Instrukcja obsługi Monitor Audio Creator C3L

Monitor Audio Speaker Creator C3L

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Monitor Audio Creator C3L (11 stron) w kategorii Speaker. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/11
Product Manual
Creator Series
Register your speakers using the QR code
or visit monitoraudio.com/registration
Register your Creator Series speakers
to ensure the best possible product and customer support
2
CAUTION: The Creator Series loudspeakers can only be ixed into plasterboard (dry-lined) or
suspended ceilings (in-ceiling models), with a thickness of up to 35mm (excluding the Super
Slim series, which can be ixed up to 15mm) and walls (in-wall models), with a thickness of up
to 30mm. Solid wall installation will require channelling out and framework constructed to
provide a structure for the Tri Grip dog legs to clamp to. For safety reasons, if you are unsure
of your ability to provide a secure and safe ixing, do not attempt to ix these speakers,
please obtain the services of a competent and qualiied trades person.
CAUTION: Ensure that there are no water pipes or electricity cables running within the wall
or ceiling structure before cutting the speaker apertures. Work from secure steps and avoid
trailing wires.
Do not over tighten the Tri-Grip Dog Leg clamps. Over tightening the clamping mechanism on
any in ceiling/ in wall speaker can result in damage to the speaker mounting hardware, ceiling/
wall or speaker frame, and/or delection in the speaker frame during installation.
If you notice any of the above during installation, you have over tightened the Tri Grip Dog Leg.
Back o the mounting screw until delection is reduced to allow the product to sit irmly against
the ceiling or wall.
IMPORTANT: Do not exceed 5Kgf/cm (4.34 lbf/inch.) or 0.5 NM when tightening
the Tri Grip dog leg screws.
When using a cordless screwdriver/ drill to install this product ensure the clutch is set to its
lowest setting to avoid over-tightening and damaging the mounting hardware.
Before you unpack your speakers, please make sure that there is plenty of available loor space.
Inside the carton, you will ind a cut-out template that you can use the mark and cut into your
ceilings or walls to the correct size, you’ll also ind your Quik-Link terminal and grille in the box.
Preparing your installation
Overtightening warning

Specyfikacje produktu

Marka: Monitor Audio
Kategoria: Speaker
Model: Creator C3L

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Monitor Audio Creator C3L, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Speaker Monitor Audio

Instrukcje Speaker

Najnowsze instrukcje dla Speaker

Mission

Mission ZX-5 Instrukcja

1 Października 2024
Audibax

Audibax Party 12 Instrukcja

1 Października 2024
Audibax

Audibax Ground 6T Instrukcja

1 Października 2024
Meridian

Meridian DSP7200 S Instrukcja

1 Października 2024
DAP-Audio

DAP-Audio CS-36 Instrukcja

1 Października 2024
Mission

Mission ZX-1 Instrukcja

1 Października 2024
Audibax

Audibax PR42T Instrukcja

1 Października 2024
Meridian

Meridian DSP7200.2HC Instrukcja

1 Października 2024
Mission

Mission QX-1 MKII Instrukcja

1 Października 2024
Audibax

Audibax Ground 4T Instrukcja

1 Października 2024