Instrukcja obsługi Microchip PIC24FJ64GA110

Microchip Niesklasyfikowane PIC24FJ64GA110

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Microchip PIC24FJ64GA110 (74 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/74
2007-2015 Microchip Technology Inc. DS70000195G-page 1
HIGHLIGHTS
This section of the manual contains the following major topics:
1.0 Introduction ....................................................................................................................... 2
2.0 I
2
C Bus Characteristics..................................................................................................... 4
3.0 Control and Status Registers ............................................................................................ 8
4.0 Enabling I
2
C Operation ................................................................................................... 18
5.0 Communicating as a Master in a Single Master Environment ........................................ 20
6.0 Communicating as a Master in a Multi-Master Environment .......................................... 34
7.0 Communicating as a Slave ............................................................................................. 37
8.0 Connection Considerations for I
2
C Bus .......................................................................... 61
9.0 Operation in Power-Saving Modes ................................................................................. 63
10.0 Peripheral Module Disable (PMDx) Registers ................................................................ 63
11.0 Effects of a Reset............................................................................................................ 63
12.0 Constant-Current Source ................................................................................................ 64
13.0 Register Maps................................................................................................................. 66
14.0 Design Tips ..................................................................................................................... 67
15.0 Related Application Notes............................................................................................... 68
16.0 Revision History .............................................................................................................. 69
Inter-Integrated Circuit (I2C)
dsPIC33/PIC24 Family Reference Manual
DS70000195G-page 2 2007-2015 Microchip Technology Inc.
This document supersedes the following PIC24 and dsPIC
®
DSC Family Reference Manual sections:
1.0 INTRODUCTION
The Inter-Integrated Circuit (I
2
C) module is a serial interface useful for communicating with other
peripheral or microcontroller (MCU) devices. The external peripheral devices may be serial
EEPROMs, display drivers, Analog-to-Digital Converters (ADC) and so on.
The I
2
C module can operate as any one of the following in the I
2
C system:
• Slave device
• Master device in a single master system (slave may be active)
• Master or slave device in a multi-master system (bus collision detection and arbitration are
available)
The I
2
C module contains an independent I
2
C master logic and a I
2
C slave logic, which generates
interrupts based on their events. In the multi-master systems, the user software is simply
partitioned into the master controller and the slave controller.
When the I
2
C master logic is active, the slave logic also remains active, detecting the state of the
bus and potentially receiving messages from itself in a single master system or from the other
masters in a multi-master system. No messages are lost during the multi-master bus arbitration.
In a multi-master system, the bus collision conflicts with the other masters in the system when
detected, and the module provides a method to terminate and then restart the message.
The I
2
C module contains a Baud Rate Generator (BRG). The I
2
C BRG does not consume other
timer resources in the device. Figure 1-1 illustrates the I
2
C module block diagram.
Key features of the I
2
C module include the following:
• Independent master and slave logic
• Multi-master support which prevents message losses in arbitration
• Detects 7-bit and 10-bit device addresses with configurable address masking in Slave mode
• Detects general call addresses as defined in the I
2
C protocol
• Bus Repeater mode, allowing the module to accept all messages as a slave, irrespective of
the address
• Automatic SCLx clock stretching provides delays for the processor to respond to a slave
data request
• Supports 100 kHz and 400 kHz bus specifications
• Supports the Intelligent Platform Management Interface (IPMI) standard
• Supports SDAx hold time for SMBus (300 nS or 150 nS) in Slave mode
Note: This family reference manual section is meant to serve as a complement to device
data sheets. Depending on the device variant, this manual section may not apply to
all PIC24 and dsPIC33 devices.
Please consult the note at the beginning of the “Inter-Integrated Circuit (I
2
C)”
chapter in the current device data sheet to check whether this document supports
the device you are using.
Device data sheets and family reference manual sections are available for
download from the Microchip Worldwide Web site at:
http://www.microchip.com
DS Number Section Number Title
DS70195 19 dsPIC33F/PIC24H Family Reference Manual
DS70330 19 dsPIC33E/PIC24E Family Reference Manual
DS39702 24 PIC24F Family Reference Manual
DS70235 19 PIC24H Family Reference Manual
DS70068 21 dsPIC30F Family Reference Manual
Note:
For more information, refer to the SDAHT bit description in the specific device data sheet.
2007-2015 Microchip Technology Inc. DS70000195G-page 3
Inter-Integrated Circuit (I
2
C)
Figure 1-1: I
2
C Block Diagram
I2CxRCV
Internal
Data Bus
SCLx
SDAx
Shift
Match Detect
Clock
Address Match
Clock
Stretching
I2CxTRN
LSB
Shift Clock
BRG
Reload
Control
T
CY
or T
CY
/2
(1)
Acknowledge
Generation
I2CxCONH
I2CxSTAT
Control Logic
Read
LSB
Write
Read
I2CxBRG
I2CxRSR
Write
Read
Write
Read
Write
Read
Write
Read
Write
Read
Down Counter
I2CxCONL
Write
Read
Note 1: Refer to the specific device data sheet for the clock rate.
I2CxADD
Start and Stop
Bit Detect
Start and Stop
Bit Generation
Collision
Detect
I2CxMSK

Specyfikacje produktu

Marka: Microchip
Kategoria: Niesklasyfikowane
Model: PIC24FJ64GA110

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Microchip PIC24FJ64GA110, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Microchip

Microchip

Microchip ATECC608B Instrukcja

7 Października 2024
Microchip

Microchip HV860 Instrukcja

7 Października 2024
Microchip

Microchip EVB-LAN9255 Instrukcja

7 Października 2024
Microchip

Microchip LX4580 Instrukcja

7 Października 2024
Microchip

Microchip LX7720 Instrukcja

7 Października 2024
Microchip

Microchip AT32UC3C0128C Instrukcja

4 Października 2024
Microchip

Microchip AT32UC3A3256 Instrukcja

4 Października 2024
Microchip

Microchip AT32UC3A364 Instrukcja

4 Października 2024
Microchip

Microchip AT32UC3B0256 Instrukcja

4 Października 2024
Microchip

Microchip AT32UC3A0512 Instrukcja

4 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024