Instrukcja obsługi NAD 414

NAD Audio tuner 414

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla NAD 414 (52 stron) w kategorii Audio tuner. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/52

414

• OWNER'S MANUAL

• MANUEL D'INSTALLATION

• BEDIENUNGSANLEITUNG

• MANUAL DEL USUARIO

• MANUALE DELLE ISTRUZIONI

• MANUAL DO PROPRIETÁRIO

• BRUKSANVISNING

Warning: To reduce the risk of fire or electric shock, do not expose this

unit to rain or moisture.

The graphic symbol of a lightning flash with an arrow point within a trian-

gle signifies that there is dangerous voltage within the unit and it

poses a hazard to anyone removing the cover to gain access to the

interior of the unit. Only qualified service personnel should

make any such attempt.

The graphic symbol of an exclamation point within an equilateral trian-

gle warns a user of the device that it is necessary to refer to the

instruction manual and its warnings for proper operation of the unit.

Do not place this unit on an unstable cart, stand or tripod,

bracket or table. The unit may fall, causing serious injury to a

child or adult and serious damage to the unit. Use only with a

cart, stand, tripod, bracket or table recommended by the man-

ufacturer or sold with the unit. Any mounting of the device on a

wall or ceiling should follow the maufacturer’s instructions and

should use a mounting accessory recommended by the manu-

facturer.

An appliance and cart combination should be moved with care. Quick stops,

excessive force and uneven surfaces may cause the appliance and cart combi-

nation to overturn.

Read and follow all the safety and operating instructions before connecting or

using this unit. Retain this notice and the owner’s manual for future reference.

All warnings on the unit and in it’s operating instructions should be adhered to.

Do not use this unit near water; for example, near a bath tub, washbowl, kitchen

sink, laundry tub, in a wet basement or near a swimming pool.

The unit should be installed so that its location or position does not interfere with

its proper ventilation. For example, it should not be situated on a bed, sofa, rug

or similar surface that may block the ventilation openings; or placed in a built-in

installation, such as a bookcase or cabinet, that may impede the flow of air

through its ventilation openings.

The unit should be situated from heat sources such as radiators, heat registers,

stoves or other devices (including amplifiers) that produce heat.

The unit should be connected to a power supply outlet only of the voltage and

frequency marked on its rear panel.

The power supply cord should be routed so that it is not likely to be walked on or

pinched, especially near the plug, convenience receptacles, or where the cord

exits from the unit.

Unplug the unit from the wall outlet before cleaning. Never use benzine, thinner

or other solvents for cleaning. Use only a soft damp cloth.

The power supply cord of the unit should be unplugged from the wall outlet when

it is to be unused for a long period of time.

Care should be taken so that objects do not fall, and liquids are not spilled into

the enclosure through any openings.

This unit should be serviced by qualified service personnel when:

A. The power cord or the plug has been damaged; or

B. Objects have fallen, or liquid has been spilled into the unit; or

C. The unit has been exposed to rain or liquids of any kind; or

D. The unit does not appear to operate normally or exhibits a marked change in

performance; or

E. The device has been dropped or the enclosure damaged.

DO NOT ATTEMPT SERVICING OF THIS UNIT YOURSELF.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

Upon completion of any servicing or repairs, request the service shop’s assur-

ance that only Factory Authorized Replacement Parts with the same characteris-

tics as the original parts have been used, and that the routine safety checks

have been performed to guarantee that the equipment is in safe operating condi-

tion.

REPLACEMENT WITH UNAUTHORIZED PARTS MAY RESULT IN FIRE,

ELECTRIC SHOCK OR OTHER HAZARDS.

ATTENTION

POUR PREVENIR LES CHOCS ELECTRIQUES NE PAS UTILIER

CETTE FICHE POLARISEE AVEC UN PROLONGATEUR, UNE

PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT,

SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS

EN LAISSER AUCUNE PARTIE A DECOUVERT.

CAUTION

TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED

PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER

OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO

PREVENT BLADE EXPOSURE.

If an indoor antenna is used (either built into the set or installed separately),

never allow any part of the antenna to touch the metal parts of other electrical

appliances such as a lamp, TV set etc.

CAUTION

POWER LINES

Any outdoor antenna must be located away from all power lines.

OUTDOOR ANTENNA GROUNDING

If an outside antenna is connected to your tuner or tuner-preamplifier, be sure

the antenna system is grounded so as to provide some protection against volt-

age surges and built-up static charges. Section 810 of the National Electrical

Code, ANSI/NFPA No. 70-1984, provides information with respect to proper

grounding of the mast and supporting structure, grounding of the lead-in wire to

an antenna discharge unit, size of grounding conductors, location of antenna dis-

charge unit, connection to grounding electrodes and requirements for the

grounding electrode.

a. Use No. 10 AWG (5.3mm2) copper, No. 8 AWG (8.4mm2) aluminium, No. 17

AWG (1.0mm2) copper-clad steel or bronze wire, or larger, as a ground wire.

b. Secure antenna lead-in and ground wires to house with stand-off insulators

spaced from 4-6 feet (1.22 - 1.83 m) apart.

c. Mount antenna discharge unit as close as possible to where lead-in enters

house.

d. Use jumper wire not smaller than No.6 AWG (13.3mm2) copper, or the equiva-

lent, when a separate antenna-grounding electrode is used. see NEC Section

810-21 (j).

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL

CODE INSTRUCTIONS CONTAINED IN ARTICLE 810 - RADIO AND TELEVI-

SION EQUIPMENT.

NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to

call the CATV system installer’s attention to Article 820-22 of the

National Electrical Code that provides guidelines for proper grounding

and, in particular, specifies that the ground cable ground shall be con-

nected to the grounding system of the building, as close to the point of

cable entry as practical.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

ATTENTION:

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).

ATTENTION: AFIN DEVITER UN CHOC ELECTRIQUE, ET LES CONSEQUENCES GRAVES QUI

POURRAIENT EN RESULTER, TENTEZ PAS D'OUVRIR L'APPAREIL ET DE TOUCHER AUX

COMPOSANTS INTERNES SANS LA PRESENCE D'UNE SERVICE PERSONNEL.

THE FOLLOWING PRECAUTIONS AND SAFETY INSTRUCTIONS

ARE REQUIREMENTS OF UL AND CSA SAFETY REGULATIONS

REAR PANEL CONNECTIONS

FIGURE 1. FIGURE 2.

FRONT PANEL CONTROLS

Australian version only

European version only

Specyfikacje produktu

Marka:	NAD
Kategoria:	Audio tuner
Model:	414
Kolor produktu:	Black,Yellow
Typ produktu:	Multimetr cyfrowy
Źródło zasilania:	Bateria
Wysokość produktu:	198.1 mm
Szerokość produktu:	100 mm
Głębokość produktu:	63.5 mm
Waga produktu:	698.5 g
Typ ekranu:	LCD
Zakres częstotliwości:	0.0005 - 199.99 kHz
Rodzaj baterii:	AA
Liczba baterii:	3
Napięcie baterii:	1.5 V
Walizka:	Tak
Zakres napięcia DC:	0.0001 - 1000 V
Dokładność (napięcie DC):	0.05% + 1
Zakres napięcia AC:	0.0001 - 1000 V
Dokładność (napięcie AC/przemienne):	0.7% + 4
Zakres prądu DC:	0.000001 - 10 A
Dokładność (prąd DC):	0.2% + 4
Zakres prądu AC:	0.000001 - 10 A
Dokładność (prąd AC):	1.0% + 2
Zakres rezystancji:	0.1 - 50000000 Ω
Zakres pojemności:	1 - 9999000 nF
Zakres pomiaru temperatury:	-200 - 1090 °C
Kategoria pomiarowa:	CAT III 1000V,CAT IV 600V
Przewody testowe:	Tak