Instrukcja obsługi NAV-TV NTV-KIT175

NAV-TV kamera samochodowa NTV-KIT175

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla NAV-TV NTV-KIT175 (6 stron) w kategorii kamera samochodowa. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
BHM
01/13/13
NTV-DOC166
Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for :
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
1 | P a g e
3950 NW 120th Ave, Coral Springs, FL 33 TEL 561-955-9770 FAX 561-955-9760 065
www.nav-tv.com info@nav-tv.com
GVIF-JAG
NTV-KIT175
Overview
The GVIF- Kit allows the user to add up to 3 video inputs and a backup camera input to the JAG
factory media screen in select Jaguar vehicles Audio integraon requires that the vehicle have .
a factory audio input.
Kit Contents
AV Input Harness
Power/CAN Harness
GVIF Video cable
GVIF- Interface JAG
Remote
RGB Input cable
Input Toggle Switch
IR Eye Harness
BHM
01/13/13
NTV-DOC166
Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for :
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2 | P a g e
Interface Connectors
Dip Switch Sengs* Congure prior to installaon
Dip SW:
1
2
5
6
7
8
UP
Enables
RGB
Enables
V1
Resoluon
adjust
Aermarket
NAV
Factory or
no Rev-Cam
N/A
DOWN
Skips
RGB
Skips
V1
Resoluon
adjust
Factory
NAV
Acvates
aermarket
Rev-Cam
N/A
AV IN/OUT
Power/CAN
Dip Switches
Status LEDs
*Note: If the dip switches are not congured prior to
installaon you must remove power to the unit prior to
making adjustments to the dip switches. When power is
reconnected aer the dip switch adjustment the new
sengs will be stored into memory.
LCD IN/OUT
(LVDS Cable)
Touch
IN/OUT
TX/RX
BHM
01/13/13
NTV-DOC166
Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for :
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3 | P a g e
Installaon
1. Locate the factory navigaon drive and gain access to the connectors. The drive usually
can be found in the trunk. Disconnect any connected harnesses to the NAV drive
temporarily .
2. Gather the provided from the GVIF- kit. Connect the ‘Power/CAN Harness’ JAG
following wires to the car:
Note: CAN connecon is not supported at this me. You must connect the GRAY wire
to a reverse lamp for reverse acvaon!
3. Disconnect the factory GVIF cable from the NAV drive, this is a
square, blue connector.
4. Connect the X provided male side (labeled ‘L IN’) of the GVIF video
cable to the NAV drive .
5. Connect the free end (removed in step 3) of the factory GVIF
video cable to the female side of the provided GVIF video cable (labeled ‘LXOUT’).
6. Connect the white end of the GVIF video cable to the interface at the port labeled ‘GVIF
IN/OUT’.
7. Connect the AV Input cable to the port on the GVIF- interface labeled JAG ‘AV IN/OUT’.
If you’re only connecng a reverse camera (and no other
inputs), the signal input from the camera must connect
to the RCA labeled . Refer to the dip-‘REAR-C’
switch sengs chart to skip/enable AV sources
upon toggle switch presses (oponal. Page 2 ).
8. Ad JAGjust dip switches on the GVIF- interface properly, refer to the chart on page 2 for
qualicaons.
9. Connect the white plug from the to the port on the GVIF- ‘Power/CAN Harness’ JAG
interface labeled ‘Power/CAN’.
Interface wires
Connect to car
Black (GND)
Chassis Ground
Red (ACC)
Accessory
Gray (Rear)
Reverse lamp 12v (if adding rear camera)

Specyfikacje produktu

Marka: NAV-TV
Kategoria: kamera samochodowa
Model: NTV-KIT175

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z NAV-TV NTV-KIT175, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje kamera samochodowa NAV-TV

NAV-TV

NAV-TV NTV-KIT457 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-KIT839 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-KIT877 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-KIT705 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-KIT508 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-KIT870 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-KIT518 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-MIS071 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-KIT788 Instrukcja

6 Sierpnia 2024
NAV-TV

NAV-TV NTV-KIT589 Instrukcja

6 Sierpnia 2024

Instrukcje kamera samochodowa

Najnowsze instrukcje dla kamera samochodowa

Garmin

Garmin nuviCam LMTHD Instrukcja

15 Stycznia 2025
Rexing

Rexing V33 Instrukcja

14 Stycznia 2025
Navman

Navman DDR MiVue 740 Instrukcja

14 Stycznia 2025
Navman

Navman Smart Box II Instrukcja

14 Stycznia 2025
Alpine

Alpine PKG-RSE3DVD Instrukcja

12 Stycznia 2025
Alpine

Alpine HCE-C257FD Instrukcja

11 Stycznia 2025
Hikvision

Hikvision AE-DC5313-C6PRO Instrukcja

11 Stycznia 2025
Minolta

Minolta MNCD406X Instrukcja

10 Stycznia 2025
IRoad

IRoad X10 Pro Instrukcja

7 Stycznia 2025
Sencor

Sencor SCR 3400 Instrukcja

6 Stycznia 2025