Instrukcja obsługi NEC MultiSync LT81
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla NEC MultiSync LT81 (55 stron) w kategorii Beamer. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/55
Part No. 78409942
Printed in Japan
Ultra-Portable Projector
Ultra-Portable Projector
Projector
User’s Manual
NEC Technologies, Inc.
1250 N. Arlington Heights Road, Suite 500
Itasca, Illinois 60143-1248
MultiSync
®
LT 81
™
/100
™
NEC Technologies
RF Interference
WARNING
The Federal Communications Commission does not allow any modifications or
changes to the unit EXCEPT those specified by NEC Technologies in this
manual. Failure to comply with this government regulation could void your
right to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
commercial installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at their own
expense.
DOC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian Interfer-
ence-Causing Equipment Regulations.
WARNING
TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE. DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN
EXTENSION CORD OR IN AN OUTLET UNLESS ALL THREE PRONGS
CAN BE FULLY INSERTED. DO NOT OPEN THE CABINET. THERE ARE
HIGH-VOLTAGE COMPONENTS INSIDE. ALL SERVICING MUST BE
DONE BY QUALIFIED NEC SERVICE PERSONNEL.
2
Precautions
Please read this manual carefully before using your NEC MultiSync LT81/LT100 Projector and keep the manual handy for future reference.
Your serial number is located beneath the main power switch on the back of your MultiSync LT81/LT100. Record it here:
CAUTION
To turn off main power, be sure to remove the plug from power outlet. The power outlet socket quipment asshould be installed as near to the e
possible, and should be easily accessible.
I M P O R T A N T I N F O R M A T I O N
CAUTION
LASER RADIATION-
DO NOT STARE INTO BEAM
WAVE LENGTH: 670 nm
MAX. OUTPUT: 1 mW
CLASS II LASER PRODUCT
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
NEC SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the
unit may be sufficient to cause electrical shock. Therefore, it is
dangerous to make any kind of contact with any part inside of
the unit.
This symbol alerts the user that important information concern-
ing the operation and maintenance of this unit has been pro-
vided. The information should be read carefully to avoid prob-
lems.
1
CAUTION
LASER RADIATION-
DO NOT STARE INTO BEAM
WAVE LENGTH: 645 nm (640-660 nm)
MAX. OUTPUT: 1 mW
CLASS II LASER PRODUCT
LT100 Remote Control LT81 Remote Control
Cleaning
1. Unplug the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild
detergent. Never use strong detergents or solvents such as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to scratch or
mar the lens.
Lamp Replacement
• Perform lamp replacement in accordance with the instructions on page 81.
• Be sure to replace the lamp when the Status light comes on. If you continue
to use the lamp after 1000 hours of use, the lamp bulb may shatter, and pieces
of glass may be scattered in the lamp case. Do not touch them as the pieces of
glass may cause injury. If this happens, contact your NEC dealer for lamp
replacement.
• Allow a minimum of ONE minute to elapse between turning the lamp off and
on. High voltage is applied to the lamp immediately when the power is turned
on. Therefore turning the power off and quickly back on may shorten the life
of your lamp and result in damage to your projector.
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are unobstructed to
prevent the build-up of heat inside your projector. Allow at least 3 inches
(10cm) of space between your projector and a wall.
2. Prevent foreign objects such as paper clips and bits of paper from falling into
your projector. Do not attempt to retrieve any objects that might fall into your
projector. Do not insert any metal objects such as a wire or screwdriver into
your project. If something should fall into your projector, disconnect it
immediately and have the object removed by a qualified NEC service person.
3. Do not place any liquids on top of your projector.
• Do not look into the lens while the projector is on. Serious
damage to your eyes could result.
• Do not look into the laser pointer while it is on and do not point
the laser beam at another person. Serious injury could result.
4
Important Safeguards
These safety instructions are to ensure the long life of your projector and to
prevent fire and shock. Please read them carefully and heed all warnings.
Installation
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away from dust and
moisture.
3. Do not place your projector in direct sunlight, near heaters or heat radiating
appliances.
4. Exposure to direct sunlight, smoke or steam can harm internal components.
5. Handle your projector carefully. Dropping or jarring can damage internal
components.
6. Do not place heavy objects on top of the projector.
7. If installing the projector on the ceiling:
a. The ceiling must be strong enough to support the projector and the
installation must be in accordance with any local building codes.
b. The projector must be installed by qualified NEC service personnel.
Power Supply
1. The projector is designed to operate on a power supply of 100-120 or 220-240
V 50/60 Hz AC. Ensure that your power supply fits this requirement before
attempting to use your projector.
2. Handle the power cable carefully and avoid excessive bending. A damaged
cord can cause electric shock or fire.
3. If the projector is not to be used for an extended period of time, disconnect the
plug from the power outlet.
3
Specyfikacje produktu
| Marka: | NEC |
| Kategoria: | Beamer |
| Model: | MultiSync LT81 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z NEC MultiSync LT81, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Beamer NEC
16 Września 2024
7 Września 2024
6 Września 2024
6 Września 2024
5 Września 2024
5 Września 2024
4 Września 2024
1 Września 2024
1 Września 2024
31 Sierpnia 2024
Instrukcje Beamer
- Beamer Sony
- Beamer Yamaha
- Beamer Samsung
- Beamer LG
- Beamer Sharp
- Beamer Lenovo
- Beamer Philips
- Beamer Livoo
- Beamer Acer
- Beamer Epson
- Beamer Hisense
- Beamer Panasonic
- Beamer Canon
- Beamer Viewsonic
- Beamer Asus
- Beamer OK
- Beamer Toshiba
- Beamer Blaupunkt
- Beamer Salora
- Beamer Casio
- Beamer HP
- Beamer Steinel
- Beamer Kodak
- Beamer Smart
- Beamer ZTE
- Beamer JVC
- Beamer Dell
- Beamer Eurolite
- Beamer Ricoh
- Beamer Renkforce
- Beamer Pyle
- Beamer Marantz
- Beamer Showtec
- Beamer Mitsubishi
- Beamer XGIMI
- Beamer Polaroid
- Beamer Sanyo
- Beamer Optoma
- Beamer Barco
- Beamer 3M
- Beamer Nebula
- Beamer Hitachi
- Beamer RCA
- Beamer BenQ
- Beamer Overmax
- Beamer Adj
- Beamer Elmo
- Beamer Reflecta
- Beamer Yaber
- Beamer Derksen
- Beamer InFocus
- Beamer Naxa
- Beamer Vivitek
- Beamer Ibm
Najnowsze instrukcje dla Beamer
18 Września 2024
18 Września 2024
17 Września 2024
16 Września 2024
16 Września 2024
16 Września 2024
16 Września 2024
16 Września 2024
15 Września 2024
15 Września 2024