Instrukcja obsługi Microchip MIC2291

Microchip Niesklasyfikowane MIC2291

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Microchip MIC2291 (10 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/10
MIC2291
1.2A PWM Boost Regulator Photo Flash
LED Driver
PowerPAK is a trademark of Siliconix, Inc.
MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (
408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
May 2007
1 M9999-051507
General Description
The MIC2291 is a 1.2MHz Pulse Width Modulation (PWM),
boost-switching regulator that is optimized for high-current,
white LED photo flash applications. With a guaranteed
switch current of 1.2A, the MIC2291 easily drives a string
of 3 white LEDs in series at 100mA, ensuring a high level
of brightness and eliminating several ballast resistors.
The MIC2291 implements a constant frequency, 1.2MHz
PWM control scheme. The high frequency PWM operation
saves board space by reducing external component sizes.
The added benefit of the constant frequency PWM
scheme, in contrast to variable frequency topologies, is
much lower noise and input ripple injected back to the
battery source.
To optimize efficiency, the feedback voltage is set to only
95mV. This reduces the power dissipation in the current
set resistor, and allows the lowest total output voltage,
hence minimal current draw from the battery.
The MIC2291 is available with 2 levels of over-voltage
protection, 15V, and 34V. This allows designers to choose
the smallest possible external components with the
appropriate voltage ratings for their applications.
The MIC2291 is available in low-profile, Thin SOT23 5-pin
and 8-pin 2mm × 2mm MLF
®
package options. The
MIC2291 has a junction temperature range of –40°C to
+125°C.
Data sheets and support documentation can be found on
Micrel’s web site at www.micrel.com.
Features
• 2.5V to 10V input voltage
• Output voltage up to 34V
• 1.2A switch current
• 1.2MHz PWM operation
• 95mV feedback voltage
• Overvoltage protection (OVP)
– Options for 15V and 34V
• Stable with ceramic capacitors
• <1% line and load regulation
• 1µA shutdown current
• Over temperature protection
• UVLO
• Low-profile Thin SOT23-5 package option
• 2mm × 2mm MLF
®
package option
• –40°C to +125°C junction temperature range
Applications
• Photo Flash LED driver
• Cell phones
• PDAs
• GPS systems
• Digital cameras
• IP phones
• LED flashlights
Typical Application
10µH
0.22µF
ceramic
95mV
1-Cell
Li Ion
3V to 4.2V
1µF
2
3
1
4
5
MIC2291xD5
VIN
EN
SW
FB
GND
100mA
10µH
0.22µF
1µF1-Cell
Li Ion
3V to 4.2V
MIC2291-15xML
VIN
EN
SW
OVP
FB
GND 95mV
100mA
Thin SOT23 Flash LED Driver 2mm x 2mm Flash LED Driver with Output OVP
Micrel, Inc. MIC2291
May 2007
2 M9999-051507
Ordering Information
Part Number Marking* Overvoltage
Protection
Junction
Temp. Range
Package Lead Finish
MIC2291BD5 SSAA ― –40° to +125°C 5-Pin Thin SOT23 Standard
MIC2291YD5 SSAA ― –40° to +125°C 5-Pin Thin SOT23 Pb-Free
MIC2291-15BML STA 15 –40° to +125°C 8-Pin 2mm x 2mm MLF
®
Standard
MIC2291-15YML STA** 15 –40° to +125°C 8-Pin 2mm x 2mm MLF
®
Pb-Free
MIC2291-34BML STC 34 –40° to +125°C 8-Pin 2mm x 2mm MLF
®
Standard
MIC2291-34YML STC** 34 –40° to +125°C 8-Pin 2mm x 2mm MLF
®
Pb-Free
Notes:
* Under bar / Over bar symbol may not be to scale.
** Over bar symbol located after Pin 1 identifier.
Pin Configuration
FB GND
EN VIN
SW
31
5
2
4
OVP
VIN
EN
A
GND
PGND
SW
FB
NC
1
2
3
4
8
7
6
5
EP
5-Pin TSOT23 (D5) 8-Pin 2mm x 2mm MLF
®
(ML)
Pin Description
Pin Number
TSOT23-5
Pin Number
2x2 MLF-8
Pin Name Pin Name
1 7 SW Switch node (Output): Internal power BIPOLAR collector.
2 GND Ground (Return): Ground.
3 6 FB Feedback (Input): Output voltage sense node. Connect the cathode
of the LED to this pin. Connect current set resistor from this pin to
ground.
4 3 EN Enable (Input): Logic high (≥1.5V) enables regulator. Logic low
(≤0.4V) shuts down regulator.
5 2 VIN Supply (Input): Input Voltage.
― 1 OVP Overvoltage protection (Input): Connect to the output to clamp the
maximum output voltage.
― 4 AGND Analog ground. Internally connected to ground.
― 8 PGND Power ground.
― 5 NC No connect (no internal connection to die).
― EP GND Ground (Return): Exposed backside pad.
Micrel, Inc. MIC2291
May 2007
3 M9999-051507
Absolute Maximum Ratings(1)
Supply Voltage (V
IN
).......................................................12V
Switch Voltage (V
SW
)....................................... –0.3V to 34V
Enable Pin Voltage (V
EN
)................................... –0.3V to V
IN
FB Voltage (V
FB
)...............................................................6V
Switch Current (I
SW
) .........................................................2A
Storage Temperature (T
s
) .........................–65°C to +150°C
ESD Rating
(3)
.................................................................. 2kV
Operating Ratings(2)
Supply Voltage (V
IN
).......................................... 2.5V to 10V
Junction Temperature (T
J
) ........................–40°C to +125°C
Package Thermal Resistance
2x2 MLF-8 (θ
JA
) .................................................93°C/W
Thin SOT23-5 (θ
JA
)..........................................256°C/W
Electrical Characteristics(4)
T
A
= 25°C, V
IN
= V
EN
= 3.6V; V
OUT
= 10V; I
OUT
= 40mA, bold values indicate –40°C< T
J
< +125°C, unless noted.
Symbol Parameter Condition Min Typ Max Units
V
IN
Supply Voltage Range 2.5 10 V
V
UVLO
Under Voltage Lockout 1.8 2.1 2.4 V
I
VIN
Quiescent Current V
FB
> 200mV, (not switching) 2.8 5 mA
I
SD
Shutdown Current V
EN
= 0V(5) 0.1 1 µA
V
FB
Feedback Voltage (±5%) 90 95 100 mV
I
FB
Feedback Input Current V
FB
= 95mV –450 nA
Line Regulation(7) 3V ≤ V
IN
≤ 5V 0.5 1 %
Load Regulation(7) 5mA ≤ I
OUT
≤ 40mA 0.5 %
D
MAX
Maximum Duty Cycle 85 90 %
I
SW
Switch Current Limit 1.2 A
V
SW
Switch Saturation Voltage I
SW
= 1.0A 550 mV
I
SW
Switch Leakage Current V
EN
= 0V, V
SW
= 10V 0.01 5 µA
V
EN
Enable Threshold TURN ON
TURN OFF
1.5
0.4
V
V
I
EN
Enable Pin Current V
EN
= 10V(6) 20 40 µA
f
SW
Oscillator Frequency 1.05 1.2 1.35 MHz
V
OVP
Overvoltage Protection MIC2291BML- 15 only
MIC2291BML- 34 only
13
30
14
32
16
34
V
V
T
J
Overtemperature
Threshold Shutdown
Hysteresis
150
10
°C
°C
Notes:
1. Absolute maximum ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating
the device outside of its operating ratings. The maximum allowable power dissipation is a function of the maximum junction temperature, T
J(max)
, the
junction-to-ambient thermal resistance, θ
JA
, and the ambient temperature, TA. The maximum allowable power dissipation will result in excessive die
temperature, and the regulator will go into thermal shutdown.
2. The device is not guaranteed to function outside its operating rating.
3. Devices are ESD sensitive. Handling precautions recommended. Human body model.
4. Specification for packaged product only.
5. I
SD
= I
VIN
.
6. See “Typical Characteristics” section for other V
EN
.
7. Guaranteed by design.

Specyfikacje produktu

Marka: Microchip
Kategoria: Niesklasyfikowane
Model: MIC2291

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Microchip MIC2291, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Microchip

Microchip

Microchip ATECC608B Instrukcja

7 Października 2024
Microchip

Microchip HV860 Instrukcja

7 Października 2024
Microchip

Microchip EVB-LAN9255 Instrukcja

7 Października 2024
Microchip

Microchip LX4580 Instrukcja

7 Października 2024
Microchip

Microchip LX7720 Instrukcja

7 Października 2024
Microchip

Microchip AT32UC3C0128C Instrukcja

4 Października 2024
Microchip

Microchip AT32UC3A3256 Instrukcja

4 Października 2024
Microchip

Microchip AT32UC3A364 Instrukcja

4 Października 2024
Microchip

Microchip AT32UC3B0256 Instrukcja

4 Października 2024
Microchip

Microchip AT32UC3A0512 Instrukcja

4 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024