Instrukcja obsługi Microchip MIC4801YM

Microchip nieskategoryzowany MIC4801YM

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Microchip MIC4801YM (4 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
MIC4801 Evaluation Board
High Efficiency 600mA Single Channel
Linear WLED Driver with
Ultra Fast PWM™ Control
Ultra Fast PWM is a trademark of Micrel, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
General Description
The MIC4801 is a high efficiency, single channel, White
LED (WLED) driver. This constant current linear device is
designed to drive a single high power WLED up to 600mA
and features a low dropout of 130mV at 400mA (typical).
Brightness is controlled through an Ultra Fast PWM™
interface which can operate from 1% to 100% duty cycle.
The MIC4801 is available in an 8-pin SOIC leaded
package with a junction temperature range of -40°C to
+125°C
Requirements
The MIC4801 evaluation board requires a power supply
that is capable of delivering at least 1A while providing an
input voltage between 3.0V and 5.5V.
Precautions
The MIC4801 evaluation board is designed for an input
voltage no greater than 6V. This evaluation board does not
have reverse polarity protection; hence, applying a
negative voltage to the VIN terminal may damage the
device.
Getting Started
1. Connect an external supply to VIN. Apply the
desired input voltage across VIN and ground
terminals, J2 and J3, respectively, paying careful
attention to polarity and supply voltage
(3.0VVIN5.5V). An ammeter may be placed
between the input supply and the VIN terminal to
the evaluation board. Ensure that the supply
voltage is monitored at the VIN terminal. The
ammeter and/or power lead resistance can reduce
the voltage supplied to the input. VBAT is
connected to VIN through a 0 resistor, R1.
2. Enable/Disable the MIC4801
To enable the device, apply a DC voltage of 1.2V or
greater to the EN pin. This allows for full brightness of
the WLED (100% duty cycle). The EN pin can also be
used for dimming by connecting a PWM signal and
varying its duty cycle (please refer to the Ultra Fast
PWM™ Dimming Interface Section in datasheet).
Pulling EN low for more than 40ms forces the
MIC4801 into a low IQ sleep mode. Do not leave the
EN pin floating as this may cause an indeterminate output
state. A pull up resistor of 10k is placed from EN (JP1)
to VIN to ensure that the WLED is ON when an input signal
is applied.
3. Setting LED current with RSET resistor.
The average LED current may be calculated using the
equation below:
( )
140.0)(
4920
)(
140.0
)(
4920
)(
−Ω
⋅
=
+
⋅
=Ω
kR
D
mAI
mAI
D
kR
SET
LED
LED
SET
D is the duty cycle of the LED current during PWM
dimming; D=1 when device is fully ON. The stock
evaluation board uses an RSET value of 12.1k which
corresponds to ILED of 411mA.
4. Measuring WLED current.
To measure WLED current, simply insert an ammeter
in series with the WLED(s). Keep in mind that a series
ammeter will add a small voltage drop, so the voltage
at the WLED terminal, D1, should be used when
making dropout measurements with a series ammeter.
Ordering Information
Part Number Description
MIC4801YM EV Evaluation board with the Single
Channel MIC4801 device
March 2011 M9999-032111-B
Micrel, Inc. MIC4801 Evaluation Board
March 2011 2 M9999-032111-B
MIC4801 Evaluation Board Schematic
MIC4801
C1
2.2µF
VIN
RSET
EN
D1
GND
VB
A
T
J1
LED1
R1
0Ω
R2
open
R3
10kΩ
R4
12.1kΩ
VIN
J2
RSET
J4 D1
J6
GND
J5
GND
J3
C2
open
JP1
Bill of Materials
Item Part Number Manufacturer Description Qty.
C1608X5R0J225K TDK(1)
06036D225KAT2A AVX
(2)
GRM188R60J225KE19D Murata(3)
VJ0603G225KXYAT Vishay(4)
C1
CL10B225KQ8NNNC Samsung(5)
Ceramic Capacitor, 2.2µF, 6.3V, X5R, Size 0603 1
C2 Open 1
R1 CRCW06030000FKEA Vishay
Resistor, 0Ω, 1%, 1/16W, Size 0603 1
R2 open
R3 CRCW060310K0FKEA Vishay
Resistor, 10kΩ, 1%, 1/16W, Size 0603 1
R4 CRCW060312K1FKEA Vishay Resistor, 12.1kΩ, 1%, 1/16W, Size 0603 1
LED1 W42180 Seoul Semiconductor(6) 3.8W High Power WLED 1
U1 MIC4801YM Micrel, Inc. (7) 600mA Single Channel Ultra Fast PWM™
Linear WLED Driver 1
Notes:
1. TDK: www.tdk.com
2. AVX: www.avx.com
3. Murata: www.murata.com
4. Vishay: www.vishay.com
5. Samsung: www.samsung.com
6. Seoul Semiconductor: www.seoulsemicon.com
7. Micrel, Inc.: www.micrel.com
Micrel, Inc. MIC4801 Evaluation Board
March 2011 3 M9999-032111-B
PCB Layout Recommendations
Top Layer
Bottom Layer

Specyfikacje produktu

Marka: Microchip
Kategoria: nieskategoryzowany
Model: MIC4801YM

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Microchip MIC4801YM, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany Microchip

Microchip

Microchip EMC1824 Instrukcja

5 Lipca 2024
Microchip

Microchip EVB-USB3740 Instrukcja

5 Lipca 2024
Microchip

Microchip EVB-USB3503 Instrukcja

5 Lipca 2024
Microchip

Microchip EVB-LAN7430 Instrukcja

5 Lipca 2024
Microchip

Microchip ATSAMHA1G14A-B Instrukcja

5 Lipca 2024
Microchip

Microchip MCP1631 Instrukcja

5 Lipca 2024
Microchip

Microchip ATSAM4LS4B Instrukcja

5 Lipca 2024
Microchip

Microchip EVB-USB2507 Instrukcja

5 Lipca 2024
Microchip

Microchip EVB-USB2502 Instrukcja

5 Lipca 2024
Microchip

Microchip PAC1710 Instrukcja

5 Lipca 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Meec Tools

Meec Tools 010-084 Instrukcja

6 Października 2024
Outwell

Outwell Scenic Road 250 Instrukcja

5 Października 2024
Impact

Impact Qualite QL-3560-LED Instrukcja

4 Października 2024
Impact

Impact QuikBalance Instrukcja

4 Października 2024
Impact

Impact CA-112 Instrukcja

4 Października 2024
Impact

Impact Forever Ready Cool FRC-24-LED Instrukcja

4 Października 2024
Impact

Impact LS-BHA Instrukcja

4 Października 2024
Impact

Impact LKB-5C Instrukcja

4 Października 2024
Impact

Impact Varipole Drop Ceiling Adapter Instrukcja

4 Października 2024
Impact

Impact RST-001 Instrukcja

4 Października 2024