Instrukcja obsługi Microchip MIC3263


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Microchip MIC3263 (32 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/32
MIC3263
Six-Channel WLED Driver for
Backlighting Applications with
Flicker-Free Dimming
MLF is a registered trademark of Micrel, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 http://www.micrel.com
January 2010 M9999-012110
can be set to a
ed to 16
frequency from 400 KHz to 1.8 MHz to a
sizes. The 6V to 40V wide input voltage
allows direct operation from 6V or high
batteries commonly found in notebook compute
range of − °40 C to + °125 C.
Data sheets and support documentation can be found on
Micrel’s web site at: www.micrel.com
General Description
The MIC3263 is a high-efficiency Pulse Width
(PWM) boost switching regulator that is op
constant-current WLED d
Modulation
timized for
lications. river backlighting ap
The MIC3263 drives six channels of up to ten
channel. Each channel is matched in current to
for constant brightness across the screen a
programmed from 15mA to 30mA.
The MIC3263 provides a very flexible dimm
scheme with better accuracy and noise imm
dimming frequency
p
WLEDs per
within ±3%
nd can be
ing control
unity. The
ny value between
100Hz and 20kHz by an external resistor. T
ratio is determined by the duty cycle of a dim
control input signal and can be set to one of 16
he dimming
ming ratio
levels with
a minimum ratio of 1%.The LED dimming curre
an external resistor to allow programming of
between 15mA and 30mA.
The dimming ratio of the MIC3263 is fix
nt is set by
LED current
log levels
to better match the sensitivity of the human e
the dimming levels has hysteresis to avo
between levels and a
ye. Each of
id skipping
llow for high noise immun
The MIC3263 has a programmable PW
ity.
M switching
llow small inductor
range of MIC3263
cell count Li-Ion
r s.
The MIC3263 is available in a low-profile 24-pin 4mm x
4mm MLF® package and has a junction temperature
.
nge
white LEDs
from 15mA to 30mA
ith open and short LEDs
og levels sets the dimming ratio
the jitter from the dimming
control input signal and eliminates dimming flicker
control
rrent matching ±3%
ED current setting ±2%
ing frequency from 400kHz to
High efficiency up to 90%
Low (<40μA) shutdown current over temperature
rature protection
mmable over-voltage protection
° + °C to 125 C junction temperature range
ilable in 24-pin 4mm x 4mm MLF® package
ons
White LED driver for backlighting
LCD Panels and Monitors
Multimedia players
Navigation equipment
Gaming systems
Video poker
Slot machines
_________________________________________________________________________________________________________________________
Features
6V to 40V wide input voltage ra
Drives 6 channels of up to 10
Programmable WLED current
Highly reliable operation w
Accurate 16 dimming l
from 1% to 100%
Flicker-Free Dimming filters
Allows external dimming
LED channel cu Accurate
Accurate initial L
Programmable switch
1.8MHz
Over tempe
Progra
• − 40
Ava
Applicati
Notebooks
Micrel, Inc. MIC3263
January 2010 2 M9999-012110
Typical Application
MIC3263 Typical Application Schematic
Micrel, Inc. MIC3263
January 2010 3 M9999-012110
mati
Junction Temperature Range Package Lead Finish
Ordering Infor on
(1)
Part Number
MIC3263YML –40° to +125°C 24-Pin 4mm x 4mm MLF® Pb-Free
Note:
1. Other Voltage available. Contact Micrel for detail
Pin Configuration
24-Pin 4mm x 4mm MLF®
Pin Description
Pin Number Pin Name Pin Function
1 FS
Hz to 1.8MHz.
W Booster Switching Frequency:
Connect a resistor-to-GND to set the switching frequency from 400k
2 RS ent Resistor. LP Slope Compensation Adjustm
3 OV ltage divider virtual ground. PS OVP and FB vo
4 O or amp in the Boost stage. VP Overvoltage Protection Input. This is also the FB voltage for the err
5 MO equency range:
z and VDD for 1.5kHz to 20kHz. If DFS is connected to V
DD, MODE pin is
for an external dimming pulse input.
DE Select a dimming fr
0V for 100Hz to 2kH
used
6 DF Hz through an external resistor and MODE.
Requires a series RC for stability.
If DFS is connected to VDD, an external dimming pulse can be applied to the MODE pin.
S Set a dimming frequency from 100Hz to 20k
7 COMP Loop Compensation connect R and C-to-GND.
8 DRC Dimming Ratio Control Pulse:
Its duty cycle is converted to one of 16 dimming levels. The duty-cycle difference between two
adjacent levels is ±6.25%. And about 2% duty-cycle hysteresis exists between two adjacent
levels to eliminate dimming flicker.
DRC can be from 100Hz to 40kHz.
9 CINT Integration Cap:
Use a 0.01µF for 2kHz to 20kHz and 0.1µF for 100Hz 2kHz.


Specyfikacje produktu

Marka: Microchip
Kategoria: Niesklasyfikowane
Model: MIC3263

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Microchip MIC3263, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Microchip

Microchip

Microchip ATECC608B Instrukcja

7 Października 2024
Microchip

Microchip HV860 Instrukcja

7 Października 2024
Microchip

Microchip EVB-LAN9255 Instrukcja

7 Października 2024
Microchip

Microchip LX4580 Instrukcja

7 Października 2024
Microchip

Microchip LX7720 Instrukcja

7 Października 2024
Microchip

Microchip AT32UC3C0128C Instrukcja

4 Października 2024
Microchip

Microchip AT32UC3A3256 Instrukcja

4 Października 2024
Microchip

Microchip AT32UC3A364 Instrukcja

4 Października 2024
Microchip

Microchip AT32UC3B0256 Instrukcja

4 Października 2024
Microchip

Microchip AT32UC3A0512 Instrukcja

4 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024