Instrukcja obsługi Nexa MYCR-250

Nexa Niesklasyfikowane MYCR-250

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Nexa MYCR-250 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Safety and information
Indoor range: up to 30 m (optimal conditions). The range is
strongly dependent on local conditions, such as the presence
of metals. For example, the thin metal coating in Low-emissivity
(Low-E) glass has a negative impact on the range of radio signals.
There may be restrictions on the use of this device outside the
EU. If applicable, check whether this device complies with local
directives.
Maximum load: Never connect lights or equipment that exceed
the maximum load of the receiver, as it can result in defects, a
short circuit or fire.
Life-support: Never use Nexa products for life-support systems
or other applications in which equipment malfunctions can have
life-threatening consequences.
Interference: All wireless devices may be subject to interference,
which could affect performance. The minimum distance between
2 receivers should be at least 50 cm.
Repairing: Do not attempt to repair this product. There are no
user-serviceable parts inside.
Water-resistance: This product is not water-resistant. Keep it dry.
Moisture will corrode the inner electronics and can result in a short
circuit, defects and shock hazard.
Cleaning: Use a dry cloth to clean this product. Do not use harsh
chemicals, cleaning solvents, or strong detergents.
Environment: Do not expose the product to excessive heat or
cold, as it can damage or shorten the life of electronic circuit
boards.
ENGLISH
Plug-in receiver with on/off button on the receiver. Works with
System Nexa remote controls, transmitters and the Nexa Bridge.
This is a self-training system, so installation is very easy and flexible.
INSTALLATION
Connect the load to the receiver. Make sure that the load does not
exceed the output specified under “Dimmer settings” in the table.
PROGRAMMING
1. Connect the receiver (plug-in) to a power socket. The receiver
goes into setup mode as soon as it is powered up.
2. Press the “ON” button for the selected channel on any System
Nexa remote control within 6 seconds.
PROGRAMMING CONFIRMATION
The LED indicator on the receiver flashes rapidly. If a light is
connected to the receiver, this flashes twice.
DELETING MEMORY
1. To delete a memory slot, remove the receiver (plug-in) from the
wall socket
2. Wait at least 6 seconds
3. Reconnect the receiver to a wall socket
4. Press the “OFF” button for the selected channel on the System
Nexa remote control within 6 seconds.
To delete all storage locations, repeat steps 1-3 above, then press
the “ALL OFF” button on the System Nexa control within 6 seconds.
CONFIRMATION OF DELETION
The LED indicator on the receiver flashes rapidly. If a light is
connected to the receiver, this flashes twice.
MEMORY SLOTS
Every MYCR-3500 plug-in receiver has 32 memory slots. When
memory slot 32 is occupied, slot 1 is overwritten during setup.
CONTROL
The plug-in receiver can be controlled in a number of ways.
1. With a System Nexa remote control
2. With other programmed System Nexa transmitters
3. With the On/Off button on the plug-in receiver
4. With a Nexa Bridge
DIMMER SETTINGS
MYCR-250 is supplied set for leading edge dimming and can be set
to trailing edge dimming.
Selection of an appropriate setting is dependent on the type of
load to be connected – see the table below. Contact the place of
purchase for your luminaire/light if you are not sure what type of
load is to be set.
LOAD SETTING OUTPUT
Halogen lamps and bulbs Trailing edge 25-250W /220-240V W RL
Electronic transformers Trailing edge 20-250W / 220-240V
Dimmable LED and
low-energy bulbs Trailing edge 3-120W / 220-240V
Conventional transformers Leading edge 40-250W / 220-240V
SWITCH BETWEEN LEADING EDGE AND TRAILING EDGE
DIMMING
1. Switch on the connected charge using the ON/OFF button on the
receiver.
2. Press and hold down the ON/OFF button on the receiver for 10
seconds.
3. The LED indicator on the receiver flashes in series of 4.
4. Briefly press the ON/OFF button to toggle between leading edge
and trailing edge dimming.
5. The LED indicator on the receiver flashes quickly and the
connected (light) flashes twice and then dims to the set minimum
level in order to confirm the new setting.
The LED indicator shows the set dimming method every time MYCR-
250 is switched on or off using the ON/OFF button.
LED flashes once = Leading edge dimming
LED flashes twice = Trailing edge dimming
SETTING THE MINIMUM DIMMER LEVEL
1. Switch on the connected charge using the ON/OFF button on the
receiver.
2. Press and hold down the ON/OFF button on the receiver for
3 seconds.
3. The LED indicator on the receiver flashes in series of 2.
4. Use a programmed remote control to adjust the minimum dimmer
level. ON increases the level by one step, OFF decreases the level by
one step (4 steps in total).
5. Briefly press the ON/OFF button to save the minimum dimmer level set.
6. The LED indicator on the receiver flashes quickly and the connected
(light) flashes twice and then dims to the set minimum level in order
to confirm the new setting.
Note: MYCR-250 is a universal type dimmer. To avoid damage to the
receiver it has to be set up for the type of load that is connected to it,
see ”Dimmer settings” for more information.
THIS PRODUCT SUPPORTS SMART MODE.
Devices that support Smart Mode can save up to 3 different
favourite scenarios, and these can be activated easily using a
Nexa Smart Mode transmitter.
PÅ/AV-knapp
och LED
ON/OFF button
and LED
NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN
info@nexa.se | www.nexa.se
MYCR-250
PLUG-IN DIMMER
TECHNICAL DATA
Declaration of conformity is available at www.nexa.se
MYCR-250
Power supply 220-240 V~50 Hz
Max. load 20–250 W R/RC / 40–250 W RL / 1.1A
Max. load LED 3–120 W LED
Frequency System Nexa (433,92 MHz)
Range upp till 30 m
Memory slots 32
Power consumption < 1 W (standby)
Built in protective device Temperature fuse
IP rating Inomhusbruk / Indoor use
Size 53 x 53 x 58 mm

Specyfikacje produktu

Marka: Nexa
Kategoria: Niesklasyfikowane
Model: MYCR-250

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Nexa MYCR-250, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Nexa

Nexa

Nexa Bridge X Instrukcja

9 Października 2024
Nexa

Nexa MGDR-3500/SET Instrukcja

9 Października 2024
Nexa

Nexa MWTT-2 Instrukcja

9 Października 2024
Nexa

Nexa MWTE-1 Instrukcja

9 Października 2024
Nexa

Nexa WBT-2201 Instrukcja

3 Października 2024
Nexa

Nexa LDR-075 Instrukcja

3 Października 2024
Nexa

Nexa MYCR-2 Instrukcja

3 Października 2024
Nexa

Nexa WT-1 Instrukcja

3 Października 2024
Nexa

Nexa WTE-2 Instrukcja

3 Października 2024
Nexa

Nexa CMA-968 10Y Instrukcja

3 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024