Instrukcja obsługi Nexa AD-147

Nexa Niesklasyfikowane AD-147

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Nexa AD-147 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
AD-147
Plug-in mottagare Dimmer/
Plug-in receiver Dimmer
Svenska
AD-147 är en liten Z-Wave plug-in dimmermottagare som enkelet ansluts
mellan lasten och eluttaget. Den kan styras av Nexa Bridge eller annan
kontroller som är Z-Wavecertierad. AD-147 har en knapp för att kunna slås
av och på utan fjärrkontroll.
Säkerhet
Läs igenom hela instruktionen först.
Anlita fackman vid behov. Nexa kan ej hållas ansvarig om den användas till
annat än den är designad för eller om instruktionen inte följs. Anslut aldrig
lampor eller utrustning som överskrider mottagarens maximala belast-
ning. Det kan leda till fel, kortslutning eller brand. Försök inte att reparera
produkten. Den innehåller inga reparerbara delar. Produkten är inte vattentät.
Se till att den alltid är torr. Använd inte kemikalier, lösningsmedel eller starka
rengöringsmedel. Utsätt inte produkten för stark värme eller kyla.
Teknisk information
Inspänning 230 V ~50 Hz
Last 6-250 W resistiv last
Frekvens Z-Wave (868,42 MHz)
Räckvidd Upp till 30 m
Dimensioner Ø52 x 78 mm
Arbetstemperatursområde -10°C - 40°C
IP klassicering IP20
Installation
Stoppa i plug-in mottagaren i vägguttaget. Stoppa i lastens kontakt i plug-in
mottgaren.
AD-147 kommer ihåg sitt tillstånd om strömmen bryts och sedan kommer
tillbaka (t.ex. vid strömavbrott). Detta kan ändras i Z-Wave-kontrollenheten.
Inkludering i Z-Wave nätverk
På enheten nns en knapp [Link Key] som används för att inkludera, exklu-
dera, och återställa. Se vidare i manualen för Z-Wavekontrollern hur enheten
inkluderas eller exkluderas.
När inget nod-id nns lagrat blinkar LED:en i 0,5 Hz.
Autoinkludering
Om enheten inte har har ett nod-id och spänningssätts så sätts den automa-
tiskt i inkluderingsläge i 4 minuter.
Inkludera Tryck 3 gånger på [Link Key] inom 1,5 sekunder.
Exkludera Tryck 3 gånger på [Link Key] inom 1,5 sekunder.
Återställning Tryck 3 gånger på [Link Key] inom 1,5 sekunder.
Tryck, inom 1 sekund, och håll [Link Key] nedtryckt
tills dess att LED slocknar.
Enheten är nu återställd och ställer sig i autoinklu-
deringsläge.
För information angånde programmering av Z-Wave modulen, se baksidan.
Användning
Styrning med Z-Wavekontroller
Se manualen till din Z-Wavekontroller för information hur du styr din motta-
gare.
Styrning med knappen [Link key]
Tryck en gång för att tända. Tryck igen för att släcka. För att dimra, håll
knappen intryckt när lampan är tänd. Lampan kommer att tändas med den
ljusstyrka den hade när den släcktes.
mer information på:
www.nexa.se/zwave
English
AD-147 is a small Z-Wave plug-in dimmer receiver that easly is connected
between wall socket and load. It can be controlled by Nexa Bridge or other
Z-Wave controller. AD-147 has a button for control without a remote.
Safety
Read the instructions rst.
Call in professional as needed. Nexa can not be held responsible if it is used
for other purposes than it is designed for, or if instructions are not followed.
Never connect the lights or equipment that exceeds the recipient’s maximum
load. It can lead to failure, short circuit or re. Do not attempt to repair the
product. It contains no serviceable parts. The product is not waterproof.
Make sure it is completely dry. Do not use chemicals, solvents or harsh
detergents. Do not expose to extreme heat or cold.
Technical information
Power supply 230 V ~50 Hz
Load 6-250 W resistive load
Frequency Z-Wave (868,42 MHz)
Range Up to 30 m
Dimensions Ø52 x 78 mm
Environment temp. range -10°C - 35°C
IP classication IP20
Installation
Put the plug-in receiver in the wall socket. Put the loads plug in the receiver.
AD-147 is able to remember the status of the relay when power is cut o
(such as power black-out). When power is supplied again, the unit will resu-
me the last status of the relay (on or o) automatically. This can be changed
in the Z-Wave controller.
Adding to a Z-Wave network
The button marked [Link Key] on the unit is used to include, exclude and
reset the unit.
See Z-Wave controller manual how inclusion/exclusion is done.
The Led ashes 0.5 Hz when no Node ID is stored.
Auto inclusion
If the unit has no Node ID and is powered it enters auto inclusion mode for
4 minutes.
Include Press [Link Key] 3 times within 1,5 seconds.
Exclude Press [Link Key] 3 times within 1,5 seconds.
Reset Press [Link Key] 3 times within 1,5 seconds. Then,
within 1 seconds, press and hold [Link Key] until
LED turns o.
The unit is now reset and enters auto inclusion
mode.
For more information regarding how to program the Z-wave unit, see the
other side.
Operation
Operation with Z-Wave controller
See Z-Wave controller’s manual.
Operation with the button [Link key]
Push once to turn on light, push once again to turn o. Push and hold when
light is on to dim. When the light is turned back on, it will have the same light
intensity as it had when turned o.
more information at:
www.nexa.se/zwave
ad147_86802_manual_002 | 1
Z-Wave Group Support
The unit supports two association groups with 1 node support for Grouping 1 and 4 nodes
support for Grouping 2. This has the eect that when the unit is operating, all devices
associated with the unit will receive the relevant reports.
• When the unit is powered up and is already a part of a Z-Wave network, the unit will send
a Notication Report to the node in Group 1.
• When setting the unit or changing the unit’s status, the unit will send a Multilevel Switch
Report to the node of Group 1.
• When performing Reset the unit will send Device Reset Locally Notication to the node
of Group1.
• The minimum interval time between two reports sent from this unit to the node of Group 1
is 3 seconds. Refer to Conguration parameter 2 for more information.
• When the button on the unit or the wall switch (S1) is pressed, the unit will send a Basic
Set command to the nodes of Group 2. When the unit is OFF, Basic Set Value = 0x00.
When the unit is ON, Basic Set Value = 0xFF.
Z-Wave Plus Info
Role Type Node Type Installer Icon User Icon
Slave Always On Z-Wave Plus node Light Dimmer Switch Light Dimmer Switch
Version
Protocol Library 3 (Slave_Enhance_232_Library)
Protocol Version 3.95 ( 6.51.02)
Manufacturer
Manufacturer ID Product Type Product ID
0x0060 0x0003 0x0003
AGI (Association Group Information) Table
Group Prole Command Class & Command (List)
N bytes
Group Name(UTF-8)
1General:NA Multilevel Switch Report,
Notication Report,
Device Reset Locally Notication
Lifeline
2 Basic SetControl:Key1 On/O control
(Button1)
Basic
• Basic Get: Inquire about the status of the device.
• Basic Report: Report the status of the device.
• Basic Set: Set the status of the device.
Basic Set Value Description
0x00 Device OFF
0x01 ~ 0x63 Device ON, output Level as the specied Value.
0xFF Device ON, output Level as the last memorized Level.
Notication
The device will send notications (Notication Type =0x08, Event = 0x01) upon being
powered on.
Conguration
The congurable values are as following:
Basic Set Command value:
Parameter Number DefaultSize Range
120~99 , 255(0xFF) 255 (0xFF)
The delaying time to report to Group 1:
Parameter Number DefaultSize Range
2 1 33 - 25 (seconds)
Remember the last status:
Parameter Number DefaultSize Range
311/0 1: remember
(0: do not remember)
Output mode setting: Dimming, On/O
Parameter Number DefaultSize Range
511/0 1: Dimming
(0: On/O)
Note: When set to 1, the operation mode is not changed; only the light would be turned on
with 100% brightness immediately.
Command Classes
The module supports Command Classes including…
• COMMAND_CLASS_ZWAVEPLUS_INFO_V2
• COMMAND_CLASS_VERSION_V2
• COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
• COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1
• COMMAND_CLASS_ASSOCIATION_V2
• COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
• COMMAND_CLASS_POWERLEVEL_V1
• COMMAND_CLASS_BASIC_V1
• COMMAND_CLASS_NOTIFICATION_V4
• COMMAND_CLASS_CONFIGURATION_V1
• COMMAND_CLASS_SWITCH_MULTILEVEL
• COMMAND_CLASS_SWITCH_ALL_V1
• COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
Additional Command Classes Supported
• Power Level: For test purpose during product installation.
• Multilevel Switch: Refer to Basic.
• Switch All: The device turns on when receiving “Switch All On”, and turns o upon
receiving “Switch All O”.
• Firmware Update: For OTA function.
Programming
Is herewith conrmed to comply with the requirements set out in the Council
Directive on the Approximation of the Laws of the Member States relating to
Radio Equipment and Telecommunications Terminal Equipment (RED) Directive
2014/54/EU, Low-voltage Directive (2014/35/EU). For the evaluation regarding the
Directives, the following standards were applied:
EN301489-1 V1.9.2
EN301489-3 V1.6.1
EN300220-1 V2.4.1
EN300220-2 V2.4.1
EN61058-1: 2002/A2: 2008
DIN VDE 0620-2-1: 2013
Company Name: Nexa Trading AB
Adress: Karl Johansgatan 152, 40242, Göteborg, Sweden
Signatur: _ __
Name: Erik Hjelmström
Title: Vice President
Date, Place: 17 May 2016, Göteborg
DECLARATION OF CONFORMITY
ad147_86802_manual_002 | 2

Specyfikacje produktu

Marka: Nexa
Kategoria: Niesklasyfikowane
Model: AD-147

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Nexa AD-147, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Nexa

Nexa

Nexa Bridge X Instrukcja

9 Października 2024
Nexa

Nexa MGDR-3500/SET Instrukcja

9 Października 2024
Nexa

Nexa MWTT-2 Instrukcja

9 Października 2024
Nexa

Nexa MWTE-1 Instrukcja

9 Października 2024
Nexa

Nexa WBT-2201 Instrukcja

3 Października 2024
Nexa

Nexa LDR-075 Instrukcja

3 Października 2024
Nexa

Nexa MYCR-2 Instrukcja

3 Października 2024
Nexa

Nexa WT-1 Instrukcja

3 Października 2024
Nexa

Nexa WTE-2 Instrukcja

3 Października 2024
Nexa

Nexa CMA-968 10Y Instrukcja

3 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024