Instrukcja obsługi Milwaukee 5387-22

Milwaukee Wiertarka 5387-22

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Milwaukee 5387-22 (13 stron) w kategorii Wiertarka. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/13

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

Cat. No.

No de cat.

5381-20

5387-20

1/2" HAMMER-DRILL

PERCEUSES À PERCUSSION 13 mm (1/2")

13 mm (1/2") TALADRO-MARTILLO

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

SPECIFICATIONS

Capacities

Tool Drill Only

(steel/wood)

Rotary Hammer

(concrete)

Cat. No. Volts

AC Amps No Load

RPM

No Load Blows

per Minute Twist Drill Bit Carbide Tipped

Percussion Bit

5387-20

5381-20

120

8.5

Low 0 - 1000

High 0 - 2500

0 - 1800

16,000

40,000

28,000

1/2" / 1"

3/8" / 3/4"

3/4"

5/8"

SYMBOLOGY

Double Insulated

Amperes

Volts

Alternating Current

No Load Revolutions

per Minute (RPM)

BPM Blows per Minute (BPM)

C US Underwriters Laboratories, Inc.

United States and Canada

Mexican Approvals Marking

FUNCTIONAL DESCRIPTION

1. Side handle

2. Clamping lever

3. Depth guage

4. Hammer/Drill lever

5. Variable speed trigger

6. Forward/Reverse lever

7. Speed/Torque selector(Cat. No. 5387-20 only)

8. Chuck

9. Quik-Lok® cord (Cat. No. 5387-20 only)

Cat. No. 5387-20

7 6 5

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive atmos-

pheres, such as in the presence of ﬂ ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase

the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk

of electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit inter-

rupter (GFCI) protected supply. Use of an GFCI

reduces the risk of electric shock.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

• Do not force the power tool. Use the correct

power tool for your application. The correct

WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. Failure

to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious

injury. Save all warnings and instructions for future reference. The term "power

tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

POWER TOOL USE AND CARE

power tool will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the switch does not

turn it on and o. Any power tool that cannot be

controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such pre-

ventive safety measures reduce the risk of starting

the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

for operations dierent from those intended could

result in a hazardous situation.

• Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inﬂ uence of drugs, alcohol or medi-

cation. A moment of inattention while operating

power tools may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your ﬁ nger on the switch or energising power tools

that have the switch on invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

SERVICE

• Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

SPECIFIC SAFETY RULES

• Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its

own cord. Cutting accessory contacting a “live”

wire may make exposed metal parts of the power

tool “live” and could give the operator an electric

shock.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• WARNING Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and

other masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to ﬁ lter out microscopic particles.

• Wear ear protectors when impact drilling.

Exposure to noise can cause hearing loss.

•

Use auxiliary handle(s), if supplied with the

tool. Loss of control can cause personal injury.

Grounded Tools: Tools with Three Prong Plugs

Tools marked “Grounding Required” have a three

wire cord and three prong grounding plug. The

plug must be connected to a properly grounded

outlet (See Figure A). If the tool should electrically

malfunction or break down, grounding provides a

low resistance path to carry electricity away from

the user, reducing the risk of electric shock.

The grounding prong in the plug is connected

through the green wire inside the cord to the

grounding system in the tool. The green wire in the

cord must be the only wire connected to the tool's

grounding system and must never be attached to

an electrically “live” terminal.

Your tool must be plugged into

an appropriate outlet, properly

installed and grounded in ac-

cordance with all codes and

ordinances. The plug and outlet

should look like those in Figure A.

Double Insulated Tools:

Tools with Two Prong Plugs

Tools marked “Double Insulated” do not require

grounding. They have a special double insula-

tion system which satisﬁ es OSHA requirements

and complies with the applicable standards of

Underwriters Laboratories, Inc.,

the Canadian Standard Asso-

ciation and the National Elec-

trical Code. Double Insulated

tools may be used in either of

the 120 volt outlets shown in

Figures B and C.

Fig. A

GROUNDING

WARNING Improperly connecting the

grounding wire can result in the risk of elec-

tric shock. Check with a qualiﬁ ed electrician

if you are in doubt as to whether the outlet is

properly grounded. Do not modify the plug

provided with the tool. Never remove the

grounding prong from the plug. Do not use

the tool if the cord or plug is damaged. If

damaged, have it repaired by a MILWAUKEE

service facility before use. If the plug will not

ﬁ t the outlet, have a proper outlet installed by

a qualiﬁ ed electrician.

Grounded tools require a three wire extension

cord. Double insulated tools can use either a two

or three wire extension cord. As the distance from

the supply outlet increases, you must use a heavier

gauge extension cord. Using extension cords with

inadequately sized wire causes a serious drop in

voltage, resulting in loss of power and possible tool

damage. Refer to the table shown to determine the

required minimum wire size.

The smaller the gauge number of the wire, the

greater the capacity of the cord. For example, a 14

gauge cord can carry a higher current than a 16

gauge cord. When using more than one extension

cord to make up the total length, be sure each cord

contains at least the minimum wire size required.

If you are using one extension cord for more than

one tool, add the nameplate amperes and use the

sum to determine the required minimum wire size.

Guidelines for Using Extension Cords

• If you are using an extension cord outdoors, be sure

it is marked with the sufﬁ x “W-A” (“W” in Canada)

to indicate that it is acceptable for outdoor use.

• Be sure your extension cord is properly wired

and in good electrical condition. Always replace a

damaged extension cord or have it repaired by a

qualiﬁ ed person before using it.

• Protect your extension cords from sharp objects,

excessive heat and damp or wet areas.

READ AND SAVE ALL

INSTRUCTIONS FOR FUTURE USE.

* Based on limiting the line voltage drop to ﬁ ve volts at

150% of the rated amperes.

EXTENSION CORDS

Recommended Minimum Wire Gauge

For Extension Cords*

Extension Cord Length

Nameplate

Amperes 25' 50' 75' 100' 150'

0 - 2.0

2.1 - 3.4

3.5 - 5.0

5.1 - 7.0

7.1 - 12.0

12.1 - 16.0

16.1 - 20.0

ASSEMBLY

WARNING To reduce the risk of injury,

always unplug tool before attaching or remov-

ing accessories or making adjustments. Use

only speciﬁ cally recommended accessories.

Others may be hazardous.

Removing and Replacing Quik-Lok

® Cords

(Cat. No. 5387-20)

MILWAUKEE's exclusive Quik-Lok

Cords provide

instant ﬁ eld replacement or substitution.

Fig. 1

1.To remove the Quik-Lok® Cord, turn the cord nut

1/4 turn to the left and pull it out.

2.To replace the Quik-Lok

® Cord, align the connec

tor keyways and push the connector in as far as it

will go. Turn the cord nut 1/4 turn to the right to lock.

Installing Bits into Keyed Chucks

Be sure that the shank of the bit and the chuck

jaws are clean. Dirt particles may cause the bit

to line up improperly.

Do not use bits larger

than the maximum

recommended ca-

pacity of the drill be-

cause gear damage

or motor overload-

ing may result. For

best performance, be

sure that the bits are

properly sharpened

before use.

1. Unplug the tool.

2. Open the chuck jaws wide enough to insert a bit.

Allow the bit to strike the bottom of the chuck.

Center the bit in the chuck jaws and tighten the

jaws by hand to align the bit.

3. Place the chuck key into each of the three holes

in the chuck, turning it clockwise to tighten the

chuck securely.

NOTE: Never use a wrench or means other than

a chuck key to tighten or loosen the chuck.

4. To remove the bit, insert the chuck key into one of

the holes in the chuck and turn it counterclockwise.

Fig. 2

Loosen

Tighten

Adjusting the Side Handle Position

1. Loosen the side handle by unscrewing the side

handle grip until the side handle rotates freely.

2. Rotate the side handle to the desired position.

3. Tighten the side handle grip securely.

WARNING To prevent personal injury,

always remove the chuck key from the chuck

after each use.

WARNING To reduce the risk of injury,

always use a side handle when using this tool.

Always brace or hold securely.

Fig. 3

Clamping lever

Side handle

grip

2. Slide the depth gauge rod backward or forward

until it is set for the desired depth (Fig. 4).

NOTE: The drilling depth is the distance between

the tip of the bit and the tip of the depth gauge

rod.

3. Release the clamping lever.

Setting the Depth Gauge

1. Press in the clamping lever (Fig. 3).

Chuck Removal

This tool is equipped with a threaded spindle to

hold the chuck. Before removing the chuck, unplug

the tool and open the chuck jaws. A left-handed

thread screw is located inside the chuck to pre-

vent the chuck from loosening when the tool is

operated in reverse direction. Remove the screw

by turning it clockwise. To remove the chuck, hold

the tool so that only the side of the chuck rests

ﬁ rmly and squarely on a solid workbench. Insert

the chuck key or

a chuck remover

bar in one of the

keyholes. Turn

the chuck so the

key is at about a

30° angle to the

bench top and

strike the key

sharply with a

hammer so the

chuck turns in

a counterclock-

wise direction

(lo o k ing from

the front of the

tool). This should

loosen the chuck

from the spindle

which has a right hand thread making it easy to

remove the chuck by hand.

NOTE: When replacing the chuck, always replace

the left hand thread screw in the chuck.

Fig. 4

Drilling Depth

WARNING To reduce the risk of injury,

always wear eye protection.

Fig. 5

Fig. B Fig. C

Specyfikacje produktu

Marka:	Milwaukee
Kategoria:	Wiertarka
Model:	5387-22

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Milwaukee 5387-22, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Wiertarka Milwaukee

Milwaukee M18 Fuel Super Hawg 2709-22 Instrukcja

8 Października 2024

Milwaukee SB 2-35 D Instrukcja

4 Października 2024

Milwaukee M18 BLH Instrukcja

4 Października 2024

Milwaukee M18 BLHX Instrukcja

4 Października 2024

Milwaukee K 900 S Instrukcja

4 Października 2024

Milwaukee K 545 S Instrukcja

4 Października 2024

Milwaukee M12 FPDX Instrukcja

4 Października 2024

Milwaukee K 700 S Instrukcja

4 Października 2024

Milwaukee M12 FDDX Instrukcja

4 Października 2024

Milwaukee M12 FPD2 Instrukcja

4 Października 2024

Instrukcje Wiertarka

Najnowsze instrukcje dla Wiertarka

Ozito BDP-500 Instrukcja

15 Października 2024

Einhell BM-G1100 E Instrukcja

14 Października 2024

Sun Joe 24V-DDK-LTX-PNK Instrukcja

14 Października 2024

DeWalt DWD450 Instrukcja

14 Października 2024

Black & Decker GC1800 Instrukcja

13 Października 2024

Rupes BH 252R Instrukcja

13 Października 2024

Makita HP2070 Instrukcja

13 Października 2024

Makita DHR263ZJ Instrukcja

12 Października 2024

Black & Decker BDCDE120 Instrukcja

10 Października 2024

Gamma BH-1500W Instrukcja

9 Października 2024