Instrukcja obsługi Netgear SRX5308

Netgear Niesklasyfikowane SRX5308

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Netgear SRX5308 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
)NSTALLATION'UIDE
ProSafe® Gigabit Quad WAN SSL VPN Firewall SRX5308
Start Here
Follow these instructions to set up your VPN firewall. You can also consult the
online Reference Manual http:// or the NETGEAR Knowledge base at
kbserver.netgear.com. A link to the online Reference Manual is on the ProSafe
® Gigabit
Quad WAN SSL VPN Firewall SRX5308 Resource CD.
Prepare to Install Your Firewall
This guide provides instructions for setting up a simple dual WAN port rollover
configuration. Refer to the Reference Manual for other WAN port configuration options.
First, Connect the SRX5308
1. Connect the cables between the SRX5308, two modems, and a computer
a. Turn off unplug the broadband modems.and
b. Insert an Ethernet cable from a modem into the WAN1 port of the SRX5308.
c. Insert an Ethernet cable from the other modem into the WAN2 port of the
SRX5308.
d. Insert the Ethernet cable that came with your VPN firewall into a LAN port on
the firewall and insert the other end into the Ethernet port of your computer.
Your network cables are connected and you are ready to restart your network.
2. Restart your network in the correct sequence
2 41 3 5
Warning: Failure to restart your network in the correct sequence could prevent you
from connecting to the Internet.
a. First, power on the broadband modems. Wait approximately 2 minutes until they
power up.
b. Now, power on the SRX5308.
c. Last, turn on your computer.
d. Before configuring your SRX5308, check the status lights to verify the
following:
1 - Power (green). The power light should turn solid green. If it does not turn
solid green, see the Troubleshooting section of the full manual.
2 -Test (amber). When you first turn on the router, the amber test light will be lit
for approximately 2 minutes. If it is still on after several minutes, see the
Troubleshooting Tips below.
3 - LAN (green/amber). Each port has a green light on the left side of the port. If
on the port has a link, if it blinks, the port is active. Each port has a green and
amber light on the right side of the port. If the green light is on, the port is
1000Mbps, if the amber light is on, the port is 100Mbps, if neither light is on, the
port is 10Mbps. If a LAN light is not lit, ensure that its Ethernet cable is securely
attached at both ends, and that the computer is turned on.
4 - WAN (green/amber). Each port has a green light on the left side of the port
and a green and amber light on the right side of the port. The lights operate the
same as the LAN lights described above.
5 - DMZ (green): If this light is on, the port is configured as a DMZ port.
Next, Configure the SRX5308 for Internet Access
Before you begin, be sure you have the configuration parameters from your ISP handy.
1. Log in to the firewall
a. Use a browser to connect to https://192.168.1.1
Note: To connect to the firewall, your computer needs to be configured to obtain an IP
address automatically via DHCP. If you need instructions on how to do this, please refer to
the online reference manual. A link to the manual is on your ProSafe
® Gigabit Quad WAN
SSL VPN Firewall SRX5308 Resource CD.
b. For security reasons, the
firewall has its own user name
and password.
When prompted, enter admin
for the firewall User Name and
password for the firewall Pass-
word.
c. Click You are now connected to the firewall. Login.
The Web Support tab on the main menu contains links to the online NETGEAR
SRX5308 product documentation and support Knowledge base. Be aware that
the default login time-out is 5 minutes of inactivity, after which automatic logout
will occur.
d. Click , Network Configuration WAN Settings WAN . The screen will display.
A table of settings for the WAN ports is shown.
2. Connect to the Internet
a. Click on the Edit button at the right of the WAN1 row. The WAN1 ISP Settings
screen will be displayed. Click Auto Detect WAN1 ISPat the bottom of the
Settings screen. The firewall will automatically attempt to detect your
connection type. If you know your ISP connection type, you can manually
configure the firewall settings on the WAN1 ISP screen. If connecting manually,
click Apply to save your settings.
b. When finished, click Test to verify that the Internet connection is active.
c. Select the WAN2 ISP tab and complete the same steps you completed in steps a
and b.
SRX5308_IG.fm Page 1 Friday, December 14, 2012 12:37 PM
December 2012
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks
of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to
change without notice. Other brand and product names are registered trademarks or trademarks of their
respective holders. © NETGEAR, Inc. All rights reserved.
Intended for indoor use only in all EU member states, EFTA states, and Switzerland.
Now, Configure WAN Rollover Mode
The WAN ports of the firewall can be configured for either rollover for increased system
reliability or load balancing for maximum bandwidth efficiency. The rollover option is
presented here. Refer to the manual for instructions on configuring the load balancing
mode.
In rollover mode, expect the following:
• You designate one WAN port as primary and the other as the rollover link.
• While the primary link is up, all traffic goes over the primary WAN port. If the
primary link goes down, traffic is sent over the rollover link.
• Traffic will automatically roll back to the primary link once it is back up.
To configure the dual WAN ports for rollover:
1. Select WAN Mode WAN Mode from the sub-menu. The screen will display.
2. From the Auto-Rollover pull-down menu, select which WAN port will be primary.
3. WAN failure is detected using DNS queries to the DNS server or PING messages to
an IP address. If the replies are not received, the WAN interface is considered down.
Fill in the appropriate fields:
• Configured DNS Servers – In this case, DNS queries are sent to the ISP DNS
servers configured on the WAN ISP pages.
• Using this DNS Server – In this case, DNS queries are sent to a specified DNS
Server.
• Ping to this IP address – In this case, PING queries are sent to the specified IP
address.
• Test Period – a DNS or PING query is sent after every test period. The minimum
test period is 30 seconds.
• Failover after – The WAN link is considered down after the configured number
of queries fail to get a reply. The minimum number of failed queries is four. The
rollover link is brought up after this.
4. Click Apply to save your changes.
Troubleshooting Tips
Here are some tips for correcting common problems you may encounter.
Be sure to restart your network in this sequence:
1. Turn off and unplug the modems, turn off the SRX5308, and shut down the computer.
2. Plug in and turn on the modems. Wait for the modems to power up (approximately 2
minutes).
3. Turn on the SRX5308. Wait until the amber test light goes out.
4. Turn on the computer.
Make sure the Ethernet cables are securely plugged in.
• The WAN Link/Act light on the VPN firewall will be lit if the Ethernet cable to the
VPN firewall from each modem is plugged in securely and the modems and VPN
firewall are turned on.
• For each powered on computer connected to the VPN firewall with a securely
plugged in Ethernet cable, the corresponding VPN firewall LAN port status light
should be lit. The front of the SRX5308 identifies the number of each LAN port.
Make sure the network settings of the computer are correct.
Computers be configured to obtain IP DNS addresses automatically via DHCP. must and
For help with this, please see the online Reference Manual; a link to the manual is on the
ProSafe® Gigabit Quad WAN SSL VPN Firewall SRX5308 Resource CD.
For Cable Modem connections, use MAC spoofing.
Some cable modem ISPs require that you use the MAC address of the computer registered
on the account. If so, in the Router’s MAC Address section (accessed through the
Advanced WAN1 ISP Settings link on the screen), select either “Use this Computer’s
MAC” or “Use this MAC address” and enter the appropriate MAC address. The firewall
will then capture and use the MAC address of the computer that you identified. You must
select the computer that is registered with the ISP. Click Apply to save your settings.
Restart the network in the correct sequence.
Use the SRX5308 status lights to verify correct operation.
If the SRX5308 Test light does not go out approximately 2 minutes after turning the
firewall on, reset the fiewall as described in the Reference Manual.
Technical Support
After installing your device, locate the serial number on the label of your product and use
it to register your product at https://my.netgear.com.
You must register your product before you can use NETGEAR telephone support.
NETGEAR recommends registering your product through the NETGEAR website.
For product updates and web support, visit http://support.netgear.com.
NETGEAR recommends that you use only the official NETGEAR support resources.
You can get the reference manual online at http://downloadcenter.netgear.com or through
a link in the product’s user interface.
For the current EU Declaration of Conformity, visit
http://support.netgear.com/app/answers/detail/a_id/11621/.
SRX5308_IG.fm Page 2 Friday, December 14, 2012 12:37 PM

Specyfikacje produktu

Marka: Netgear
Kategoria: Niesklasyfikowane
Model: SRX5308

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Netgear SRX5308, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Netgear

Netgear

Netgear FV318 Instrukcja

14 Października 2024
Netgear

Netgear Nighthawk X6S R7960P Instrukcja

13 Października 2024
Netgear

Netgear GS108Ev4 Instrukcja

9 Października 2024
Netgear

Netgear Orbi RBE972SB Instrukcja

9 Października 2024
Netgear

Netgear Orbi RBK652S Instrukcja

9 Października 2024
Netgear

Netgear Nighthawk MS90 Instrukcja

9 Października 2024
Netgear

Netgear Nighthawk MK93S Instrukcja

9 Października 2024
Netgear

Netgear MS308 Instrukcja

9 Października 2024
Netgear

Netgear Orbi RBEWM Instrukcja

9 Października 2024
Netgear

Netgear Orbi RBKWMB Instrukcja

9 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024