Instrukcja obsługi Milwaukee 5376-20

Milwaukee Wiertarka 5376-20

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Milwaukee 5376-20 (11 stron) w kategorii Wiertarka. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/11

Cat. No.

No de cat.

5376-20

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

1/2" HAMMER-DRILL

PERCEUSES À PERCUSSION 13 mm (1/2")

13 mm (1/2") TALADRO-MARTILLO

SPECIFIC SAFETY RULES

• Wear ear protectors when impact drilling.

Exposure to noise can cause hearing loss.

• Use auxiliary handle(s), if supplied with the

tool. Loss of control can cause personal injury.

• Hold power tools by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord. Cutting accessory contacting a “live” wire may

make exposed metal parts of the power tool “live”

and could give the operator an electric shock.

• Keep hands away from all cutting edges and

moving parts.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are

specially designed to ﬁ lter out microscopic particles.

Fig. B Fig. C

Fig. A

GROUNDING

WARNING Improperly connecting the

grounding wire can result in the

risk of electric shock. Check with a qualiﬁ ed

electrician if you are in doubt as to whether

the outlet is properly grounded. Do not modify

the plug provided with the tool. Never remove

the grounding prong from the plug. Do not

use the tool if the cord or plug is damaged. If

damaged, have it repaired by a MILWAUKEE

service facility before use. If the plug will not

ﬁ t the outlet, have a proper outlet installed by

a qualiﬁ ed electrician.

Grounded Tools: Tools with Three Prong Plugs

Tools marked “Grounding Required” have a three

wire cord and three prong grounding plug. The

plug must be connected to a properly grounded

outlet (See Figure A). If the tool should electrically

malfunction or break down, grounding provides a

low resistance path to carry electricity away from

the user, reducing the risk of electric shock.

The grounding prong in the plug is connected

through the green wire inside the cord to the

grounding system in the tool. The green wire in the

cord must be the only wire connected to the tool's

grounding system and must never be attached to

an electrically “live” terminal.

Your tool must be plugged into an ap-

propriate outlet, properly installed and

grounded in accordance with

all codes and ordinances. The

plug and outlet should look like

those in Figure A.

Double Insulated Tools: Tools with Two Prong

Plugs

Tools marked “Double Insulated” do not require

grounding. They have a special double insulation

system which satisﬁ es OSHA requirements and

complies with the applicable standards of Un-

derwriters Laboratories, Inc.,

the Canadian Standard Asso-

ciation and the National Elec-

trical Code. Double Insulated

tools may be used in either of

the 120 volt outlets shown in

Figures B and C.

SYMBOLOGY

Double Insulated

Volts Alternating Current

Amps

No Load Revolutions per

Minute (RPM)

BPM Blows per Minute (BPM)

Mexican Approvals Marking

Underwriters Laboratories, Inc.

United States and Canada

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive at-

mospheres, such as in the presence of ﬂ am-

mable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase

the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk

of electric shock.

• If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or

serious injury. Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the switch does not

turn it on and oﬀ. Any power tool that cannot be

controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc., in accordance with these instructions,

taking into account the working conditions and

the work to be performed. Use of the power tool

for operations diﬀerent from those intended could

result in a hazardous situation.

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the inﬂ uence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your ﬁ nger on the switch or energising power tools

that have the switch on invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

• Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

SERVICE SPECIFICATIONS

Tool Capacities

Cat. No. Volts

AC A No Load RPM No Load

BPM

Drill Only Hammer-Drill

Selﬀeed

Bit (Wood) Twist Drill

Bit (Steel) Carbide Tipped

Percussion Bit (concrete)

5376-20 120 8 0 - 2800 48,000 1-1/4" 1/2" 5/8"

Grounded tools require a three wire extension

cord. Double insulated tools can use either a two

or three wire extension cord. As the distance from

the supply outlet increases, you must use a heavier

gauge extension cord. Using extension cords with

inadequately sized wire causes a serious drop in

voltage, resulting in loss of power and possible tool

damage. Refer to the table shown to determine the

required minimum wire size.

The smaller the gauge number of the wire, the

greater the capacity of the cord. For example, a 14

gauge cord can carry a higher current than a 16

gauge cord. When using more than one extension

cord to make up the total length, be sure each cord

contains at least the minimum wire size required. If

you are using one extension cord for more than one

tool, add the nameplate amperes and use the sum

to determine the required minimum wire size.

Guidelines for Using Extension Cords

• If you are using an extension cord outdoors,

be sure it is marked with the sufﬁ x “W-A” (“W”

in Canada) to indicate that it is acceptable for

outdoor use.

• Be sure your extension cord is properly wired

and in good electrical condition. Always replace

a damaged extension cord or have it repaired by

a qualiﬁ ed person before using it.

• Protect your extension cords from sharp objects,

excessive heat and damp or wet areas.

READ AND SAVE ALL

INSTRUCTIONS FOR FUTURE USE.

Recommended Minimum Wire Gauge

for Extension Cords*

Extension Cord Length

* Based on limiting the line voltage drop to ﬁ ve volts

at 150% of the rated amperes.

Nameplate

Amperes

0 - 2.0

2.1 - 3.4

3.5 - 5.0

5.1 - 7.0

7.1 - 12.0

12.1 - 16.0

16.1 - 20.0

25'

75'

100'

150'

50'

EXTENSION CORDS

WARNING To reduce the risk of injury,

always use a side handle when us-

ing this tool. Always brace or hold securely.

ASSEMBLY

WARNING To reduce the risk of injury,

always unplug tool before attaching

or removing accessories or making adjust-

ments. Use only speciﬁ cally recommended

accessories. Others may be hazardous.

Adjusting the Side Handle Position

1. Loosen the side handle by unscrewing the side

handle grip until the side handle rotates freely.

2. Rotate the side handle to the desired position.

3. Tighten the side handle grip securely.

Setting the Depth Gauge

1. Press in the clamping lever.

2. Slide the depth gauge rod backward or forward

until it is set for the desired depth. The teeth

must match the orientation on the side handle

to properly lock in place.

NOTE: The drilling depth is the distance between

the tip of the bit and the tip of the rod.

3. Release the clamping lever.

OPERATION

WARNING To reduce the risk of injury,

always unplug tool before attaching

or removing accessories or making adjust-

ments. Use only speciﬁ cally recommended

accessories. Others may be hazardous.

WARNING To reduce the risk of injury,

keep hands and cord away from the

bit and all moving parts.

WARNING To reduce the risk of injury

do not grasp the bit while the chuck is rotat-

ing or while the bit is falling from the chuck.

WARNING To reduce the risk of injury,

wear safety goggles or glasses with

side shields.

3. Place the chuck key into

each of the three holes

in the chuck, turning it

clockwise to tighten the

chuck securely.

NOTE: Never use a

wrench or means other

than a chuck key to tight-

en or loosen the chuck.

4. To remove the bit, insert

the chuck key into one of the holes in the chuck

and turn it counterclockwise.

Selecting Action

MILWAUKEE Hammer-Drills have two settings:

drilling and hammer-drilling.

1. For drilling, push the hammer-drill lever over

the drill symbol .

2. For hammer-drilling, push the hammer-drill

lever over the hammer symbol .

NOTE: To engage the hammering mechanism,

maintain pressure on the bit. When pressure on the

bit is released, the hammering action will stop.

Using Forward/Reverse Lever

The forward/reverse lever can only be adjusted

when the trigger is not pressed. Always allow the

motor to come to a complete stop before using the

forward/reverse lever.

1. For forward (clockwise) rotation, push the for-

ward/reverse lever to the

left (when viewed from

the back of the tool) as

shown.

2. For (counter-reverse

clockwise) rotation, push

the forward/reverse lever

to the right (when viewed

from the back of the tool) as shown. Allow the

motor to come to a full stop before reversing.

NOTE: When hammer-drilling, use the tool in for-

ward rotation (clockwise) only.

Forward

Reverse

Starting, Stopping & Controlling Speed

1. To start the tool, pull trigger.

2. To stop the tool, release trigger.

3. To vary the speed, increase or decrease pres-

sure to trigger. The further the trigger is pulled,

the greater the speed.

Locking Trigger

The lock button holds the trigger in the ON position

for continuous full speed use.

1. To lock the trigger, hold in the lock button while

pulling the trigger. Release the trigger.

2. To unlock the trigger, pull the trigger and release.

The lock button will pop out.

Operating

Position the tool, grasp the handles ﬁ rmly and pull

the trigger. Always hold the tool securely using both

handles and maintain control. This tool has been

designed to achieve top performance with only

moderate pressure. Let the tool do the work.

If the speed begins to drop oﬀ when drilling deep

holes, pull the bit partially out of the hole while the

tool is running to help clear dust. Do not use water

to settle the dust since it will clog the bit ﬂ utes and

tend to make the bit bind in the hole. If the bit should

bind, stop the tool, free the bit and begin again.

WARNING To prevent personal injury,

always remove the chuck key from

the chuck after each use.

Installing Bits into Keyed Chucks

Be sure that the shank of the bit and the chuck

jaws are clean. Dirt particles may cause the bit

to line up improperly. Do not use bits larger than

the maximum recommended capacity of the drill

because gear damage or motor overloading may

result. For best performance, be sure that the bits

are properly sharpened before use.

1. Unplug the tool.

2. Open the chuck jaws wide enough to insert a bit.

Allow the bit to strike the bottom of the chuck.

Center the bit in the chuck jaws and tighten the

jaws by hand to align the bit.

FUNCTIONAL DESCRIPTION

1. Side handle

2. Clamping lever

3. Depth gauge

4. Chuck

5. Hammer/Drill lever

6. Lock button

7. Trigger

8. Forward/Reverse lever

Specyfikacje produktu

Marka:	Milwaukee
Kategoria:	Wiertarka
Model:	5376-20

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Milwaukee 5376-20, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Wiertarka Milwaukee

Milwaukee M18 Fuel Super Hawg 2709-22 Instrukcja

8 Października 2024

Milwaukee SB 2-35 D Instrukcja

4 Października 2024

Milwaukee M18 BLH Instrukcja

4 Października 2024

Milwaukee M18 BLHX Instrukcja

4 Października 2024

Milwaukee K 900 S Instrukcja

4 Października 2024

Milwaukee K 545 S Instrukcja

4 Października 2024

Milwaukee M12 FPDX Instrukcja

4 Października 2024

Milwaukee K 700 S Instrukcja

4 Października 2024

Milwaukee M12 FDDX Instrukcja

4 Października 2024

Milwaukee M12 FPD2 Instrukcja

4 Października 2024

Instrukcje Wiertarka

Najnowsze instrukcje dla Wiertarka

Ozito BDP-500 Instrukcja

15 Października 2024

Einhell BM-G1100 E Instrukcja

14 Października 2024

Sun Joe 24V-DDK-LTX-PNK Instrukcja

14 Października 2024

DeWalt DWD450 Instrukcja

14 Października 2024

Black & Decker GC1800 Instrukcja

13 Października 2024

Rupes BH 252R Instrukcja

13 Października 2024

Makita HP2070 Instrukcja

13 Października 2024

Makita DHR263ZJ Instrukcja

12 Października 2024

Black & Decker BDCDE120 Instrukcja

10 Października 2024

Gamma BH-1500W Instrukcja

9 Października 2024