Instrukcja obsługi Mitsubishi WS-73615
Mitsubishi
Telewizja
WS-73615
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Mitsubishi WS-73615 (100 stron) w kategorii Telewizja. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/100

TV Information:
Use this space to record the model and serial numbers of your television.
This information is on the back of your TV.
Model number
Serial number
v i s i t o u r w e b s i t e a t
w w w. m i t s u b i s h i -t v.c o m
TM
TM
Projection Television
Owne r’s G u ide
WS - 4 8 515 WS - 55 515 WS - 6 5515 WS -73 615
WS - 55 615 WS - 6 5515A
WS -55 615A WS - 6 5 615
WS - 6 5615A

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of
the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be sufficient
magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by Mitsubishi could cause harmful interference
and would void the user’s authority to operate this equipment.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S
ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR THE PROPER GROUNDING AND,
IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM
OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL.
CAUTION: To assure continued FCC compliance, the user must use a shielded video interface cable
with bonded ferrite cores at both ends.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Warning: To avoid permanently imprinting a fixed image onto your TV screen, please do not display the same
stationary images on the screen for more than 15% of your total TV viewing in one week. Examples of stationary
images are letterbox top/bottom bars from DVD disc or other video sources, side bars when showing standard
TV pictures on widescreen TVs, stock market reports, video game patterns, black or bright Closed Caption
backgrounds, station logos, web sites or stationary computer images. Such patterns can unevenly age the picture
tubes causing permanent damage to the TV. Please see pages 12 and 54 for a detailed explanation.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This TV is very heavy! Exercise extreme care when moving TV as foreign material may become
embedded in the castor wheels which could damage wood or other delicate flooring.

Chapter 1 Television Overview
TV Accessories .....................................................8
Special Features ...................................................8
Front Control Panel ...............................................9
Back Panel ..........................................................10
Important Notes ...................................................12
Chapter 2 Connecting
External Devices
& NetCommand® Setup ......................................14
Wall Outlet Cable or Cable Box ...........................15
Single Analog Antenna.........................................16
Separate UHF and VHF Antennas .......................16
VCR Video and Audio to an Antenna
or Wall Outlet Cable .............................................17
VCR Video and Audio to a Cable Box..................18
A/V Receiver or Stereo System ..........................19
Satellite Receiver or Other Device
with S-Video.........................................................19
DVD Player with Component Video ....................20
DVI Device ............................................................20
HDMI Device ........................................................21
External DTV Receiver with Component Video ...21
IR Emitter NetCommand® ...................................22
IEEE 1394 Devices ...............................................23
IEEE 1394 Device Connection Styles ..................24
CableCARD™ Definition and Initial
Screen Display .....................................................25
Helpful Hints.........................................................26
Chapter 3 NetCommand® Setup and Editing
NetCommand® Pre-Memorized Devices ............28
Remote Control Functions: Overview ..................29
Remote Control Functions: Operation,
Care, Sleep Timer ................................................30
NetCommand® OnScreen Buttons .....................31
3D Graphical Menu System .....................32
NetCommand® Initial Setup................................33
Edit NetCommand®
Adding an A/V Receiver.................................35
Adding Devices ..............................................38
Changing, Deleting Devices,
Finish Screen .................................................42
Device Selection Menu ........................................43
Using the Device Menu Button to
Display Menus......................................................44
Chapter 4 IEEE 1394 Devices and
NetCommand® Controlled Recordings
Adding IEEE 1394 Devices Automatically............46
IEEE 1394 Devices Compatibility.........................48
Using the Guide Button to Display
ChannelView™ and Menus ..................................49
NetCommand® Controlled Recordings ..............50
Direct VCR Recording .........................................52
NetCommand® Controlled Peer-to-Peer
Connections .........................................................53
Important Notes ...................................................54
Chapter 5 TV Menu Screen Operations
Main Menu Choices .............................................56
Setup Menu..........................................................57
NetCommand® Menu..........................................59
Antenna Menu......................................................60
Time Menu ...........................................................62
Captions Menu.....................................................63
V-Chip Lock Menu ...............................................65
Audio Video Menu................................................68
A/V Setting Descriptions .....................................69
Chapter 6 Special Features
Display Formats ..................................................72
Operation of PIP and POP ...................................74
Device Menu with NetCommand® ......................75
Appendix A: Bypassing the V-Chip Lock ............77
Appendix B: High Definition Input
Connection Compatibility ....................................79
Appendix C: Remote Control
Programming Codes ............................................80
Appendix D: On-Screen Information
Displays................................................................83
Appendix E: NetCommand® Specialized
Device Keys .........................................................84
Appendix F: Cleaning and Service ......................85
Appendix G: Diamond Shield™ Removal............86
Appendix H: Cabinet Separation ........................89
Troubleshooting .................................................90
Additional Information..........................................94
Index.....................................................................95
Warranty...............................................................97
Contents

4
IMPORTANT SAFEGUARDS
Please read the following safeguards for your TV and retain for future reference. Always follow all
warnings and instructions marked on the television.
1. Read, Retain and Follow All Instructions
Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions
for future reference. Follow all operating and use instructions.
2. Heed Warnings
Adhere to all warnings on the appliance and in the operating instructions.
3. Cleaning
Unplug the TV from the wall outlet before cleaning. Do not use liquid, abrasive, or aerosol cleaners. Cleaners
can permanently damage the cabinet and screen. Use a lightly dampened cloth for cleaning.
4. Attachments and Equipment
Never add any attachments and/or equipment without approval of the manufacturer as such additions may result
in the risk of fire, electric shock or other personal injury.
5. Water and Moisture
Do not use the TV where contact with or immersion in water is possible. Do not use near bath tubs, wash bowls,
kitchen sinks, laundry tubs, swimming pools, etc.
6. Accessories
Do not place the TV on an unstable cart, stand, tripod or table. The TV may fall, causing
serious injury to a child or adult and serious damage to the TV. Use only with a cart, stand,
tripod, bracket or table recommended by the manufacturer, or sold with the TV. Any
mounting of the TV should follow the manufacturer’s instructions, and should use mounting
accessories recommended by the manufacturer.
An appliance and cart combination should be moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance and cart combination to overturn.
7. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the TV and to
protect it from overheating. Do not block these openings or allow them to be obstructed by placing the TV on a
bed, sofa, rug, or other similar surface. Nor should it be placed over a radiator or heat register. If the TV is to be
placed in a rack or bookcase, ensure that there is adequate ventilation and that the manufacturer’s instructions
have been adhered to.
8. Power Source
This TV should be operated only from the type of power source indicated on the marking label. If you are not sure
of the type of power supplied to your home, consult your appliance dealer or local power company.
9. Grounding or Polarization
This TV is equipped with a polarized alternating current line plug having one blade wider than the other. This plug
will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
10. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the TV.
11. Lightning
For added protection for this TV during a lightning storm, or when it is left unattended and unused for long
period of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent
damage to the TV due to lightning and power-line surges.

5
IMPORTANT SAFEGUARDS, cont’d.
12. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits as contact with them might be
fatal.
13. Overloading
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
14. Object and Liquid Entry
Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or
short-out parts that could result in fire or electric shock. Never spill liquid of any kind on or into the TV.
15. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the TV, be
sure the antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electric Code, ANSI/NFPA No. 70-2002,
provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead in wire to an
antenna discharge unit, size of grounding conductors, location of
antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
16. Servicing
Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service personnel.
17. Damage Requiring Service
Unplug the TV from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
(a) When the power-supply cord or plug is damaged.
(b) If liquid has been spilled, or objects have fallen into the TV.
(c) If the TV has been exposed to rain or water.
(d) If the TV does not operate normally by following the operating instructions, adjust only those controls that are
covered by the operating instructions as an improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the TV to its normal operation.
(e) If the TV has been dropped or the cabinet has been damaged.
(f) When the TV exhibits a distinct change in performance - this indicates a need for service.
18. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by
the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in
fire, electric shock or other hazards.
19. Safety Check
Upon completion of any service or repair to the TV, ask the service technician to perform safety checks to
determine that the TV is in safe operating condition.
20. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
ANTENNA
LEAD IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
GROUND CLAMP
ELECTRIC
SERVICE
EQUIPMENT
NEC — NATIONAL ELECTRICAL CODE
EXAMPLE OF ANTENNA GROUNDING

Chapter . . .
1
Television Overview
TV Accessories ..............................................................................................8
Special Features............................................................................................8
Front Control Panel .......................................................................................9
Back Panel .................................................................................................. 10
Important Notes .......................................................................................... 12

8
POWER
HOME
PAUSEREC
FF/FWDREW/REV PLAY
STOP
3
6
9
QV
VOLUME
INFO
EXCH
ENTER
TV MENU DEVICE
MENU
V-CHIP
FORMAT
PIP CH
1
7
SQV
4
DEVICE
SLEEP
VIDEO
AUDIO
MUTE
2
5
8
0
CHANNEL
ADJUST
PIP/POP
PIP DEV ICE
CANCEL
TV AUDIO
CABLE/DBS/DTV DVD
VCR
GUIDE
SUB
CONNECT
TV Accessories
Please take a moment to review the following list of
items to ensure that you have received everything
including:
���
���
1. Remote Control
2. Two AAA Batteries
4. One Quadruple IR Emitter Cable
(allows NetCommand to control other
devices)
3. One Digital Audio Cable (sends
the audio of digital channels to a
digital A/V receiver).
5. Product Registration Card (not pictured)
6. Owner’s Guide (not pictured)
7. Quick Reference Card (not pictured)
Special Features
Your new widescreen High Definition television has
many special features that make it the perfect center
of your home entertainment system, including:
Fully Integrated HDTV
This HDTV can receive all approved terrestrial
broadcast digital signals, non-scrambled digital cable
signals, terrestrial analog signals and non-scrambled
analog cable signals that use a standard offset carrier
system. Your TV will display all signals as 1080i True
HDTV™.
Digital Cable Ready (CableCARD™)
This HDTV is “Plug-and-Play” ready. It can descramble
a cable provider’s one-way digital signals with the use
of a CableCARD security module. The CableCARD is
used in place of a traditional cable box to access digital
cable programming (including high definition). Contact
your local cable provider for availability information and
service details.
NetCommand® Control System
This HDTV offers a new level of networking to
combine selected older products with new and future
digital products. NetCommand supports IEEE 1394
connections with Audio Video Control system (AV/C),
5C copy protection and IR control of selected older
products such as VCRs, DVD players, cable boxes or
satellite receivers. NetCommand includes the ability to
learn remote control signals directly from many devices,
allowing you to customize the NetCommand system in
a way that works best for your viewing.
16:9 Widescreen Picture Format
Enjoy a full theatrical experience in the comfort of your
home. View pictures as film directors intended them.
Digital TV broadcasts, DVDs and newer video game
consoles support this widescreen format.

9
Front Control Panel
SYSTEM RESET
If the TV will not respond to either the remote control
or the front panel controls and/or will not power Off,
press the SYSTEM RESET button with a pointed item
like the end point of a paperclip. The TV will turn Off
and the TIMER light will flash quickly for about one
minute. When the TIMER light stops flashing, you may
turn on the TV again. Changes you made the last time
the TV was On before you used the SYSTEM RESET
button may be lost, however, the changes you made
previously are not lost.
POWER/TIMER Indicator
The green light is a multi-function indicator. This light
will flash rapidly for about one minute each time the TV
is plugged into the wall electrical outlet, when power
is restored after a power failure, or using the SYSTEM
RESET button. Do not attempt to turn on the TV again
during this period. Wait for the flashing to stop and
the light to turn off, before attempting to turn the TV
on. While the TV is powered on, the light illuminates
steadily. If the TV has been programmed to turn on
automatically using the Timer feature, this light will flash
slowly when the TV is powered off.
Except for SYSTEM RESET and TIMER, all of the buttons on the Front Control Panel (highlighted in gray) are
duplicated on the remote control. The top row of labels show the control functions when there are no TV menus
displayed on the screen. The bottom row of labels show the control functions when the TV menus are displayed on
the screen or when a special function has been activated. See Remote Control Overview page 29, for further details
on the functions of these buttons. TIMER is also accessible through the menu screens. Pressing MENU on the front
panel will display the TV menu.
INPUT– 3
POWER DEVICE
ENTERADJUST ADJUST CANCELMENU
VOL CH FORMAT
SYSTEM
RESET
TIMER
MENU S-VIDEO VIDEO L – AUDIO – R
Front Panel WS-48515, WS-55515, WS-65515, WS-65515A
DEVICE
CANCELMENUENTER
MENUFORMAT
CH
VOLPOWER
SYSTEM
RESET
TIMER ADJUSTADJUST
Front Panel WS-55615, WS-55615A, WS-65615, WS-65615A, WS-73615
GUIDE
GUIDE
INPUT-3
S-VIDEO VIDEO L-AUDIO-R
IEEE 1394
A/V RESET
There may be times when you wish to reset the A/V
(Audio and Video) settings back to the factory defaults.
To do this for an individual setting, use the Audio
or Video remote control button. To return all of the
settings at once, press GUIDE and FORMAT on the
front panel at the same time, or use the A/V Memory
Reset selection on the AudioVideo menu (page 68).
INPUT 3
This input can be used for convenient connection of
a camcorder or other video device to the TV. If you
connect to the S-VIDEO terminal, the VIDEO terminal
is deactivated. The VIDEO terminal is available when
there is no S-Video connection.
IEEE 1394 (WS-55615, WS-55615A, WS-65615,
WS-65615A, WS-73615 only)
This IEEE 1394 (FireWire®) input/output allows for
temporary connection of IEEE 1394 devices such as
MPEG 2 camcorders or compatible hard disc drives to
the front of the TV. This connection works the same
way as the two rear IEEE 1394 connections.

10
SERVICE WARNING
X-RAY PRECAUTION:
THIS PRODUCT
I N C L U D E S C R I T I C A L ME C H A N I C A L
A ND EL E C T R I CAL PART S W HI CH AR E
ES SE N TIAL FOR X-R A D IAT IO N SAFE TY.
F O R C O N T I N U E D SA F E T Y R E P L A C E
C R I T I C A L COMP O N E N T S I N D I C AT E D
IN THE SE R VICE MANUAL ON LY WIT H
E X A C T RE P L A C E ME N T PA R T S G I V E N
IN THE PARTS LIST. REFER TO SERVICE
MANUAL FOR OPERATING HIGH VOLTAGE AT
MIN IMUM BRIGHT NE SS, MEA SU R E ME N T
PR O CE D UR E S AN D PR O PE R S E RV I CE
ADJUSTMENTS.
WARNING:
HANDLE WITH CARE. HIGH
VACUUM PICTURE TUBE IS DANGEROUS
TO HAND LE . RE FER SE RVICING TO
Q U A L I F I E D S E R V I C E P E R S O N N E L .
REPLACE WITH A TUBE OF THE SAME
TYPE NUMBER FOR CONTINUED SAFETY.
CAUTION:
TO MEASURE SECOND
ANODE VOLTAGE USE A HIGH VOLTAGE
METER CONNECTED FROM ANODE LEAD
TO CHASSIS ONLY. DISCHARGE HIGH
VOLTAGE TO CHASSIS ONLY, NOT TO
EXTERNAL GROUND.
IR EMITTER
NetCommand R
DIGITAL
SERVICE
PORT
IEEE1394
INPUT/OUTPUT AUDIO
ANT-2
AUX
ANT-1
MAIN
CableCARD
TM SLOT
– –(DTV/CABLE /VHF/UHF)
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
INPUT MONITOR OUTPUT
AUDIO 2
AUDIO/VIDEO 1
1 2
COMPONENT
YPbPr (480i/480p/1080i)
21
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DVI
Digital Video
Digital Audio
Analog Audio
11.
1. 2. 3. 4. 5. 6. 7.
8.
9.
10.
Back Panel
1. IEEE-1394 Input/Output
Use these jacks to connect the TV to external IEEE
1394 digital products by means of a single cable. There
are two jacks on the back panel for all models. For
WS-55615, WS-55615A, WS-65615, WS-65615A and
WS-73615 there is an additional jack on the front
panel. IEEE 1394 connections provide a high degree
of flexibility when connecting your NetCommand®
controlled system. Detailed information regarding IEEE
1394 connection requirements are in Chapter 4.
2. Antenna (ANT-1 MAIN, ANT-2 AUX)
ANT-1 MAIN and ANT-2 AUX can each receive both
digital/analog over-the-air channels from a VHF/UHF
antenna or non-scrambled digital/analog cable
channels.
Your primary viewing signal source should be
connected to ANT-1 MAIN. ANT-1 MAIN must be
used to view premium subscription cable TV service
authorized by the CableCARD™ access card. The
CableCARD access card is provided by your local
cable company. ANT-2 AUX can continue to receive
over-the-air or non-scrambled cable signals.
3. Digital Audio Output
This output will automatically send Dolby® Digital audio
from digital channels, IEEE 1394 devices and HDMI™
(not DVI) signals to a digital Audio/Video receiver.
Connect this output to the A/V receiver’s coaxial digital
audio input. This output will automatically turn off when
viewing an analog channel or device. Use Monitor
Ouput Audio 2 to send analog signals to your A/V
receiver.
Some digital cable channels send MPEG-1 digital audio
instead of Dolby Digital, however, not all A/V receivers
can decode MPEG-1 digital audio. This can cause the
A/V receivers to produce a loud noise that can damage
speakers. For this reason, the TV will automatically
turn off the digital audio output when tuned to a
channel or device that has MPEG-1 digital audio and
send it to the A/V receiver as analog left and right audio
from Monitor Output. You can enable the digital output
to include MPEG-1 digital audio if your A/V receiver
is capable of decoding it. See for Edit NetCommand
details.
4. CableCARD™ Slot
The CableCARD access card provided by your cable TV
service provider is inserted into this slot. CableCARD

11
Back Panel, continued
is a nationwide standard system that allows your local
cable TV provider to supply you with an access card
customized to your account. This card allows the
TV to receive, decode and unscramble the premium
digital channels included in your cable TV subscription
without the use of a cable box. It also allows your
cable provider to automatically update and change your
subscription. See pages 15, 25, and 44 for additional
CableCARD information and activation instructions.
If your cable company is not currently offering
CableCARD, you will need to use an external cable box.
5. HDMI™ or DVI Devices
The HDMI™ interface supports uncompressed
standard, enhanced and high definition digital video
formats. This interface also supports existing digital
multi-channel audio formats. The HDMI input supports
both video and audio using one single cable. Use this
input to connect to EIA/CEA-861 compliant devices
such as a high definition receiver or DVD player. This
input supports the 480i, 480p and 1080i video formats.
It is not intended for use with personal computers
or devices outputting video signals with computer
resolutions.
This input can also be used as a DVI connection
with separate analog audio inputs (see DVI Analog
Audio, below). An optional HDMI-to-DVI adaptor will
be necessary to make this connection and can be
purchased from your local electronics retailer. When
using the optional HDMI-to-DVI adapter, the DVI analog
audio inputs on your TV allow you to receive left and
right audio from your DVI device.
This input is HDCP (High-Bandwidth Digital Copy
Protection) compliant.
6. DVI Analog Audio
Unlike HDMI, DVI does not carry audio information on
the same cable. Use these analog stereo audio inputs
when using the HDMI input with a device that outputs
DVI instead of HDMI.
7. Component Inputs 1-2
YPbPr(480i/480p/1080i)
These inputs can be used for the connection of devices
with component video outputs, such as a DVD player,
external HDTV receiver or compatible video game
system. Please see for signal compatibility.Appendix B
8. IR Output-NetCommand®
Two jacks are provided for connecting IR emitters. IR
Emitters connected to these jacks are used by the
TV’s NetCommand system to control external analog
devices such as VCRs, DVDs, cable boxes, satellite
and audio receivers.
9. Monitor Output (Audio/Video 1, Audio 2)
The Monitor Output sends the TV audio and video
signals from the antennas or Inputs 1-3 to an A/V
Receiver or other analog A/V equipment such as a
VCR. Digital channels and IEEE 1394 signals will be
down converted to analog signals compatible with
traditional analog VCRs. There will be no video signals
from digital channels or IEEE 1394 signals that have
copy restrictions. There will be no video signals from
Monitor Outputs when viewing the Component 1 & 2
inputs or the HDMI input
Monitor Output Audio/Video 1 should be connected to
a VCR for recording. Monitor Output Audio 2 should
be connected to your A/V Receiver for home theater
surround sound.
10. Inputs 1-2
These inputs can be used for the connection of a VCR,
Super VHS (S-VHS) VCR, DVD player, standard satellite
receiver or other A/V device to the TV. Please note
that if you connect to the S-VIDEO terminal, the VIDEO
terminal is deactivated. The VIDEO terminal is available
when there is no S-Video connection.
11. SERVICE PORT
This input is for use by Authorized Mitsubishi Servicers
only.

12
Warning: Do not leave stationary PIP/POP, or letterbox images on the screen
for extended periods of time. Mix the types of pictures shown.
Uneven picture tube aging is NOT covered by your warranty.
The normal use of a TV should include a mixture of TV picture types. The most frequently used picture types
should fill the screen with constantly moving images rather than stationary images or patterns. Displaying the same
stationary patterns over extended periods of time or displaying the same stationary pattern frequently can leave
subtle but permanent ghost images. To avoid this, mix your viewing patterns. Reducing the initial contrast level can
help slow the aging process. Do not show the same stationary image for more than 15% of your total TV viewing in
any given week. Display constantly moving and changing images that fill the screen whenever possible.
This projection TV uses picture tubes to project the image to the screen. All picture tubes age with use. As they age,
their light output is gradually reduced. Normal TV pictures fill the screen with constantly changing images. Under
these conditions, picture tubes age at an even rate across the entire screen. This maintains a TV picture that is
evenly bright over the whole screen. Stationary images or images that only partially fill the screen (leaving black
or colored bars to fill the screen), when used over extended periods of time or when viewed repeatedly, can cause
uneven aging of the phosphors and leave subtle ghosts from the stationary images in the picture.
Still or stationary images may be received from broadcasters, cable channels, satellite channels, DVD discs, video
tapes, laser discs, on-line services, web/Internet searching devices, video games, and digital TV tuner/converter
boxes.
Examples of these types of images can be, but are not limited to the following:
Letterbox top/bottom black bars:
shown at the top and bottom of the TV screen when you watch a widescreen (16:9) movie on a standard (4:3) TV.
Side bar images:
solid bars shown on each side of an image when watching a standard (4:3) program on a widescreen (16:9) TV.
News and stock-market report bars:
ticker running at the bottom of the TV screen.
Shopping channel logos & pricing displays:
bright graphics that are shown constantly or repeatedly in the same location.
Video game patterns and scoreboards
Bright station logos:
moving or low-contrast graphics are less likely to cause uneven aging of the picture tubes.
Online (Internet) websites:
or any other stationary or repetitive computer style images, including digital photos or computer applications/
programs.
Closed Captioning
Mitsubishi recommends using a gray background rather than black or a bright color if you frequently use closed
captioning.
IMPORTANT NOTES

Chapter . . .
2
Connecting
External Devices & NetCommand® Setup ...................................................14
Wall Outlet Cable or Cable Box......................................................................15
Single Analog Antenna or Separate UHF and VHF Antennas ....................16
VCR Video and Audio to an Antenna or Wall Outlet Cable .........................17
VCR Video and Audio to a Cable Box............................................................18
A/V Receiver or Stereo System ....................................................................19
Satellite Receiver or Other Device with S-Video..........................................19
DVD Player with Component Video ..............................................................20
DVI Device ........................................................................................................20
HDMI Device ....................................................................................................21
External DTV Receiver with Component Video............................................21
IR Emitter NetCommand® .............................................................................22
IEEE 1394 Devices ...........................................................................................23
IEEE 1394 Device Connection Styles ............................................................24
CableCARD™ Definition and Initial Screen Display ....................................25
Helpful Hints ....................................................................................................26

14
AV
Receiver
TV
Device to be
connected
stereo and/or digital
audio cables
video and stereo
audio cables
stereo and digital audio cables
IR Emitters
Connecting External Devices & NetCommand
®
Setup
NetCommand is able to control many current audio and video devices by sending remote control signals from the
TV to each device through IR emitters. Additionally, it is able to learn the remote control signals used by most audio
video devices not already in the TV’s memory. NetCommand can automatically switch the TV along with compatible
or learned Audio/Video (A/V) Receivers to the correct input for use with each device. It is important that the inputs
on the TV and A/V Receiver back panel match the NetCommand setup that is displayed on-screen.
To simplify the installation of NetCommand, there is a step-by-step on-screen NetCommand setup procedure in this
chapter, which details the type and brand of devices you are connecting to the TV. The NetCommand Setup also
assigns preset TV and A/V Receiver inputs for each device. You should connect each device to the TV input (both
audio and video) and to the A/V Receiver (audio) as shown in the figure below.
After using NetCommand Setup, you may go to the NetCommand menu (see “Edit NetCommand”) at any time
to change the inputs you used for connecting each device, custom name devices, add devices not included in
the presets above or delete devices no longer used. See Connection Helpful Hints, at the end of this chapter for
additional information on device setup.
The following charts show which preset inputs you should use on the TV and A/V Receiver.
Chart 1 shows TV inputs.
Chart 2 shows the A/V Receiver inputs used by A/V Receiver models already known by NetCommand.
Model
M-VR800 &
M-VR1000
Model
M-VR900 &
M-VR700
Model
Lifestyle ®28
Model
AVR-2700
Model
DTR-9.1
Model
VR-2080
Model
SR8200
Model
VSX-D557
Model
VSX-49TX
Model
RSX-1065
Model
STR-DE825
Model
RV-X2095
Model
RX-V2200
Device Audio Output to AV Receiver Inputs by Name
VCR
VCR 1 VCR VCR VCR-1 Video 1 Video 1 VCR1
VCR/Tape
VCR 1/DVR Video 2 Video 1 VCR 1 VCR 1
Satellite Receiver Aux
Cable/DBS AUX CD Video 3 Video 3 DSS CD SAT Video 4 TV/DBS TV/DBS D-TV/LD
DVD Player
DVD DVD (built-in) DVDVDP DVD Video 4 DVD LD/SAT DVD/LD Video 5 TAPE/MD CD DVD
TV Monitor Output
(& Digital Audio)
TV TV TV TV/DBS Video 4 Video 4 TV DVD/TV TV Video 1 DVD/LD DVD/LD CBL/SAT
Chart 2 Mitsubishi 1 Mitsubishi 2 Bose Denon Integra Kenwood Marantz Pioneer 1 Pioneer 2 Rotel Sony Yamaha 1 Yamaha 2
Chart 1
Device Audio and Video Outputs to TV Inputs
Cable for CableCARD™ Service ANT-1
Antenna/Cable (digital/analog) ANT-1 if primary viewing source,
ANT-2 if secondary viewing source
Cable box ANT-2
VCR Input-1
Satellite Receiver (DBS) Input-2
Camcorder Input-3 (on front panel)
DVD Player Component-1

15
Additional connection cables are
not provided with the TV. They are
available at most electronic stores.
IMPORTANT
Connecting a Wall Outlet Cable or Cable Box
Wall Outlet Cable (can be used with a CableCARD™)
Figure 1
It is very important to connect the incoming
cable for your primary viewing source to ANT-1,
especially for CableCARD™ use.
1. Connect the primary incoming coaxial lead cable to
ANT-1 MAIN on the TV back panel.
2. For an optional secondary antenna source, connect
an antenna (or cable) to ANT-2 AUX.
3. If you have subscribed to a CableCARD™ service,
the CableCARD can now be inserted into the
CableCARD SLOT. Using a phillips screwdriver,
remove the CableCARD cover screws. Insert the
CableCARD, then replace the cover and screws. If
you need more information regarding this service,
please contact your cable service provider.
DIGITAL
SERVICE
PORT
IEEE13 94
INPUT/OUTPUT AUDIO
ANT-2
AUX
ANT-1
MAIN
CableCARD TM SLOT
– –(DTV/CABLE /VHF/UHF)
1.
2.
TV back panel
(section detail)
Optional
Secondary
Antenna
or Cable
Primary
Wall Outlet
Cable
3. CableCARDTM SLOT
(cover removed)
Figure 1. Wall Outlet Cable
Cable Box (compatible with PIP/POP)
Figure 2
3 coaxial cables and one two-way RF splitter are required.
These are not included with the TV.
It is very important to connect the incoming
cable for your primary viewing source to ANT-1,
especially for CableCARD™ use.
1. Connect the incoming cable to IN on an RF splitter.
2. Connect one coaxial cable from OUT on the RF
splitter to ANT-1 MAIN on the TV back panel.
3. Connect one coaxial cable from OUT on the RF
splitter to IN on the cable box.
4. Connect one coaxial cable from OUT on the cable
box to ANT-2 AUX on the TV back panel.
Note: NetCommand® will assume that your
Cable Box is connected as shown above. Also,
that Channel 3 is the default output channel for
the cable box. If either the connections or output
channel are different, use the Change option of
Edit NetCommand to apply the changes.
Figure 2. Connecting a Cable Box
Cable Box
back panel section
IN
DIGITAL
SERVICE
PORT
IEEE1394
INPUT/OUT PUT AUDIO
ANT-2
AUX
ANT-1
MAIN
CableCARD SLOT
– –(DTV/CA BLE /VHF/UHF)
Incoming
Cable
OUT
IN
OUT OUT
TWO WAY SPLITTER
1.
2.
2.
3.
3.
4.
4.
TV back panel (section detail)

16
Separate UHF and VHF Antennas
Figure 4
A UHF/VHF combiner is required. This is not included with
the TV.
1. Connect the UHF and VHF antenna leads to the
UHF/VHF combiner.
2. Push the combiner onto ANT-1 MAIN on the TV
back panel.
External
Antenna
or Cable
Back Side
Flat Twin Lead
UHF Antenna
(Channels 14-69)
VHF Antenna
(Channels 2-13)
300 Ohm to
75 Ohm
Combiner
Flat Twin Lead
UHF
VHF
TV back panel (section detail)
SERVICE
PORT
IEEE1394
INPUT/OUTPUT
DIGITAL
AUDIO
CableC ARD SLOT
ANT-2
AUX
ANT-1
MAIN
– (DTV/CABLE /VH F/UHF) –
1.
2.
Figure 4. Connecting separate UHF and VHF Antennas
Connecting a Single Analog Antenna or Separate UHF and
VHF Antennas
Single Antenna (not for use with CableCARD™)
Figure 3
A 300-Ohm to 75-Ohm transformer is required. This is not
included with the TV.
For antennas with twin flat lead
1. For antenna with twin flat leads, connect the
300-Ohm twin leads to the 300-Ohm to 75-Ohm
transformer.
2. Push the 75-Ohm side of the transformer onto ANT-1
MAIN on the TV back panel.
For antennas with coaxial lead
3. Connect the coaxial lead directly to ANT-1 MAIN on
the TV back panel.
SERVICE
PORT
IEEE1394
INPUT/OUTPUT
DIGITAL
AUDIO
CableCARD
TM SLOT
ANT-2
AUX
ANT-1
MAIN
– (DTV/CABLE /VHF/UHF) –
300-Ohm
FlatTwin
Lead
Optional 300-Ohm
to 75-Ohm
Matching Transformer
75-Ohm
Coaxial
Cable
TV back panel (section detail)
3.
2.
1.
Figure 3. Connecting an Antenna
Mitsubishi strongly recommends against using
antennas with twin flat leads. Twin flat lead
antenna wires are subject to interference which
may adversely affect the performance of the TV.
We recommend using coaxial antenna cable.

18
VCR to a Cable Box
Figure 6
A two-way RF splitter, 4 coaxial cables, right and left audio
cables and an S-Video or Video cable are required. These are
not included with the TV.
1. Connect the incoming cable to IN on the RF splitter.
2. Connect one coaxial cable from OUT on the RF
splitter to ANTENNA IN on the cable box back panel.
3. Connect one coaxial cable from OUT on the RF
splitter to ANT-2 AUX on the TV back panel.
4. Connect one coaxial cable from OUT on the cable
box to ANTENNA IN on the VCR back panel.
5. Connect one coaxial cable from ANTENNA OUT on
the VCR back panel to ANT-1 MAIN on the TV back
panel.
6. To use the TV speakers with the VCR, connect a
set of audio cables from AUDIO OUT on the VCR
back panel to INPUT 1 AUDIO-LEFT (MONO) and
AUDIO-RIGHT on the TV back panel. The red cable
connects to the R (right) channel and the white
Figure 6. Connecting a VCR to a Cable Box
TUBE
R
DIGITAL
SERVICE
PORT IEEE1394
INPUT/OUTPUT AUDIO
ANT-2
AUX
ANT-1
MAIN
CableCARD TM SLOT
– –(DTV/CABLE /VHF/UHF)
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
INPUT MONITOR OUTPUT
AUDIO 21 2
COMPONENT
YPbPr (480i/480p/1080i)
21
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DVI
Digital Video
Digital Audio
Analog Audio
S-Video
recommended
if available
Attach
only
one
cable
type
TV back panel
6.
5.
ANT-2
AUX
– –(DTV/CABLE /VHF/UHF)
7.
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
INPUT
1 2
ANT-1
MAIN
IN
OUT OUT
TWO WAYSPLITTER
Incoming Cable 1.
2.
3.
MONITOR OUTPUT
AUDIO/VIDEO 1
9.
3.
8.
Cable Box
back panel
section
IN OUT
2.
4.
9.
HS-U748
VCR back panel
If your VCR has a video channel
or RF ON/OFF switch, set it to OFF.
7.
6.
7. 8.
5.
4.
S-Video
recommended
if available
White
Red
White
Red
White
Red
W
h
i
t
e
R
e
d
Attach
only
one
cable
type
Note: NetCommand® will assume your VCR is connected to inputs as shown here. If you
use any other inputs for your VCR or add a second VCR this change must match in the
NetCommand system. See Edit NetCommand... pages 35-42 for more information.
Connecting VCR Video and Audio to a Cable Box
cable connects to the L (left) channel. If your VCR
is mono (non-stereo), connect only the white (left)
cable.
7. Connect either an S-Video or Video cable from
VIDEO OUT on the VCR back panel to INPUT 1
VIDEO on the TV back panel. Only one type of
video cable should be connected. S-Video is
recommended, if available.
8. For NetCommand® controlled recordings, connect
a Video cable from VIDEO IN on the VCR back
panel to MONITOR OUTPUT AUDIO/VIDEO 1 on
the TV back panel.
9. Complete the NetCommand controlled recording
connection by connecting a set of audio cables
from AUDIO IN on the VCR back panel to MONITOR
OUTPUT AUDIO/VIDEO 1 AUDIO-LEFT (MONO)
and AUDIO-RIGHT on the TV back panel. The red
cable connects to the R (right) channel and the
white cable connects to the L (left) channel.

19
For digital audio connections, see your
A/V Receiver, DVD and Satellite Receiver
Owner’s Guides.
IMPORTANT
A/V Receiver or Stereo System
Figure 7
A digital audio cable and stereo audio cables are required. The
digital audio cable is provided. The stereo audio cables are not
included with the TV.
1. Connect a set of stereo audio cables from OUTPUT
AUDIO 2 on the TV back panel to the TV AUDIO
INPUT on the back of the A/V Receiver. The red
cable connects to the R (right) channel and the
white cable connects to the L (left) channel.
To connect a digital A/V Receiver with Dolby®
Digital surround sound:
2. Connect one end of the digital audio cable supplied
with the TV to DIGITAL AUDIO on the back of the
TV. Connect the other end to the COAXIAL DIGITAL
INPUT on the back of the A/V Receiver.
Check A/V Receiver’s Owner’s Guide for information
concerning the use of the digital input and switching
between the digital sound and analog stereo sound
from the TV.
SERVICE WARNING
X-RAY PRECAUTION:
THISPRODUCT
I NC LU D E S CR IT IC A L ME C HA NI C AL
AND EL E CTRI CAL PAR TS WHI CH AR E
ES SENT IAL FOR X-R ADIAT ION SAFE TY.
F OR CO N TI NUE D S AF E TY R E P LA CE
C RIT IC A L COM PON E NT S I NDI CAT E D
IN THE SER VICE MA NUAL ONLY WI TH
E XAC T RE PLA CE ME NT PAR TS GI VE N
IN THE PARTS LIST. REFER TO SERVICE
MANUAL FOR OPERATING HIGH VOLTAGE AT
MINIMU M B RI GHT NE SS , MEASU RE ME NT
PR OCE DUR ES AN D PROP ER SE RV ICE
ADJUSTMENTS.
WARNING:
HANDLEWITH CARE. HIGH
VACUUM PICTURE TUBE IS DANGEROUS
TO HANDLE. REFE R SERV ICING TO
Q UAL IFI E D SE RV IC E P ER SO NNE L .
REPLACE WITH A TUBE OF THE SAME
TYPE NUMBER FOR CONTINUED SAFETY.
CAUTION:
TO MEASURE SECOND
ANODE VOLTAGE USE A HIGH VOLTAGE
METERCONNECTED FROM ANODE LEAD
TO CHASSIS ONLY. DISCHARGE HIGH
VOLTAGE TO CHASSIS ONLY, NOT TO
EXTERNALGROUND.
IR EMITTER
NetCommand R
DIGITAL
SERVICE
PORT
IEEE1394
INPUT/OUTPUT AUDIO
ANT-2
AUX
ANT-1
MAIN
CableCARD
TM SLOT
– –(DTV/CABLE /VHF/UHF)
S-VIDEO
VIDEO
INPUT
1 2
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
COMPONENT
YPbPr (480i/480p/1080i)
21
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DVI
Digital Video
Digital Audio
Analog Audio
IN IN I N IN IN IN I N INOUT OUT OUT OUT
AUX CD TAPE 1 TAPE 2 VCR 1 VCR2 TV DVD
MONITO R V CR 1 VC R 2 TV DVD
MONITO R V CR 1 VC R 2 TV DVD
OUT
OUT
IN
IN
IN
IN
IN
IN
IN
IN
OUT OUT
OUT OUT
CEN TER
SUB
WOOFE R
FRONTSUR.
REC
SOUR CE
LINE OUT
PRE OUT
SURROUND
SPEAKERS M IN.
FRONT
SPEAKERS-A MIN .
FRONT
SPEAKERS-B MIN.
CENTER
MIN.
L
L
L
LL
R
R
R
R
THIS DEVICE COMP LIES WITH PART15 OF THE
FCC RULES.OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE
MAYNOT CAUSE HARMFUL INTERFERENCE AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFER ENCE
RECEIVED, INCLUDING INTERFERENCE THATMAY
CAUSE UNDESIRED OPERATION.
MANUFACTUREDUNDER LICENSE FROM DOLBY LABORATORIE S LICENSING
CORPORATION. "DOLBY", "PRO LOGI C" AND THE DOUBLE-D SYMBO L ARE
TRADEMARKSOF DOLBY LABORATO RIES CO RPORATION.
COPYRIGHT1992 DOLBY LABORATORIE S, I NC. ALL RIGHTS
RESERVED
INPUT -1
(OPTICAL)
INPUT -2
(COAXIAL)
INPUT -3
(COAXIAL)
DIGITAL AUDIO
SWITCHED UNSWITCH ED
AC120V - 60Hz
TOTAL100W, 0.9A MAX
AC OUTLETS
MITSUBISHI
AUDIO/VIDEORECEIVER
MODELM-VR1000
POWERSUPPLY
POWERCONSUMPTION 120V-60Hz
552W,732VA
DISTRIBUTED BY
MITSUBISHICO NSU MER ELEC TRO NICS AMERICA
INC.
6100AT LAN TIC BLVD MADE IN
JAPAN
NORCRO SS, GA 30071 -1 3 05 FABRIQU E EN
JAPAN
!
AVIS
RISQUED E CHO C ELEC TRO NQ UE
NEPAS ENLEVER
RISKOF ELEC TR IC SHOC K
DONO T OPEN
ANTENNA
75
300
FM
AM
GND
ATUO
STANDBY
ON OFF
S-VI DEO
VIDE O
AUDI O
WARNIN G
A/V Receiver Rear Panel
Use only if
connecting
a Dolby Digital
A/V Receiver
DIGITAL
AUDIO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
MONITOR OUTPUT
AUDIO 2
2.
2.
1.
Red
White
Red
White
1.
TV back panel
AUDIO/VIDEO 1
Figure 7. Connecting an A/V Receiver
Connecting an A/V Receiver or Stereo System or
a Satellite Receiver or Other Device with S-Video
Satellite Receiver or Other Device with
S-Video
Figure 8
An S-Video cable and audio cables are required. These are not
included with the TV.
1. Connect an S-Video cable from VIDEO OUT on the
satellite receiver back panel to INPUT-2 VIDEO on
the TV back panel.
2. Connect a set of audio cables from AUDIO OUT on
the satellite receiver back panel to INPUT-2 AUDIO,
on the TV back panel. The red cable connects to
the R (right) channel and the white cable connects to
the L (left) channel.
Note: Refer to the Satellite Receiver Owner’s
Guide for Dish Antenna connections.
SERVICE WARNING
X-RAY PRECAUTION:
THISPRODUCT
I NCL U D ES C R I TI C AL ME C HA N I CAL
AN D ELEC TR ICAL PAR TS WHIC H ARE
ES SENTI AL FOR X-RA DIA TION SAFE TY.
F OR CO NTI NU E D SAF E TY RE P LAC E
CR IT I CA L COM PON EN TS I ND I CAT ED
IN THE SERV IC E MANU AL ONLY WIT H
E XACT R E PLAC E ME NT PART S GIV E N
IN THE PAR TS LIST. REFER TO SERVICE
MANUAL FOR OPERATI NG HIGH VOLTAGE AT
MIN IMUM BRI GHTNE SS, ME ASUREM ENT
PR OCED UR ES AND PR OP ER SER VI CE
ADJUSTMENTS.
WARNING:
HANDLE WITHCARE. HIGH
VACUUM PICTURE TUBE IS DANGEROUS
TO HANDLE. RE FER SE RVICING TO
QUA LI FIE D S E RV ICE P E R SONN E L.
REPLACE WITH A TUBE OF THE SAME
TYPE NUMBER FOR CONTINUED SAFETY.
CAUTION:
TO MEASURE SECOND
ANODE VOLTAGE USE A HIGH VOLTAGE
METER CONNECTEDFROM ANODE LEAD
TO CHASSIS ONLY. DISCHARGE HIGH
VOLTAGE TO CHASSIS ONLY, NOT TO
EXTERNAL GROUND.
IR EMITTER
NetCommand R
DIGITAL
SERVICE
PORT IEEE1394
INPUT/OUTPUT AUDIO
ANT-2
AUX
ANT-1
MAIN
CableCARDTM SLOT
– –(DTV/CABLE /VHF/UH F)
S-VIDEO
VIDEO
INPUT
1 2
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
COMPONENT
YPbPr (480i/480p/1080i)
21
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DVI
Digital Video
Digital Audio
Analog Audio
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
MONITOROUTPUT
AUDIO2
TV back panel
AUDIO/VIDEO 1
(Y/C)
L
R
L
R
1 2
VIDEO OU TAUDIO OUT AUDIO IN
Any S-Video Device
White
Red
1.
White
Red
1.
2.
2.
INPUT
1 2
Note: NetCommand® will asssume you
connected your Satellite Receiver to Input-2.
If you add a second Satellite Receiver or use
any other inputs for your Satellite Receiver,
this change must match in the NetCommand
system. See Edit NetCommand... pages 35-42
for more information.
Figure 8. Connecting a Satellite Receiver with S-Video

21
Connecting an HDMI Device or
External DTV Receiver with Component Video
See for component video signal Appendix B
compatibility information.
For digital audio connections, see your DTV
Receiver and A/V Receiver Owner’s Guides.
IMPORTANT
DTV Receiver (with YPrPb connections)
V
ID EO
Y
P
r
P
b
S-V ID EO
VCR
CONTROL
PHON EJA CK
RF
RE M
OTE
OUTTOTV
CH 3
CH 4
CAUTIO N
RI SK OF EL ECTRI CAL S HO CK
DO NOTOPEN
DIG IT AL
AUDIOOUT
White
Red
Incoming
Antenna
or Cable
SATELLITEININ FROM ANT
or
to antenna,
cable or satellite
AUDIO
L
R
A
UDI O
L
R
VID EO
SERVICEWA RNING
X-RAY PRECAUTION:
THIS PROD UCT
I NC L UD E S CR IT I C A L ME C H AN I C AL
AN D ELE CT RI CA L PAR TS WHI CH AR E
ES SE NTI AL FOR X -R AD IATION SAF ET Y.
F OR C ON T IN UE D S A FET Y R E PLA C E
CR I T IC AL C OM P ONE NT S I ND I CA TE D
IN THE SE RV ICE M ANU AL ONLY W ITH
E XA CT R EP LA CE ME NT PA R TS G IV EN
IN THE PARTS LIST. REFER TO SERV ICE
MANUAL FOR OPER ATING HIGH VOLTAGE AT
MIN IMU M BRI GHT NES S, M EAS URE ME NT
PR OC ED URE S AN D P RO PE R SE RV ICE
ADJUSTM ENTS.
WARNING:
HANDLE W ITH CARE. H IGH
VACUUM PICTU RE TUBE IS D ANGEROUS
TO HANDL E. RE FER SER VICI NG TO
QU A LI FIE D SE R VI CE PE R SO NN EL .
REPLAC E WITH A TUB E OF THE SAME
TYPE NU MBER FOR C ONTINUED SA FETY.
CAUTION:
TO MEAS URE SECON D
ANODE VOLTAGE U SE A HIGH VOLTAGE
METER C ONNECTED FR OM ANODE LEAD
TO CHASSIS ON LY. DISCHAR GE HIGH
VOLTAGE TO CHASSIS ONLY, NOT TO
EXTER NAL GROUND .
IR EMITTE R
NetCommand
R
DIGITAL
SERVICE
PORT IEEE1394
INPUT/ OUTPUT AUD IO
ANT-2
AUX
ANT-1
MAIN
CableCARD
TM
SLOT
– –(DT V/CABLE / VHF/ UHF )
S-VIDE O
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
INPUT MONITOR OUTPUT
AUDIO 2
AUDIO/VIDEO 1
1 2
COMPONE NT
YPbPr (480i/480p/1080i)
21
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DVI
DigitalVideo
DigitalAudio
AnalogAudio
ANT-1
MAIN
– –(DT V/CABLE / VHF/ UHF )
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
COMPONE NT
YPbPr (480i/480p/1080i )
21
White
Red
1.
1.
2.
2.
3.
3.
4.
4.
Figure 12. Connecting an External DTV Receiver with
Component Video Connections
External DTV Receiver with
Component Video
Figure 12
A coaxial splitter, RCA video cables and audio cables are
required. These are not included with the TV.
1. Connect the outside antenna, cable or satellite to
ANT or SATELLITE IN on the DTV receiver (see your
DTV receiver’s owner’s guide for instructions and
cable compatibility).
2. Connect the incoming terrestrial antenna or cable
(not satellite) to ANT-1 on the TV back panel
(a coaxial splitter, available at most electronic
supply stores, may be required to complete this
installation).
3. Connect RCA-type cables from the YPrPb outputs
on the DTV receiver to either Component 1 or
2 on the TV back panel, matching the correct
connections:
DTV Receiver to TV Back panel
• to YY
• to PrPr
• to PbPb
4. Connect the L (left) and R (right) audio cables from
the DTV receiver to Component 1 or 2 AUDIO LEFT
and AUDIO RIGHT on the TV back panel. If you
connected the YPrPb outputs to Component 1, also
use Component 1 to connect the audio cable. The
red cable connects to the R (right) channel and the
white cable connects to the L (left) channel.
Note: To utilize the benefits of a digital A/V
receiver, connect your DTV receiver’s digital
audio out to a digital input on your digital A/V
receiver.
SERVICE WARNING
X-RAYPRECAUTION:
THIS PRODUCT
I NC L U D E S C R ITI C A L ME C H A N IC A L
AN D ELE CT RI CA L PART S WHI CH AR E
ES SE NTI AL FOR X-RAD IAT ION SA FE TY.
F OR C ON T IN U ED S A FET Y R EP L AC E
CR I T IC A L COMP ON E NT S I N DI C AT ED
IN THE S ERVIC E MANUA L ONLY WITH
E XA CT R EP LA CE MEN T PAR TS G IV E N
IN THE PARTS LIST. REFER TO SERVICE
MANUAL FOR OPERATING HIGH VOLTAGE AT
MIN IMUM BRI GHT NES S, MEA SUR EME NT
PR OC ED UR ES AND PRO PE R SE RV IC E
ADJUSTMENTS.
WARNING:
HANDLE WITH CARE. HIGH
VACUUM PICTURE TUBE IS DANGEROUS
TO HANDL E. RE FER SE RVI CING TO
QU A LI FI E D SE R V ICE PE R S ON NE L .
REPLACE WITH A TUBE OF THE SAME
TYPE NUMBER FOR CONTINUED SAFETY.
CAUTION:
TO MEASURE SECOND
ANODE VOLTAGE USE A HIGH VOLTAGE
METER CONNECTED FROM ANODE LEAD
TO CHASSIS ONLY. DISCHARGE HIGH
VOLTAGE TO CHASSIS ONLY, NOT TO
EXTERNAL GROUND.
IR EMITTER
NetCommand R
DIGITAL
SERVICE
PORT IEEE1394
INPUT/OU TPUT AUDIO
ANT-2
AUX
ANT-1
MAIN
CableCARD TM SLOT
– –(DTV /CABLE /VHF /UHF)
S-VIDEO
VIDEO
INPUT
1 2
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
COMPONENT
YPbPr (480i/480p/1080i)
21
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DVI
Digital Video
Digital Audio
Analog Audio
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
MONITOR OUTPUT
AUDIO 2
TV back panel
AUDIO/VIDEO1
Digital Video
Digital Audio
HD-6000 Receiver
Figure 11. Connecting an HDMI Device
HDMI Device
Figure 11
An HDMI-to-HDMI cable is required. This is not included with
the TV. It may be available at your local electronics retailer
Connect an HDMI cable from the TV back panel to the
HDMI device output. HDMI devices provide video and
audio through this cable, so no other connection is
required.

22
Connecting the IR Emitter NetCommand ®
DI GI TA L
SU RRO UN D
S
CH
IR EMITTER
NetCommand R
TV back panel
(section detail)
A/V Receiver
Other A/V device
Other A/V device
1. 6.
4.
3.
3.
2.
Figure 13. Connecting IR Emitter NetCommand
IR Emitter NetCommand ®
Figure 13
A quadruple IR Emitter cable is included with the TV.
The emitters connected to these jacks are used by the
NetCommand system to control other devices such as
VCR, DVD players, Cable boxes and Satellite receivers.
1. Connect the plug end of the supplied quadruple IR
Emitter Cable to one of the IR Output NetCommand
jacks on the TV back panel.
2. Run the cable for each of the emitter ends under,
along side or over the top of each device to be
controlled to the area of the front where the remote
control sensor is located.
3. Place the emitter end in front of the remote control
sensor of the device to be controlled. The emitter
bulb should face the remote control sensor. This
bulb emits infrared light in a cone shaped pattern.
The bulb needs to be placed far enough from the
remote control sensor to allow the cone pattern to
include the sensor.
The remote control sensor is usually behind the plastic
window of the front display panel. It is sometimes
visible when you look through the display plastic using
a flashlight and is normally a round or square cutout
behind the plastic. If you cannot see the sensor and
the device’s Owner’s Guide does not specify the
If a single emitter end can be placed in a
position that will operate more than one device,
do not use a separate emitter end for the
additional device. A single device receiving
remote control signals from too many emitters
or remote controls may not respond at all.
IMPORTANT
location, you can find it by using the device’s remote
control. Hold the remote about 1/2 inch from the front
of the device. Starting from one end of the display
window plastic, press the POWER button.
If the device does not respond, move the remote
control 1 inch toward the center and try again. Repeat
this until the device responds. Note this location then
start over from the other end of the display window
plastic, repeating until the device responds again. The
remote control sensor will be somewhere between
these two positions. This is usually enough accuracy
for the placement of the IR emitters.
4. With some devices, the emitter will work better
facing downward from the top of the device. Some
experimentation may be needed. If you are not
going to be using all emitter ends, place the unused
ends behind the devices so that they cannot send
signals to the remote control sensors.
5. The emitter end being used can be secured in place
using double stick tape.
6. Place any unused emitters in an out-of-the-way
location.

23
Connecting IEEE 1394 Devices
4-Pin Style vs. 6-Pin Style
There are two different types of connectors used for
IEEE 1394 terminals and cables, a 4-pin and a 6-pin
style.
The 4-pin connector sends
digital audio signals, digital video
signals and digital control signals
back and forth between devices.
Your TV has two or three 4-pin
type connection jacks available.
All models have two inputs
on the back panel. WS-55615,
WS-55615A. WS-65615.
WS-65615A and WS-73615 have
an additional input on the front
panel.
The 6-pin connector is capable
of sending the same digital audio,
video and control signals as the
4-pin connector, but the 6-pin
connector is also able to send low
voltage electrical power. This TV
does not have 6 pin connectors.
The purpose of this low voltage electrical power is
to provide operating power to a device that is not
connected directly to the household AC power such
as a camcorder. A device with a 6-pin connector can
send this electrical power to another device, or receive
electrical power from another device, or simply use a
6-pin connector without using the two additional pins.
A 6-pin connector cannot be
connected directly to a 4-pin
jack, and vice versa. Instead,
you will need to obtain a 6-pin to
4-pin adaptor or adaptor cable.
These cables are available from
electronic and computer stores.
If you connect a 6-pin device to the TV (such as a
camcorder) that is designed to receive electrical power
from another 6-pin device, you will need to connect
the camcorder directly to the household AC, or use the
camcorder’s battery for power. If this is not possible,
then the camcorder will need to be connected directly
to another 6-pin device in the network that can provide
the electrical power.
6 pin to 4 pin adaptor
4 pin connector
6 pin connector
When Connecting IEEE 1394 Devices
• Do not loop the last device in the chain back to
the TV. When the device chain is looped, the TV
may not be able to work with the other devices.
• Place devices that have only a mechanical (two-
position) power switch at the end of the chain or
leave the power switch in the On position. When
turned Off, IEEE 1394 signals may not be able to
pass through the device to other devices.
• Place devices with the slowest communication
speed at the end of the chain. Sometimes the
communication speed will be marked near the
IEEE 1394 connector with an “S” number. The
higher the number, the faster the communication
speed. Devices with slow communication speed
can interfere with IEEE 1394 signals from faster
devices. When using NetCommand to set up
a digital recording between a faster and slower
device, select “Record Later”.
• Do not use an IEEE 1394 cable longer than 15
feet between each device.
• This TV is an IEEE 1394a Device. IEEE 1394b
is currently under development. This system
will provide for longer distances and multi-
room applications. Included in the IEEE
1394b systems are IEEE 1394a to IEEE 1394b
converters to maintain compatibility with this TV
and other IEEE 1394a devices.
Specyfikacje produktu
Marka: | Mitsubishi |
Kategoria: | Telewizja |
Model: | WS-73615 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Mitsubishi WS-73615, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Telewizja Mitsubishi

13 Października 2024

29 Września 2024

22 Września 2024

21 Września 2024

17 Września 2024

14 Września 2024

13 Września 2024

13 Września 2024

12 Września 2024

12 Września 2024
Instrukcje Telewizja
- Telewizja Sony
- Telewizja Yamaha
- Telewizja Samsung
- Telewizja Electrolux
- Telewizja AEG
- Telewizja Beko
- Telewizja LG
- Telewizja Küppersbusch
- Telewizja Xiaomi
- Telewizja Sharp
- Telewizja TCL
- Telewizja Pioneer
- Telewizja Lenovo
- Telewizja Philips
- Telewizja SilverCrest
- Telewizja Acer
- Telewizja Nokia
- Telewizja Hisense
- Telewizja Infiniton
- Telewizja Panasonic
- Telewizja Muse
- Telewizja Viewsonic
- Telewizja Nedis
- Telewizja AG Neovo
- Telewizja Medion
- Telewizja OK
- Telewizja Lenco
- Telewizja Polar
- Telewizja Marquant
- Telewizja Toshiba
- Telewizja Tesla
- Telewizja Westinghouse
- Telewizja Majestic
- Telewizja Jensen
- Telewizja ILive
- Telewizja Blaupunkt
- Telewizja Brandt
- Telewizja Vivax
- Telewizja Terris
- Telewizja Salora
- Telewizja Siemens
- Telewizja Teac
- Telewizja Casio
- Telewizja Iiyama
- Telewizja Citizen
- Telewizja Dual
- Telewizja Grundig
- Telewizja Haier
- Telewizja Soundmaster
- Telewizja Hyundai
- Telewizja Manhattan
- Telewizja Strong
- Telewizja ECG
- Telewizja Oyster
- Telewizja Icy Box
- Telewizja Bang & Olufsen
- Telewizja JVC
- Telewizja V7
- Telewizja Dell
- Telewizja Furrion
- Telewizja Funai
- Telewizja Oppo
- Telewizja TechniSat
- Telewizja Schneider
- Telewizja Krüger&Matz
- Telewizja Philco
- Telewizja CHiQ
- Telewizja Qilive
- Telewizja Uniden
- Telewizja Thomson
- Telewizja Ferguson
- Telewizja Wharfedale
- Telewizja Manta
- Telewizja Pyle
- Telewizja Cecotec
- Telewizja Marantz
- Telewizja AOC
- Telewizja Monster
- Telewizja Peerless-AV
- Telewizja Caratec
- Telewizja Nevir
- Telewizja Arçelik
- Telewizja Continental Edison
- Telewizja GoGen
- Telewizja Intenso
- Telewizja NEC
- Telewizja Polaroid
- Telewizja Aiwa
- Telewizja AKAI
- Telewizja Sanyo
- Telewizja Clatronic
- Telewizja Telefunken
- Telewizja Optoma
- Telewizja SVAN
- Telewizja Innoliving
- Telewizja Abus
- Telewizja Jay-Tech
- Telewizja Bush
- Telewizja Loewe
- Telewizja Kemo
- Telewizja VOX
- Telewizja Insignia
- Telewizja AYA
- Telewizja Element
- Telewizja Orima
- Telewizja Denver
- Telewizja Kernau
- Telewizja Aspes
- Telewizja Albrecht
- Telewizja Orion
- Telewizja Hitachi
- Telewizja Technika
- Telewizja Seiki
- Telewizja SereneLife
- Telewizja RCA
- Telewizja MBM
- Telewizja BenQ
- Telewizja Trevi
- Telewizja Lexibook
- Telewizja GPX
- Telewizja Sencor
- Telewizja Odys
- Telewizja Nabo
- Telewizja Nextbase
- Telewizja Zenith
- Telewizja Daewoo
- Telewizja Allview
- Telewizja Metz
- Telewizja Kunft
- Telewizja Grunkel
- Telewizja Alphatronics
- Telewizja XD Enjoy
- Telewizja RevolutionHD
- Telewizja FFalcon
- Telewizja Dyon
- Telewizja Reflexion
- Telewizja Megasat
- Telewizja Sogo
- Telewizja Proline
- Telewizja Finlux
- Telewizja Alden
- Telewizja Aldi
- Telewizja Airis
- Telewizja Aristona
- Telewizja Apex
- Telewizja Ziggo
- Telewizja Techwood
- Telewizja Walker
- Telewizja Saba
- Telewizja Antarion
- Telewizja Tevion
- Telewizja Proscan
- Telewizja Vestel
- Telewizja Tucson
- Telewizja Energy Sistem
- Telewizja Sagem
- Telewizja Sunstech
- Telewizja Sylvania
- Telewizja Sunny
- Telewizja Luxor
- Telewizja Nordmende
- Telewizja AudioAffairs
- Telewizja Magnum
- Telewizja Audiosonic
- Telewizja Kubo
- Telewizja Coby
- Telewizja Seg
- Telewizja Vivo
- Telewizja Daitsu
- Telewizja Changhong
- Telewizja Alba
- Telewizja Naxa
- Telewizja Star-Light
- Telewizja Fantec
- Telewizja Mpman
- Telewizja Sweex
- Telewizja Vizio
- Telewizja Cello
- Telewizja Mx Onda
- Telewizja Nikkei
- Telewizja Peaq
- Telewizja Hannspree
- Telewizja DGM
- Telewizja Yasin
- Telewizja Roadstar
- Telewizja Humax
- Telewizja MT Logic
- Telewizja Superior
- Telewizja Difrnce
- Telewizja ITT
- Telewizja Avtex
- Telewizja Inovia
- Telewizja Lin
- Telewizja Aconatic
- Telewizja NPG
- Telewizja Bluesky
- Telewizja Videocon
- Telewizja Xoro
- Telewizja Durabase
- Telewizja HKC
- Telewizja Edenwood
- Telewizja Woxter
- Telewizja Premier
- Telewizja Onn
- Telewizja Teleco
- Telewizja Packard Bell
- Telewizja Opera
- Telewizja LTC
- Telewizja JTC
- Telewizja Zalman
- Telewizja Horizon
- Telewizja United
- Telewizja SYLVOX
- Telewizja Doffler
- Telewizja FOX Electronics
- Telewizja Viewpia
- Telewizja JGC
- Telewizja Online
- Telewizja DirecTV
- Telewizja Tele 2
- Telewizja Graetz
- Telewizja Kogan
- Telewizja Telesystem
- Telewizja EKO
- Telewizja E-motion
- Telewizja Mitsai
- Telewizja Selfsat
- Telewizja High One
- Telewizja Tve
- Telewizja ISymphony
- Telewizja Pantel
- Telewizja Magnavox
- Telewizja ATYME
- Telewizja HCI
- Telewizja Inno-Hit
- Telewizja Engel
- Telewizja TechLine
- Telewizja Elements
- Telewizja Digihome
- Telewizja Englaon
- Telewizja Reflex
- Telewizja Astar
- Telewizja Visco
- Telewizja Tivax
- Telewizja H&B
- Telewizja Norcent
- Telewizja TELE System
- Telewizja TIM
- Telewizja Belson
- Telewizja Vision Plus
- Telewizja Sbr
- Telewizja Bauhn
- Telewizja Voxx
- Telewizja Rm 2000
- Telewizja Hoher
- Telewizja Felson
- Telewizja Mach Power
- Telewizja Elbe
- Telewizja Axing
- Telewizja CGV
- Telewizja Smart Tech
- Telewizja Séura
- Telewizja Mitzu
- Telewizja JTC24
- Telewizja Coocaa
- Telewizja Kivi
- Telewizja Smart Brand
- Telewizja Mystery
- Telewizja Linsar
Najnowsze instrukcje dla Telewizja

27 Marca 2025

26 Marca 2025

19 Marca 2025

19 Marca 2025

12 Marca 2025

12 Marca 2025

12 Marca 2025

12 Marca 2025

12 Marca 2025

12 Marca 2025