Instrukcja obsługi Milwaukee 6089-31

Milwaukee szlifierka 6089-31

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Milwaukee 6089-31 (36 stron) w kategorii szlifierka. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/36

Cat. No.

No de Cat.

6088-30

6088-31

6089-30

6089-31

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

TO REDUCE THE RISK OF INJURY, USER MUST READ OPERATOR'S MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER EL MANUAL DEL OPERADOR.

HEAVY-DUTY SANDERS AND GRINDERS

PONCEUSES-RECTIFIEUSES EXTRA ROBUSTES

LIJADORAS Y ESMERILADORAS HEAVY-DUTY

page 2

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

PERSONAL SAFETY

POWER TOOL USE AND CARE

SERVICE

WARNING

READ ALL SAFETY WARNINGS AND INSTRUCTIONS.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference

The term "power tool" in all of the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

SPECIFIC SAFETY RULES

• Keep work area clean and well lit. Cluttered or dark areas invite ac-

cidents.

• Do not operate power tools in explosive atmospheres, such as in

the presence of ﬂ ammable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

• Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

• Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets will reduce risk of electric

shock.

• Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions. Water entering

a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled cords increase the risk

of electric shock.

• When operating a power tool outdoors, use an extension cord suit-

able for outdoor use. Use of a cord suitable for outdoor use reduces the

risk of electric shock.

• If operating a power tool in a damp location is unavoidable, use a

residual current device (RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

• Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in serious personal

injury.

• Use personal protective equipment. Always wear eye protection.

Protective equipment such as dust mask, non-skid safety shoes, hard hat,

or hearing protection used for appropriate conditions will reduce personal

injuries.

• Prevent unintentional starting. Ensure the switch is in the off-position

before connecting to power source and/or battery pack, picking up

or carrying the tool. Carrying power tools with your ﬁ nger on the switch

or plugging in power tools that have the switch on invites accidents.

• Remove any adjusting key or wrench before turning the power tool

on. A wrench or a key left attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewellery. Keep your

hair, clothing and gloves away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving parts.

• If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used.

Use of these devices can reduce dust-related hazards.

• Do not force the power tool. Use the correct power tool for your ap-

plication. The correct power tool will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the switch does not turn it on and oﬀ.

Any power tool that cannot be controlled with the switch is dangerous and

must be repaired.

• Disconnect the plug from the power source and/or the battery pack

from the power tool before making any adjustments, changing ac-

cessories, or storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of children and do not allow

persons unfamiliar with the power tool or these instructions to oper-

ate the power tool. Power tools are dangerous in the hands of untrained

users.

• Maintain power tools. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may aﬀect the

power tool operation. If damaged, have the power tool repaired before

use. Many accidents are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained cutting tools

with sharp cutting edges are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc., in accordance with

these instructions, taking into account the working conditions and

the work to be performed. Use of the power tool for operations diﬀerent

from those intended could result in a hazardous situation.

• Have your power tool serviced by a qualiﬁ ed repair person using only

identical replacement parts. This will ensure that the safety of the power

tool is maintained.

Safety Warnings Common for Grinding, Sanding, Wire Brushing or

Abrasive Cutting-Oﬀ Operations:

• This power tool is intended to function as a grinder, sander, wire

brush or cut-of tool. Read all safety warnings, instructions, illus-

trations and speciﬁ cations provided with this power tool. Failure to

follow all instructions listed below may result in electric shock, ﬁ re and/or

serious injury.

• Operations such as polishing are not recommended to be performed

with this power tool. Operations for which the power tool was not de-

signed may create a hazard and cause personal injury.

• Do not use accessories which are not speciﬁ cally designed and

recommended by the tool manufacturer. Just because the accessory

can be attached to your power tool, it does not assure safe operation.

• The rated speed of the accessory must be at least equal to the

maximum speed marked on the power tool. Accessories running faster

than their rated speed can break and ﬂ y apart.

• The outside diameter and the thickness of your accessory must

be within the capacity rating of your power tool. Incorrectly sized

accessories cannot be adequately guarded or controlled.

• The arbour size of wheels, ﬂ anges, backing pads or any other acces-

sory must properly ﬁ t the spindle of the power tool. Accessories with

arbour holes that do not match the mounting hardware of the power tool will

run out of balance, vibrate excessively and may cause loss of control.

• Do not use a damaged accessory. Before each use inspect the

accessory such as abrasive wheels for chips and cracks, backing

pad for cracks, tear or excess wear, wire brush for loose or cracked

wires. If power tool or accessory is dropped, inspect for damage or

page 3

install an undamaged accessory. After inspecting and installing an

accessory, position yourself and bystanders away from the plane of

the rotating accessory and run the power tool at maximum no-load

speed for one minute. Damaged accessories will normally break apart

during this test time.

• Wear personal protective equipment. Depending on application,

use face shield, safety goggles or safety glasses. As appropriate,

wear dust mask, hearing protectors, gloves and work shop apron

capable of stopping small abrasive or workpiece fragments. The

eye protection must be capable of stopping ﬂ ying debris generated

by various operations. The dust mask or respirator must be capable of

ﬁ ltrating particles generated by your operation. Prolonged exposure to

high intensity noise may cause hearing loss.

• Keep bystanders a safe distance away from work area. Anyone

entering the work area must wear personal protective equipment.

Fragments of workpiece or of a broken accessory may ﬂ y away and cause

injury beyond immediate area of operation.

• Hold power tool by insulated gripping surfaces only, when perform-

ing an operation where the cutting accessory may contact hidden

wiring or its own cord. Cutting accessory contacting a live wire may

make exposed metal parts of the power tool live and shock the opera-

tor.

• Position the cord clear of the spinning accessory. If you lose control,

the cord may be cut or snagged and your hand or arm may be pulled into

the spinning accessory.

• Never lay the power tool down until the accessory has come to a

complete stop. The spinning accessory may grab the surface and pull

the power tool out of your control.

• Accidental Do not run the power tool while carrying it at your side.

contact with the spinning accessory could snag your clothing, pulling the

accessory into your body.

• Regularly clean the power tool’s air vents. The motor’s fan will draw

the dust inside the housing and excessive accumulation of powdered

metal may cause electrical hazards.

• Do not operate the power tool near ﬂ ammable materials. Sparks could

ignite these materials.

• Do not use accessories that require liquid coolants. Using water or

other liquid coolants may result in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating wheel,

backing pad, brush or any other accessory. Pinching or snagging causes

rapid stalling of the rotating accessory which in turn causes the uncon-

trolled power tool to be forced in the direction opposite of the accessory’s

rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by the work-

piece, the edge of the wheel that is entering into the pinch point can dig

into the surface of the material causing the wheel to climb out or kick out.

The wheel may either jump toward or away from the operator, depending

on direction of the wheel’s movement at the point of pinching. Abrasive

wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper precau-

tions as given below.

• Maintain a ﬁ rm grip on the power tool and position your body and

arm to allow you to resist kickback forces. Always use auxiliary

handle, if provided, for maximum control over kickback or torque

reaction during start-up. The operator can control torque reactions or

kickback forces, if proper precautions are taken.

• Never place your hand near the rotating accessory. Accessory may

kick back over your hand.

• Do not position your body in the area where power tool will move

if kickback occurs. Kickback will propel the tool in direction opposite to

the wheel’s movement at the point of snagging.

• Use special care when working corners, sharp edges etc. Avoid

bouncing and snagging the accessory. Corners, sharp edges or

bouncing have a tendency to snag the rotating accessory and cause loss

of control or kickback.

• Do not attach a saw chain woodcarving blade or toothed saw blade.

Such blades create frequent kickback and loss of control.

Safety Warnings Specific for Grinding and Abrasive Cutting-Off

Operations:

• Use only wheel types that are recommended for your power tool

and the speciﬁ c guard designed for the selected wheel. Wheels for

which the power tool was not designed can not be adequately guarded

and are unsafe.

• The guard must be securely attached to the power tool and posi-

tioned for maximum safety, so the least amount of wheel is exposed

towards the operator. The guard helps to protect operator from broken

wheel fragments and accidental contact with wheel.

• Wheels must be used only for recommended applications. For ex-

ample: do not grind with the side of cut-oﬀ wheel.

Abrasive cut-oﬀ

wheels are intended for peripheral grinding, side forces applied to these

wheels may cause them to shatter.

• Always use undamaged wheel ﬂ anges that are of correct size and

shape for your selected wheel. Proper wheel ﬂ anges support the wheel

thus reducing the possibility of wheel breakage. Flanges for cut-off wheels

may be diﬀerent from grinding wheel ﬂ anges.

• Do not use worn down wheels from larger power tools. Wheel

intended for larger power tool is not suitable for the higher speed of a

smaller tool and may burst.

Additional Safety Warnings Speciﬁ c for Abrasive Cutting-Oﬀ Opera-

tions:

• Do not jam the cut-oﬀ wheel or apply excessive pressure. Do not

attempt to make an excessive depth of cut. Overstressing the wheel

increases the loading and susceptibility to twisting or binding of the wheel

in the cut and the possibility of kickback or wheel breakage.

• Do not position your body in line with and behind the rotating wheel.

When the wheel, at the point of operation, is moving away from your body,

the possible kickback may propel the spinning wheel and the power tool

directly at you.

• When wheel is binding or when interrupting a cut for any reason,

switch off the power tool and hold the power tool motionless until the

wheel comes to a complete stop. Never attempt to remove the cut-off

wheel from the cut while the wheel is in motion otherwise kickback

may occur. Investigate and take corrective action to eliminate the cause

of wheel binding.

• Do not restart the cutting operation in the workpiece. Let the wheel

reach full speed and carefully reenter the cut. The wheel may bind,

walk up or kickback if the power tool is restarted in the workpiece.

• Support panels or any oversized workpiece to minimize the risk of

wheel pinching and kickback. Large workpieces tend to sag under their

own weight. Supports must be placed under the workpiece near the line

of cut and near the edge of the workpiece on both sides of the wheel.

• Use extra caution when making a “pocketcut” into existing walls

or other blind areas. The protruding wheel may cut gas or water pipes,

electrical wiring or objects that can cause kickback.

Safety Warnings Speciﬁ c for Sanding Operations:

• Do not use excessively oversized sanding disc paper. Follow manu-

facturers recommendations, when selecting sanding paper. Larger

sanding paper extending beyond the sanding pad presents a laceration

hazard and may cause snagging, tearing of the disc or kickback.

Safety Warnings Speciﬁ c for Wire Brushing Operations:

• Be aware that wire bristles are thrown by the brush even during or-

dinary operation. Do not over stress the wires by applying excessive

load to the brush. The wire bristles can easily penetrate light clothing

and/or skin.

• If the use of a guard is recommended for wire brushing, do not al-

low any interference of the wire wheel or brush with the guard. Wire

wheel or brush may expand in diameter due to workload and centrifugal

forces.

Additional Safety Warnings

• Maintain labels and nameplates. These carry important information. If

unreadable or missing, contact a MILWAUKEE service facility for a free

replacement.

• WARNING: Some dust created by power sanding, sawing, grinding,

drilling, and other construction activities contains chemicals known to

cause cancer, birth defects or other reproductive harm. Some examples

of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other masonry products,

and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do

this type of work. To reduce your exposure to these chemicals: work in

a well ventilated area, and work with approved safety equipment, such

as those dust masks that are specially designed to ﬁ lter out microscopic

particles.

Specyfikacje produktu

Marka:	Milwaukee
Kategoria:	szlifierka
Model:	6089-31

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Milwaukee 6089-31, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje szlifierka Milwaukee

Milwaukee 2781-21 Instrukcja

8 Października 2024

Milwaukee 0725-21 Instrukcja

5 Października 2024

Milwaukee HD18 AG115 Instrukcja

4 Października 2024

Milwaukee AG 9-125 XE Instrukcja

4 Października 2024

Milwaukee AGV 21-230 GEX Instrukcja

4 Października 2024

Milwaukee HD18 AG125 Instrukcja

4 Października 2024

Milwaukee DGL 34 Instrukcja

3 Października 2024

Milwaukee DG 30 E Instrukcja

3 Października 2024

Milwaukee 2784-20 Instrukcja

3 Października 2024

Milwaukee AGV 17-180 XC DMS Instrukcja

2 Października 2024

Instrukcje szlifierka

Najnowsze instrukcje dla szlifierka

HiKOKI GP2S2 Instrukcja

15 Października 2024

Makita GA9060R Instrukcja

14 Października 2024

Hitachi G 13SR Instrukcja

14 Października 2024

Makita DGA700Z Instrukcja

12 Października 2024

Einhell NBG 150 Instrukcja

9 Października 2024

Einhell TE-AG 18/100 Li-Solo Instrukcja

9 Października 2024

Einhell TC-AG 100 Instrukcja

9 Października 2024

Einhell MWS 115/2 Instrukcja

9 Października 2024

Einhell Professional TP-AG 2320 Instrukcja

9 Października 2024

Einhell RT-AG 230/180 Instrukcja

9 Października 2024