Instrukcja obsługi NAV-TV NTV-KIT483

NAV-TV kamera samochodowa NTV-KIT483

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla NAV-TV NTV-KIT483 (4 stron) w kategorii kamera samochodowa. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
BHM
09/28/15
NTV-DOC 154
rB4
Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. :
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
1 | P a g e
3950 NW 120th Ave, Coral Springs, FL 33 TEL 561-955-9770 FAX 561-955-9760 065
www.nav-tv.com info@nav-tv.com
MB Sprinter-CAM
NTV-KIT477
Overview
The MB Sprinter-CAM allows the user to add an aermarket rear camera to the factory screen on the
Mercedes Sprinter. If desired, forced camera is an opon through a mounted toggle switch (not included).
ATTENTION: This module locks the VIN and can only be used on ONE vehicle at a me. to
Kit Contents
Plug & Play T Harness
NTV-HAR 081
SMB to RCA Adapter
NTV-CAB007
USB Cable (updates)
NTV-CAB009
MB Sprinter-CAM
Module
NTV-ASY171
CAN-XG Adapter
NTV-HAR058
BHM
09/28/15
NTV-DOC 154
rB4
Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. :
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
2 | P a g e
Module Pin Outs
PIN #
Color
1
Yellow
2
Red
3
Blue
4
Pink
8
White/Green
9
Brown/Black
10
Black
17
Green
18
Brown
Installaon
1. Remove the factory radio. This requires pulling panels and removing screws. Disconnect all connected
harnesses and set the radio aside.
2. Connect the male end of the factory 44-pin plug to the female end of the provided Plug & Play T-
Harness.
3. Disconnect the two smaller plugs on the factory 44-pin plug and connect
them both to the male end of the provided Plug & Play T-Harness.
4. Connect the harness to the 8-pin plug located in the center of the CAN-XG Adapter Plug & Play T-
Harness.
5. Connect the to the 18-pin Molex MB Sprinter-CAM module
connector on the end of the . CAN-XG Adapter
Wire Side
BHM
09/28/15
NTV-DOC 154
rB4
Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. :
If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger
entertainment only.
3 | P a g e
6. Connect the provided to the green port on the back of the SMB to RCA Adapter
Sprinter’s factory radio (if there is already a plug at the green port, disconnect it and
use the provided SMB cable instead).
7. Aer installing and running the reverse camera to the dash
opening (connect power to an ACC source, NOT reverse!),
connect the camera’s signal lead to the RCA side of the SMB
to RCA Adapter Note: ACC power in Mercedes can oen be .
found at the cigaree lighter.
8. Connect the male end of the provided 44-pin Plug & Play T-
Harness leave the module outside of the dash, or accessible. back to the radio and
9. Proceed to .Programming (below)
10. Once programming is complete, start the vehicle and place it into
reverse. The reverse camera’s image should appear on the screen
automacally.
11. Oponal: If forced camera is desired, connect one side of a toggle
switch (not included) to ACC, and the other side to INPUT 3 (pink).
Acvang this switch will force the rear camera in any gear (reverse
camera must be powered with ACC and a reverse wire!) not
Module Programming
1. Begin by installing this kit (page 2, steps 1-9).
2. From the 18-pin Molex connector, nd the labeled Blue wire Input 2.
3. Cut the metal connector o of the and strip the end back. blue wire
4. Connect this wire to 12v (+). temporarily When programming is complete, you must remove this wire
from power! Note: the yellow wire on the white 8-PIN molex connector is CAN wire, not constant a
power Use the RED wire in this plug (constant 12v) or the yellow wire from 18-PIN XG module. .
5. Turn (not ACC or running, but the vehicle’s ignion ON ON).
6. Wait at least for the radio to fully boot and sele. 1 minute
7. With connected to 12v (+), and Input 2 toggle (pull and release once) the high-beam head lamp lever
‘DIAGNOSIS’ will appear on the screen. Refer to the chart below during programming.
8. Once the radio has been programmed, it will shut down (not reboot, but turn o).
9. Aer a few seconds, press the on the radio to bring the radio back up. power buon
10. Remove Input 2 from 12v (+). Insulate the wire end.
11. Connue with installaon: step 10.

Specyfikacje produktu

Marka: NAV-TV
Kategoria: kamera samochodowa
Model: NTV-KIT483

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z NAV-TV NTV-KIT483, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje kamera samochodowa NAV-TV

NAV-TV

NAV-TV NTV-KIT457 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-KIT839 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-KIT877 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-KIT705 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-KIT508 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-KIT870 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-KIT518 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-MIS071 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-KIT788 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-KIT589 Instrukcja

6 Sierpnia 2024

Instrukcje kamera samochodowa

Najnowsze instrukcje dla kamera samochodowa

Garmin

Garmin nuviCam LMTHD Instrukcja

15 Stycznia 2025
Rexing

Rexing V33 Instrukcja

14 Stycznia 2025
Navman

Navman DDR MiVue 740 Instrukcja

14 Stycznia 2025
Navman

Navman Smart Box II Instrukcja

14 Stycznia 2025
Alpine

Alpine PKG-RSE3DVD Instrukcja

12 Stycznia 2025
Alpine

Alpine HCE-C257FD Instrukcja

11 Stycznia 2025
Hikvision

Hikvision AE-DC5313-C6PRO Instrukcja

11 Stycznia 2025
Minolta

Minolta MNCD406X Instrukcja

10 Stycznia 2025
IRoad

IRoad X10 Pro Instrukcja

7 Stycznia 2025
Sencor

Sencor SCR 3400 Instrukcja

6 Stycznia 2025