Instrukcja obsługi Monacor KP70-400

Monacor Niesklasyfikowane KP70-400

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Monacor KP70-400 (3 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
Manufactured by :
CRC Industries Europe BVBA
Touwslagerstraat 1 – 9240 Zele – Belgium
Tel (32) (0) 52/45.60.11 Fax (32) (0) 52/45.00.34
www.crcind.com
TECHNICAL DATA SHEET
1/3
PLASTIK 70
Ref. : 20743
1. GENERAL DESCRIPTION
Quick drying, colorless transparent insulating and protective coating based on acrylic resins.
2. FEATURES
• PLASTIK 70 is a low viscosity, solvent drying acrylic based conformal coating with
excellent insulating properties. The lacquer is colorless transparent and elastic. It has a
durable adhesion in the temperature range from –40°C to +60°C and can be used for a
short period of time up to +100°C maximum. It protects printed circuit boards and
surfaces from humid inorganic-acid or caustic vapors.
• PLASTIK 70 is colorless-transparent and as such is not visual on the printed circuit board
surface.
• Contains “moisture warning”: To avoid involuntary encapsulations of moisture, Plastik 70
will warn you when applied on a humid surface, by showing a frosted, mat appearance.
• For repair works PLASTIK 70 can be soldered through or be totally removed with
acetone, THINNER FOR PLASTIK 70.
3. APPLICATIONS
PLASTIK 70 was specially developed to protect printed circuit boards. It overcomes electrical
leakages and short circuits.
As a low viscosity xing and insulating lacquer, PLASTIK 70 can also be used as extra/after
insulation of coils and transformers and overcomes disturbing noises.
PLASTIK 70 can also be used as a universal protective coating on any surface like metal,
paper, ornaments, paintings, furniture, etc.
4. DIRECTIONS
• For small runs and service applications, the easiest way to apply PLASTIK 70 is from an
aerosol can. Spray from a distance of 20 to 30 cm on the dry and degreased surface. As
pre-cleaning of PCB’s, we do recommend the use of KONTAKT PCC to remove greases,
dirt and ux residues. When nished spraying, clean the aerosol valve by turning the can
upside down and pressing the button until only propellant escapes.
• For serial production runs, PLASTIK 70 in bulk can be applied by brush or by dipping. For
spraying, two parts per volume PLASTIK 70 is diluted with up to one part of THINNER
FOR PLASTIK 70. The precise mixing ratio must be determined by trials with the
equipment concerned.
• For dip coating it is also necessary to x the immersion time and the withdrawal speed.
The faster the removal from the bulk, then thicker the lm will be. Dipping baths have to
be carefully protected to ensure no entrapment of conductive stuck-on residues.
Manufactured by :
CRC Industries Europe BVBA
Touwslagerstraat 1 – 9240 Zele – Belgium
Tel (32) (0) 52/45.60.11 Fax (32) (0) 52/45.00.34
www.crcind.com
TECHNICAL DATA SHEET
2/3
PLASTIK 70
Ref. : 20743
• PLASTIK 70 contains solvents like ethyl acetate and butyl acetate. Printed circuit board
materials and electronic components generally have a good compatibility with these
solvents. In case of plastic surfaces (e.g. housings) a compatibility test is always
recommend. It is necessary in particular, to test its suitability for plastics susceptible to
stress cracking (e.g. polycarbonate).
• PLASTIK 70 contains ammable solvents and hence when working with the product,
make sure there is good ventilation in the workplace. Remove all possible ignition
sources.
• A safety data sheet (MSDS) according to EU directive 91/155/EEC and amendments is
available for all CRC products.
5. TYPICAL PRODUCT DATA (without propellant)
As delivered
Coverage at 20µm, calculated : ±0.7m²/200 ml spray
±9m²/litre
Viscosity bulk : 10-20 mPas
Flashpoint : <0°C
Drying time at 20°C (dry to touch) : ±20 minutes
Properties dry lm
(after 24 hrs drying at ambient temperature, thickness 20-40 µm)
Aspect : colorless-transparent
Surface resistivity at 20°C : >10
13 Ω
Volume resistivity at 20°C : >10
13 .cm Ω
Dielectric strength : >80kV/mm
Adhesion to copper plates, measured at ambient temperature
following 6 hrs at –40°C : Gt 0-1
following 6 hrs at +60°C : Gt 0-1
following ½ hr at +100°C : Gt 0-1
Manufactured by :
CRC Industries Europe BVBA
Touwslagerstraat 1 – 9240 Zele – Belgium
Tel (32) (0) 52/45.60.11 Fax (32) (0) 52/45.00.34
www.crcind.com
TECHNICAL DATA SHEET
3/3
PLASTIK 70
Ref. : 20743
6. PACKAGING
aerosol : 12 x 200 ml
12 x 400 ml
Bulk : 1 Liter , 5 Liter
All statements in this publication are based on service experience and/or laboratory testing. Because of the wide
variety of equipment and conditions and the unpredictable human factors involved, we recommend that our
products be tested on-the-job prior to use. All information is given in good faith but without warranty neither
expressed nor implied.
This Technical Data Sheet may already have been revised at this moment for reason such as legislation,
availability of components and newly acquired experiences. The latest and only valid version of this Technical
Data Sheet will be sent to you upon simple request or can be found on our website: . www.crcind.com
We recommend you to register on this website for this product so you will be able to receive any future updated
version automatically.
Version : 20743 03 1003 03
Date : 14 January 2014

Specyfikacje produktu

Marka: Monacor
Kategoria: Niesklasyfikowane
Model: KP70-400

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Monacor KP70-400, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Monacor

Monacor

Monacor WP-1 Instrukcja

8 Października 2024
Monacor

Monacor PA-1200RDSU Instrukcja

20 Września 2024
Monacor

Monacor RF-EXPLORER/3 Instrukcja

20 Września 2024
Monacor

Monacor KKS75-400 Instrukcja

20 Września 2024
Monacor

Monacor EX-40/8 Instrukcja

20 Września 2024
Monacor

Monacor TY5242MXR Instrukcja

18 Września 2024
Monacor

Monacor ATS-35CB Instrukcja

18 Września 2024
Monacor

Monacor CU-48DMX Instrukcja

17 Września 2024
Monacor

Monacor MEVAC-4 Instrukcja

16 Września 2024
Monacor

Monacor PM-2/30V Instrukcja

16 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

GBC

GBC ThermaBind T500Pro Instrukcja

15 Stycznia 2025
Da-Lite

Da-Lite Parallax 29850 Instrukcja

15 Stycznia 2025
Crivit

Crivit IAN 290909 Instrukcja

15 Stycznia 2025
Tripp Lite

Tripp Lite SmartRack SRW12US Instrukcja

15 Stycznia 2025
Powerfix

Powerfix IAN 280221 Instrukcja

15 Stycznia 2025
AGM

AGM Rattler TC35-640 Instrukcja

15 Stycznia 2025
AGM

AGM Wolf-7 Pro Instrukcja

15 Stycznia 2025
AGM

AGM Anaconda TC50-640 Instrukcja

15 Stycznia 2025
AGM

AGM Secutor Pro TS50-640 Instrukcja

15 Stycznia 2025
Microchip

Microchip AT91SAM9M11 Instrukcja

15 Stycznia 2025