Gear Components .....................................................18
Shift Control Components .........................................19
Final Drive Components............................................20
DISASSEMBLY..............................................................21
Transaxle Case..........................................................21
Clutch Housing ..........................................................23
REPAIR FOR COMPONENT PARTS ...........................27
Input Shaft and Gears ...............................................27
DISASSEMBLY........................................................27
INSPECTION...........................................................28
ASSEMBLY .............................................................29
Mainshaft and Gears .................................................32
DISASSEMBLY........................................................32
INSPECTION...........................................................33
ASSEMBLY .............................................................35
Final Drive..................................................................40
PRE-INSPECTION ...................................................40
DISASSEMBLY........................................................41
INSPECTION...........................................................42
ASSEMBLY .............................................................43
Shift Control Components .........................................46
INSPECTION...........................................................46
ASSEMBLY....................................................................47
Clutch Housing ..........................................................47
Transaxle Case..........................................................51
SERVICE DATA AND SPECIFICATIONS (SDS) .........56
General Specifications...............................................56
TRANSAXLE ...........................................................56
FINAL GEAR ...........................................................56
Gear End Play ...........................................................57
Clearance Between Baulk Ring and Gear ................57
3RD, 4TH, 5TH, REVERSE BAULK RING ..................57
1ST AND 2ND BAULK RING ....................................57
Available Snap Rings ................................................57
SNAP RING.............................................................57
Available C-rings........................................................58
4TH INPUT GEAR C-RING .......................................58
5TH INPUT GEAR REAR C-RING .............................58
MAINSHAFT C-RING ...............................................58
Available Adjusting Shims .........................................59
INPUT SHAFT REAR BEARING ADJUSTING
SHIM ......................................................................59
MAINSHAFT ADJUSTING SHIM................................60
MAINSHAFT REAR BEARING ADJUSTING SHIM ......60
Available Thrust Washer............................................61
MAINSHAFT THRUST WASHER...............................61
Available Washers .....................................................61
DIFFERENTIAL SIDE GEAR THRUST WASHER........61
Available Shims - Differential Side Bearing
Preload and Adjusting Shim ......................................62
BEARING PRELOAD ...............................................62
DIFFERENTIAL SIDE BEARING ADJUSTING
SHIMS ....................................................................62
GI
MA
EM
LC
EC
FE
CL
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
Special Service Tools NIMT0001
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name Description
KV38107700
(J39027)
Preload adapter
NT087
Measuring turning torque of final drive assembly
Measuring total turning torque
Measuring clearance between side gear and differ-
ential case with washer
Selecting differential side bearing adjusting shim
[Use with KV38106000 (J34291-B).]
KV38106000
(J34291-B)
Height gauge adapter
(differential side bearing)
NT418
Selecting differential side bearing adjusting shim
[Use with KV38107700 (J39027).]
a: 140 mm (5.51 in)
b: 40 mm (1.57 in)
c: 16 mm (0.63 in) dia.
d: M8 1.25P×
KV32101000
(J25689-A)
Pin punch
NT410
Removing and installing retaining pin
Removing and installing lock pin
Removing selector shaft
Removing welch plug
a: 4 mm (0.16 in) dia.
KV31100300
(J25689-A)
Pin punch
NT410
Removing and installing retaining pin
a: 4.5 mm (0.177 in) dia.
ST30031000
(J22912-O1)
Puller
NT411
Removing 3rd, 5th input gear
Removing 3rd & 4th and 5th & Rev synchronizer
hub
Removing mainshaft rear bearing
Removing 2nd gear, 5th gear bush
Removing 1st & 2nd synchronizer hub, 1st and
4th main gear
Removing and installing differential side bearing
a: 90 mm (3.54 in) dia.
b: 50 mm (1.97 in) dia.
ST30021000
(J22912-O1)
Puller
NT411
Removing input shaft front and rear bearing
Installing input shaft front and rear bearing
Installing 5th input gear, 3rd main gear and 4th
main gear
Installing 1st & 2nd, 3rd & 4th and 5th & Rev syn-
chronizer hub
Installing 2nd gear bush, 5th gear bush, Rev gear
bush
Installing mainshaft rear bearing
a: 110 mm (4.33 in) dia.
b: 68 mm (2.68 in) dia.
PREPARATION
Special Service Tools
MT-2
Tool number
(Kent-Moore No.)
Tool name Description
ST33061000
(J8107-2)
Drift
NT073
Removing differential side bearing
a: 39 mm (1.54 in) dia.
b: 29.5 mm (1.16 in) dia.
ST33290001
(J34286)
Puller
NT414
쐌Removing idler gear bearing outer race
a: 250 mm (9.84 in)
b: 160 mm (6.30 in)
ST33230000
(J25805-O1)
Drift
NT084
Removing differential oil seal
Installing differential side bearing
a: 51 mm (2.01 in) dia.
b: 28.5 mm (1.122 in) dia.
ST30720000
(J25405)
Drift
NT115
Installing differential side bearing outer race
(F70A and clutch housing side of F70V)
a: 77 mm (3.03 in) dia.
b: 55.5 mm (2.185 in) dia.
ST22350000
(J25678-O1)
Drift
NT065
Installing input shaft front and rear bearing
a: 34 mm (1.34 in) dia.
b: 28 mm (1.10 in) dia.
ST22452000
(J34335)
Drift
NT065
Installing 3rd and 4th main gear
Installing 5th gear bush
Installing 5th & Rev synchronizer hub
Installing Rev gear bush
Installing mainshaft rear bearing
a: 45 mm (1.77 in) dia.
b: 36 mm (1.42 in) dia.
ST37750000
(J34335)
Drift
NT065
Installing input shaft oil seal
Installing 5th synchronizer
Installing mainshaft rear bearing
Installing 5th main gear
Installing 3rd & 4th synchronizer hub
Installing striking rod oil seal
Installing clutch housing dust seal
a: 40 mm (1.57 in) dia.
b: 31 mm (1.22 in) dia.
GI
MA
EM
LC
EC
FE
CL
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
PREPARATION
Special Service Tools (Cont’d)
MT-3
Specyfikacje produktu
| Marka: | Nissan |
| Kategoria: | Automatyczny |
| Model: | Sentra (2001) |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Nissan Sentra (2001), zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Automatyczny Nissan
15 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
13 Października 2024
13 Października 2024
8 Października 2024
4 Października 2024
3 Października 2024
18 Września 2024
Instrukcje Automatyczny
- Automatyczny Peugeot
- Automatyczny Citroën
- Automatyczny Pioneer
- Automatyczny Fiat
- Automatyczny Honda
- Automatyczny Audi
- Automatyczny Volkswagen
- Automatyczny Saab
- Automatyczny Toyota
- Automatyczny GEM
- Automatyczny Opel
- Automatyczny Kia
- Automatyczny Dacia
- Automatyczny Subaru
- Automatyczny Ford
- Automatyczny Tesla
- Automatyczny Seat
- Automatyczny BMW
- Automatyczny Mini
- Automatyczny Land Rover
- Automatyczny Mazda
- Automatyczny Skoda
- Automatyczny Vauxhall
- Automatyczny Chrysler
- Automatyczny Volvo
- Automatyczny Suzuki
- Automatyczny Genesis
- Automatyczny Hyundai
- Automatyczny VDL
- Automatyczny Mercury
- Automatyczny Smart
- Automatyczny Jeep
- Automatyczny GMC
- Automatyczny Polaris
- Automatyczny Mercedes-Benz
- Automatyczny Lexus
- Automatyczny MG
- Automatyczny Alfa Romeo
- Automatyczny Chevrolet
- Automatyczny Jaguar
- Automatyczny Maserati
- Automatyczny DS
- Automatyczny Renault
- Automatyczny Mitsubishi
- Automatyczny Buick
- Automatyczny Audio-Technica
- Automatyczny RAM
- Automatyczny Rover
- Automatyczny Dodge
- Automatyczny Infiniti
- Automatyczny Lancia
- Automatyczny Tata
- Automatyczny Acura
- Automatyczny ACME
- Automatyczny Saturn
- Automatyczny Cadillac
- Automatyczny Pontiac
- Automatyczny Porsche
- Automatyczny Polestar
- Automatyczny Scion
- Automatyczny Sharper Image
- Automatyczny Abarth
- Automatyczny Lincoln
- Automatyczny Mahindra
- Automatyczny Chery
- Automatyczny Lada
- Automatyczny Aston Martin
- Automatyczny McLaren
Najnowsze instrukcje dla Automatyczny
15 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
12 Stycznia 2025
11 Stycznia 2025